Panasonic DLP Projector PT-DZ780 PT-DW750 PT-DX820 Operating Instructions

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 111
[PROJECTOR SETUP] menu
On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   71) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[PROJECTOR ID]
The projector has an ID number setting function that can be used when mu\
ltiple projectors are used side by side 
to enable simultaneous control or individual control...

Chapter 4 Settings — [PROJECTOR SETUP] menu
112 - ENGLISH
[COOLING CONDITION]
Change the fan control depending on the direction of projection.
Set [COOLING CONDITION] according to the projection direction, but set it to [AUTO] normally. Using the 
projector with [COOLING CONDITION] set incorrectly may shorten the life of the lamp.

30°
30° 30°
30°
[VERTICAL UP SETTING]
[FLOOR 
SETTING] [CEILING 
SETTING]
[VERTICAL DOWN SETTING] Projection direction
1) Press as to select [COOLING CONDITION].
2)  
Press...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 113
[LAMP RELAY]
Switch the lamp to be turned on automatically by specifying the day of the week and time.
The degradation of the lamp due to continuous usage can be reduced by au\
tomatically switching the lamp to be 
turned on when using the projector continuously for a week or more.
1) 
Press 
 as to select [LAMP RELAY].
2)
 
Press 
 qw to switch the item.
[OFF] Disables lamp relay.
[24H] Switches the lamp daily.
[1WEEK] Switches the lamp weekly....

Chapter 4 Settings — [PROJECTOR SETUP] menu
114 - ENGLISH
[BRIGHTNESS CONTROL]
The projector is equipped with a luminance sensor to measure brightness and functions to correct screen 
brightness resulting from changes in lamp brightness.
By using this function, it is possible to reduce changes in overall brig\
htness of the multiple screens due to lamp 
degradation and suppress variation in brightness to preserve uniformity \
when constructing multiple screens using 
multiple projectors.
Setting...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 115
8) Press qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Performs corrections by the brightness sensor on one projector without s\
ynchronizing with the other 
projectors.
The duration that the constant brightness is kept will become longer by \
setting the value of 
[BRIGHTNESS CONTROL GAIN] smaller.
[GROUP A]
[GROUP B]
[GROUP C]
[GROUP D] Synchronizes corrections in multiple projectors by the brightness...

Chapter 4 Settings — [PROJECTOR SETUP] menu
116 - ENGLISH
 fFor continued use longer than 24 hours, set [BRIGHTNESS CONTROL  SETUP] to [CALIBRATION TIME], or set [LAMP RELAY] 
(x   page   113). If it is not set, correction will not be performed automatically.
 fThe [CALIBRA

TION TIME] setting will be reflected at the time when you enter the time.
 fThe [CALIBRA

TION MESSAGE] setting will be reflected at the time when items are switched using  qw.
Displaying [BRIGHTNESS CONTROL STATUS]
Display the...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 117
When [MODE] of [BRIGHTNESS CONTROL SETUP] is set to [AUTO] and [LINK] is set to [OFF]
The screen shows the status of the brightness control in one projector
5
1
6
RETURN
LINK
PROJECTOR OFF
BRIGHTNESS CONTROL STATUSMENU
When [MODE] of [BRIGHTNESS CONTROL SETUP] is set to [PC]
5
1
6
RETURN
MODE
PROJECTOR PC
BRIGHTNESS CONTROL STATUSMENU
1 Display the name of the projector
.
2  
Display the synchronized group.
3

 
Display the IP
  address of the...

Chapter 4 Settings — [PROJECTOR SETUP] menu
118 - ENGLISH
Brightness control adjustment procedure example
The steps exemplify an adjustment to link the brightness of eight projectors connected in a network.
1) 
Connect all projectors to the hub using LAN cables. ( x

  page   142)
2)
 
Switch on all projectors and start projection.
3)

 
Set [LAMP
  SELECT] to either [DUAL] or [SINGLE] for all projectors.
4)
 
Set [MODE] of [BRIGHTNESS CONTROL
  SETUP] to [OFF], and select [APPLY], and then press the...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 119
[SCHEDULE]
Set the command execution schedule for each day of the week.
Enabling/disabling the schedule function
1) Press as to select [SCHEDULE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the schedule function.
[ON] Enables the schedule function. Refer to “How to assign a program” (
x
  page   119) or “How to set a 
program” (x
  page   119) for how to set the schedule.
Note
 fWhen...

Chapter 4 Settings — [PROJECTOR SETUP] menu
120 - ENGLISH
[COMMAND]Detailed settings of 
[COMMAND] Description
[POWER ON] ―Switches on the projector.
[STANDBY] ―Enters standby.
[SHUTTER] [OPEN]
Disables the shutter function (shutter: open).
[CLOSE] Enables the shutter function (shutter: closed).
[INPUT] [RGB1]
Switches the input to RGB1.
[RGB2] Switches the input to RGB2.
[DVI
- D]Switches the input to DVI
- D.
[HDMI] Switches the input to HDMI.
[DIGITAL LINK] Switches the input to DIGITAL LINK.
[SDI]...