Panasonic Electronic Board Ub-7325 Operating Instructions

							Assembling the Electronic Board
31
Installation Manual
■Assembly
1Assemble the optional stand or wall-mounting kit.
■If you are using a stand, refer to page 36.
■If you are using a wall-mounting kit, refer to page 40.
2Remove the electronic board from the shipping box.
Remove the joints, then remove the electronic board from the shipping box.
• Do not touch the screen film surface, as this may damage it.
• The shipping box, cushioning material, and other packing material will be necessary if you ever need to 
repackage the electronic board, so do not throw them away.
Eraser Thermal transfer film
Manuals
CD-ROM Power cord
Markers
Joints
Joints Joints
Joints
JointsJoints
Electronic board
Shipping box
Shipping box
Caution 
						

							Assembling the Electronic Board
32
3Install the electronic board.
Install the electronic board using the stand (option) 
or wall-mounting kit (option). 
■ Using the st and (option)
1) Hang the electronic board on the optional 
stand.
• The electronic board can be mounted 
200 mm (7 
7/8”) higher than hang position  A 
by hanging it with the wing bolts  B.
2) Secure the stand fixture to the electronic  board using the two wing-bolts [M5 x 12 mm 
(15/32”)] provided with the  stand (option).
■Using the wall-mount ing kit (option)
1) Hang the electronic board on the optional wall-
mounting fixtures.
2) Secure the wall-mounting fixture to the  electronic board using the two wing-bolts 
[M5 x 12 mm (15/32”)] provided with the  wall-
mounting kit (option) .
• When mounting the electronic board, avoid banging  it. Such impact may break the internal light or cause 
other damage.
• After mounting the electronic board, gradually apply  weight to it to make sure that the wall is strong 
enough to support it.
A
B
Caution 
						

							Assembling the Electronic Board
33
Installation Manual
4Connect the power cord.
1) Securely fit the supplied power cord into the 
AC inlet on the printer unit.
2) Fit the power cord into the cable holder.
5Wipe the screen film surface.
Soak a soft cloth with water, wring well, and 
wipe the screen film surface.
• Do not wipe the screen film surface with paint 
thinner, benzene, or cleaners that contain abrasives. 
Doing so may cause discoloration.
• Do not wipe the screen film surface with a dry cloth. 
Doing so may create static electricity.
6Check operations.
Refer to “Electronic Board Operations Check” 
on page 34.
Cable holder 
Caution 
						

							34
Electronic Board Operations Check
After assembling the electronic board, perform the procedures presented in the following table to make sure it 
functions properly.
*
1Contact the store or dealer from which the unit was purchased.
StepPoints to Check
SymptomSolutions
1Turn on the power switch.“ ” flashes after “ ” lights up. (Normal operation)
(If not) Check power cord. (See step 
4 on page 33.)
2Open the printer door and attach the 
accessory thermal transfer film, then 
close the printer door.
• Installing Thermal Transfer Film 
procedure (refer to the Operating 
Instructions on page 10)
“ ” flashes. (Normal operation)
(If not) Check thermal transfer film.
3Open the paper cover and insert 
ordinary Letter test paper, then close 
the paper cover.
• Loading Copy Paper procedure 
(refer to the Operating 
Instructions on page 11)“ ” lights up. (Normal operation)
(If not) Check copy paper.
4Open the printer door.“ ” flashes. (Normal operation)
(If not)
*1
5Close the printer door.“ ” lights up. (Normal operation)
(If not)
*1
6Press .
Press .Screen is fed. (Normal operation)
The screen film surface is not fed 
smoothly.
*1
There are strange noises.
7Use the accessory marker to draw 
a large   filling the entire 
copyable area of the screen film 
surface.
• Copyable area (refer to the 
Operating Instructions on 
page 7)
Press  twice.
Press .“ ” lights up and three copies are 
made.(Normal operation)
Three copies are not made.
*1
The entire readable area is not 
printed.
There are strange noises or paper 
jams during the copying process.
Multiple sheets of paper are fed 
through at the same time.
8Press   to move the screen 
film surface. Write letters, etc. with 
the marker.
Press  once.
Press .The Contrast/Remaining Film 
indicator light is turned on and one 
copy is made.(Normal operation)
The Contrast/Remaining Film 
indicator light is not turned on.*1
The image is not copied properly.
There are strange markings on the 
copy sheet 
(e.g., stripes or lines).
9Press  once.The Contrast/Remaining Film 
indicator light is turned off.(Normal operation)
(If not)
*1 
						

							35
Installation Manual
Repacking
Perform Assembly Steps 2 through 4 on pages 31 - 33 in reverse to repack the electronic board and accessories. 
Use the joints to fasten the shipping box.
• Do not touch the screen film surface, as this may damage it.
Eraser Thermal transfer film
Manuals
CD-ROM Power cord
Markers
Joints
Joints Joints
Joints
JointsJoints
Electronic board
Shipping box
Shipping box
Caution 
						

							36
Assembling the Optional Stand (KX-B061)
■Accessories
The package box for the optional stand includes the parts noted below; please confirm that all parts are present 
before beginning installation
.
*1The accessory wrench is required to fasten or loosen the screws  ,  ; please store it carefully for future use.
*2These are used for other models.
●
Before assembly, be sure to lock the casters.
No.Part nameIllustrationQ’tyNo.Part nameIllustrationQ’ty
Stand base 2 Wing bolt
M5 x 12 mm (
15/32”)6
Pipe 2Support 
bracket2
Cover 2Fall-preven-
tion extension 
leg4
Side bar (A) 2 Screw
M6 x 60 mm (2 
3/8”)4
Side bar (B) 1 Nut 4
Screw
M8 x 45 mm (1 
25/32”)12 Wrench             *
1
1
Fixture
(left)2Wing bolt
(Not use*
2)
M4 x 8 mm (5/16”)8
Fixture
(right)2Screen holder 
bracket
(Not use*
2)4
Locking the casters
(Push this side)
Releasing the lock 
						

							Assembling the Optional Stand (KX-B061)
37
Installation Manual
■Assembly
1Assembling the stand
■Assembling the fall-prevention extension legs
The fall-prevention extension legs increase the safety of the electronic board.
• Install and always set the fall-prevention legs when using the stand.
• When tightening the screw  , hold the nut   with pliers.
Note
• When folding back the fall-prevention extension legs to release the lock, perform as follows.
■Inserting the covers  to the pipes 
Fall-prevention extension legs• Caster locks are attached to 
the back side.
Caution
1
1
2 
						

							Assembling the Optional Stand (KX-B061)
38
■Assembling the stand
Note
*1 Do not tighten the screw   too much. This may deform the pipes.
Assemble with the holes 
toward the front.
           
Locking
casters side
(rear)Pull the fall-prevention extension legs 
down (fall-prevention extension legs 
will be fixed by the lock pin.)
1 1
1
2
Locking casters side
(rear) 
						

							Assembling the Optional Stand (KX-B061)
39
Installation Manual
2Attach the fixtures   with the four wing-bolts.
3Assemble and install the electronic board.
Refer to step 3 on page 32. 
						

							40
Optional Wall-mounting Kit (KX-B063)
Before attempting installation of this wall-mounting kit, we strongly recommend consulting with the building manager, 
engineer, or architect. The installer needs to know the type of construction used for the wall intended for this 
installation and the location of wall studs. Selection of hardware is critical for safe wall-mounting, and depends on the 
nature of wall construction. Installation should not occur until this consultation takes place.
• Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall-mounting 
fixture bolts to metal laths or wire laths can cause heat, smoke or a fire.
1. Tools required:
A minimum of eight (8) pieces of appropriate wall-support hardware (molley, toggle, etc.)
NOTE: THIS HARDWARE MUST BE LOCALLY PROCURED, IT IS NOT INCLUDED IN THE KIT.
Drill (and drill bit of correct size) for hardware installation
Screw driver (Both phillips (+) and slotted (–) will be required.)
Tape measure
Tape or thumb-tacks (2 pcs)
Bubble type level
2. Pre-requisites
1. Before installation, make sure that the wall intended for installation is capable of supporting flush-
mounted.
UB-7325 is 130 kgf (287 lbs.).
2. The position of the intended installation is of adequate size for the selected Panaboard.
UB-7325 is 1,516 mm (H) × 1,648 mm (W) [5' (H) × 5' 5" (W)].
3. An outlet is within 3 m (9' 10
1/8" ), and not located behind the Panaboard.
■Accessories
The package box for the optional wall-mounting kit includes the parts noted below; please confirm that all parts are 
present before beginning installation. Eight screws for mounting the fixtures on the wall are not provided. Please 
purchase the appropriate wall-mounting hardware (sold in stores). Refer to page 42.
*These are used for other models.
No.Part nameIllustrationQ’tyNo.Part nameIllustrationQ’ty
Wall-mounting 
fixture L2Screw
(Not use*)
M4 x 16 mm (
20/32”)4
Wall-mounting 
fixture R2
Wall-mounting 
template
(Not use*)1
Wing bolt
M5 x 12 mm (
15/32”)
(For mounting of the 
electronic board)2Use the wall-
mounting template 
provided with 
UB-7325.
Caution