Panasonic DLP Based Projector PT-DZ570U PT-DW530U PT-DX500U Operating Instructions

ENGLISH - 71
Settings
See  
z“Navigating through the menu ”  
(
Æpage 39).
See 
 
z“MAIN MENU” and “SUB MENU ”  
(
Æpage 40).
 
JREGISTERED SIGNAL STATUS
The name can be set for each sub memory. 
z
MEMORY NO. : A1 (1-2) 
z
Registering a signal to the list
When a new format input signal is applied to the 
projector, press  button to register to the 
SIGNAL LIST.
Note
You can register data up to 96 in total number of the 
 
z
signal data and any corresponding sub memory data.
The memories are numbered over...

72 - ENGLISH
Settings
SECURITY menu
See  
z“Navigating through the men u”  
(
Æpage 39).
See 
 
z“MAIN MENU” and “SUB MENU ”  
(
Æpage 40).
When you apply to the [SECURITY] menu 
 
z
before you change the password to your original, 
perform to input the following factory default 
password operation.
Press ▲►▼◄▲►▼◄  and  button.
Attention
When you apply to the SECURITY menu after you 
 
z
change the password to your original in the [SECURITY 
PASSWORD CHANGE] menu, input the original 
password operation....

SECURITY menu
ENGLISH - 73
Settings
DISPLAY SETTING
You can set your original text, such as company 
name or URL information, to display regularly on the 
projected image while projecting.
Press ▲▼ to select [DISPLAY 
1  ) 
SETTING].
Press ◄► to switch [DISPLAY 
2  ) 
SETTING].
The setting will change as follows each time  
z
◄► is pressed.
OFFTEXTLOGO1
OFF The text display is disabled.
TEXT The text display is enabled.
LOGO1 The picture registered by the user 
will be projected.
Note
Separate software...

SECURITY menu
74 - ENGLISH
Settings
CONTROL DEVICE SETUP
Control from the remote control and main unit controls 
can be restricted.
Press ▲▼ to select [CONTROL 
1  ) 
DEVICE SETUP].
Press  button.
2  ) 
The [CONTROL DEVICE SETUP] screen will  
z
be displayed.
Press ▲▼ to select [CONTROL 
3  ) 
PANEL] or [REMOTE CONTROLLER].
Press  button.
4  ) 
[ 
zCONTROL PANEL] screen or [REMOTE 
CONTROLLER] screen will be displayed.
 
JCONTROL PANEL
Restriction of control from the main unit controls  
z
can be set....

ENGLISH - 75
Maintenance
Monitor Lamp indicators
Managing the indicated problems
If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as 
follow.Attention
 
JLAMP indicator
Lamp 
indication Information
Check point Remedial measure
Lighting in red Indicates the time 
for replacing the 
lamp unit. Did you notice a “REPLACE 
 
z
LAMP” message on the screen 
when turning on the projector 
power supply? This lamp monitor lights up when the 
 
z
lamp unit...

Monitor Lamp indicators
76 - ENGLISH
Maintenance
 
JTEMP indicator
Lamp 
indication Information
Check point Remedial measure
Lighting in red Warm-up status
Did you turn on the power when 
 
z
the ambient temperature was 
lower than approx. 0 °C (32 °F)? Wait about 5 minutes in the current 
 
z
status.
Install the unit in a location having 
 
z
an ambient temperature from 0 °C 
(32 °F) - 45 °C (113 °F).
High temperature 
inside. (WARNING) Check the ventilation port is 
 
z
blocked.
Is the room air...

ENGLISH - 77
Maintenance
Replacement
Before replacing the unit
Turn off the POWER switch of the projector in proper way and disconnect the pow\
er plug from the wall outlet.  
z
(Æpages 31, 33)
Be sure to observe the procedure 
 
z“Powering off the projector” (Æpage 33) when performing power supply 
operation.
Replacing the unit
Lamp unit 
J
The LAMP unit is consumable product. You can check the duration of usage time using [LAMP] of [STATUS] 
(
Æpage 67) in the [PROJECTOR SETUP] menu.
Replacement of the...

Replacement
78 - ENGLISH
Maintenance
AIR FILTER 
J
Optional air filter (service part) is available from any Panasonic dealer
.
When you replace the projector lamp, replace the air filter at the same time.
The replacement lamp unit (part number ET-LAD60A, 1 bulb unit) package contains one air filter (part number 
ET-LAD60A), but the ET-LAD60AW lamp unit (part number ET-LAD60AW, 2 bulb units) package contains two 
air filters (part number ET-LAD60AW).
Procedure of Air Filter/Lamp Unit replacement 
J...

Replacement
ENGLISH - 79
Maintenance
Use a Phillips screwdriver to loosen 
4  ) 
the “Lamp unit cover fixing screw” 
(3 screws) for the lamp unit to be 
replaced until the screws turn freely. 
Hold the “Handle” of the “Lamp unit” 
and gently pull the lamp unit out from 
the projector.
Replace the new LAMP unit in correct 
5  ) 
direction.
Use a Phillips screwdriver to securely 
6  ) 
tighten the 2 “Lamp Unit cover fixing 
screw” for lamp unit.
Note
When the lamp unit is replaced, the duration of usage...

80 - ENGLISH
Maintenance
Troubleshooting
Should any problem persist, contact your dealer.
ProblemCauseReference 
page
Power does not turn 
on. The power cord may not be connected.
 
z—
The  switch is turned off.
 
z33
No electric supply is at the wall outlet.
 
z—
The circuit breakers have tripped.
 
z—
[LAMP indicator] or [TEMP indicator]is lit or flashes.
 
z75, 76
The lamp unit cover has not been securely installed.
 
z78
No picture appears. The video signal input source may not be connected to a...