Panasonic Electronic Print Board KX-BP800 Operating Instructions

11
Precautions
Beforeyo ustar
Battery
ProjectorIf batteries are used improperly, batteries may leak, causing corrosion of the
product, or they may burst. To prevent this, always follow the precautions given
below.
C Always remove batteries from the Electronic Pen and Electronic Eraser if\
 they are
not to be used for an extended period of time.
C Use the same type of batteries. Do not mix different types.
C Do not mix old and new batteries.
C Always insert batteries with their polarity properly oriented...

12
Part Names and Functions
Electronic Pen/Electronic
Eraser Position Receiver
Screen Film
AC Inlet
Tray
Interactive Connector
Power Cord
Printer Open Lever
Push down this lever to open
the printer door.
Output Port
Outputs copy paper that 
has been copied. Can hold 
up to 20 sheets.
Paper Cover
Open this cover when loading
copy paper.
Printer Door
Open the printer door when loading
transfer film or when removing
paper jams.
(See pages 14, 20 and 21.)
ON
OFF
Control Panel
Electronic Pen (See page 24)...

13
Before you start
Part Names and Functions
nThe control panel
NamePanelDescription
Contrast/
Remaining
Film
Indicator
Contrast
Key
This lamp indicator notifies the user when the time to replace the therm\
al
transfer film is approaching (estimated) and of the printing contrast \
used
during copying.
Indicator off : Normal printing contrast.
Indicator on : Darker than normal printing contrast.
Indicator flashing : Almost time to replace the thermal transfer film.
(Note that only about 15 more sheets may...

ON
OFF
14
Installing Thermal Transfer Film
Load the thermal transfer film into the film cassette and install in the printer.
Printer Open 
Lever
Printer Door
Blue Gear
Blue GearGear Tabs
Grooves
(Blue)
Green Gear
TabsGrooves
Green Gear
Green Gears Thermal
Transfer Film
1Set the power switch to on ( |).
C  will flash on the multi-copy/error indicator
when the thermal transfer film has run out.
2Push down the printer open lever and open the
printer door.
3Insert the four gears into the new thermal
transfer...

15
Installing Thermal Transfer Film
Using
Thermal
Transfer Film
Load thermal transfer
film in this derection
Film Cassette
Blue Label
Blue Gear
4Load the thermal transfer film into the film
cassette.
C Load the thermal transfer film into the film
cassette so that the blue gear inserted in the
thermal transfer film is located on the blue label
side of the film cassette. Push in the direction
of the arrow until you hear all four gear shafts
click in place.
Slack Prohibited
Label
Thermal 
Transfer Film5If...

16
Loading Copy Paper
It is possible to load up to 80 sheets of Letter size copy paper [assuming a paper weight of 80g/m2(21 lbs)].
Note that only Letter paper may be used.
When the unit is first used or when   flashes on the multi-copy/error indicator to indicate that the unit is out of
paper, load copy paper as described below.
Notes on Loading Copy Paper
Follow the guidelines below to ensure smooth and accurate printing by the unit.
COnly use Letter size copying paper having a weight of 60 to 90g/m...

17
Loading Copy Paper
Using
Paper Cover
Magnets
2Pull the paper cover forward as shown in the
right figure. 
C
The magnets are used as fasteners to hold the
paper cover closed.
Maximum Paper Limit Guide
3To prevent paper jams such as those caused
by multiple sheets feeding, once fan the paper
thoroughly, square it, align it with the guide
inside, and insert as far as it will go. 
C
Only use Letter size copying paper having a
weight of 60 to 90g/m2(16 to 24 lbs) as the copy
paper for this unit.
C Do not...

18
Making Copies
This section describes how to copy text and illustrations drawn on the screen.
ON
OFF
1Set the power switch to on ( | ).
C1 will light on the multi-copy/error indicator to
indicate that the unit is ready to copy.
12
Output PaperCopy Key
KX-BP800Panasonic
2Press the copy key .
CText and illustrations on the screen will be
copied and copies emerge from the output port.
CThe output port can hold up to 20 sheets of
copy paper. (Note that exceeding the output
ports capacity may result in...

19
Making Copies
Using
Copying the front
of the screen Press .
n
Copy types and procedures
Copy TypeProcedure
Copying the back
of the screen Press  to move the screen to be copied to the front.
Press .
Making multiple
copies (up to 9)Select the number of copies (1 to 9) by pressing  as necessary.
Press .
C Press  to stop copying in mid-operation.
Making 2-screen
copies
C
C
Copying the front and
back of the screen on a
single sheet of paper 
Press .1 2
Copying chart
paper Chart paper can be attached to...

20
Replacing Thermal Transfer Film
Notes on Replacing Thermal Transfer Film
The unit is capable of producing about 15 more copies when the contrast/remaining film indicator begins to flash.
The unit has run out of thermal transfer film and can no longer make copies when the multi-copy/error indicator
flashes  . Separately available replacement film (KX-BP081 or KX-BP082) may be purchased from the dealer
where you purchased the unit. Thermal transfer film is replaced as follows.
COnly use the designated...