Panasonic Electronic Board Ub-7325 Operating Instructions

Assembling the Electronic Board
31
Installation Manual
■Assembly
1Assemble the optional stand or wall-mounting kit.
■If you are using a stand, refer to page 36.
■If you are using a wall-mounting kit, refer to page 40.
2Remove the electronic board from the shipping box.
Remove the joints, then remove the electronic board from the shipping box.
• Do not touch the screen film surface, as this may damage it.
• The shipping box, cushioning material, and other packing material will be necessary if you ever...

Assembling the Electronic Board
32
3Install the electronic board.
Install the electronic board using the stand (option) 
or wall-mounting kit (option). 
■ Using the st and (option)
1) Hang the electronic board on the optional 
stand.
• The electronic board can be mounted 
200 mm (7 
7/8”) higher than hang position  A 
by hanging it with the wing bolts  B.
2) Secure the stand fixture to the electronic  board using the two wing-bolts [M5 x 12 mm 
(15/32”)] provided with the  stand (option).
■Using the...

Assembling the Electronic Board
33
Installation Manual
4Connect the power cord.
1) Securely fit the supplied power cord into the 
AC inlet on the printer unit.
2) Fit the power cord into the cable holder.
5Wipe the screen film surface.
Soak a soft cloth with water, wring well, and 
wipe the screen film surface.
• Do not wipe the screen film surface with paint 
thinner, benzene, or cleaners that contain abrasives. 
Doing so may cause discoloration.
• Do not wipe the screen film surface with a dry cloth....

34
Electronic Board Operations Check
After assembling the electronic board, perform the procedures presented in the following table to make sure it 
functions properly.
*
1Contact the store or dealer from which the unit was purchased.
StepPoints to Check
SymptomSolutions
1Turn on the power switch.“ ” flashes after “ ” lights up. (Normal operation)
(If not) Check power cord. (See step 
4 on page 33.)
2Open the printer door and attach the 
accessory thermal transfer film, then 
close the printer door.
•...

35
Installation Manual
Repacking
Perform Assembly Steps 2 through 4 on pages 31 - 33 in reverse to repack the electronic board and accessories. 
Use the joints to fasten the shipping box.
• Do not touch the screen film surface, as this may damage it.
Eraser Thermal transfer film
Manuals
CD-ROM Power cord
Markers
Joints
Joints Joints
Joints
JointsJoints
Electronic board
Shipping box
Shipping box
Caution 

36
Assembling the Optional Stand (KX-B061)
■Accessories
The package box for the optional stand includes the parts noted below; please confirm that all parts are present 
before beginning installation
.
*1The accessory wrench is required to fasten or loosen the screws  ,  ; please store it carefully for future use.
*2These are used for other models.
●
Before assembly, be sure to lock the casters.
No.Part nameIllustrationQ’tyNo.Part nameIllustrationQ’ty
Stand base 2 Wing bolt
M5 x 12 mm (
15/32”)6
Pipe...

Assembling the Optional Stand (KX-B061)
37
Installation Manual
■Assembly
1Assembling the stand
■Assembling the fall-prevention extension legs
The fall-prevention extension legs increase the safety of the electronic board.
• Install and always set the fall-prevention legs when using the stand.
• When tightening the screw  , hold the nut   with pliers.
Note
• When folding back the fall-prevention extension legs to release the lock, perform as follows.
■Inserting the covers  to the pipes 
Fall-prevention...

Assembling the Optional Stand (KX-B061)
38
■Assembling the stand
Note
*1 Do not tighten the screw   too much. This may deform the pipes.
Assemble with the holes 
toward the front.
           
Locking
casters side
(rear)Pull the fall-prevention extension legs 
down (fall-prevention extension legs 
will be fixed by the lock pin.)
1 1
1
2
Locking casters side
(rear) 

Assembling the Optional Stand (KX-B061)
39
Installation Manual
2Attach the fixtures   with the four wing-bolts.
3Assemble and install the electronic board.
Refer to step 3 on page 32. 

40
Optional Wall-mounting Kit (KX-B063)
Before attempting installation of this wall-mounting kit, we strongly recommend consulting with the building manager, 
engineer, or architect. The installer needs to know the type of construction used for the wall intended for this 
installation and the location of wall studs. Selection of hardware is critical for safe wall-mounting, and depends on the 
nature of wall construction. Installation should not occur until this consultation takes place.
• Do not attach...