Panasonic DLP Based Projector PT-DZ570U PT-DW530U PT-DX500U Operating Instructions

About Your Projector
ENGLISH - 21
Preparation
Setting projector ID number 
to remote control
Each projector can be assigned a unique ID number, 
and the handheld remote’ s number must be set to 
match the intended projector.
The ID number of the projector is set to “ALL” on 
shipping, and use the ID ALL button of the remote 
control when using only a single projector.
Press  button, and the 
1  ) 
projector (s) will display it’s current ID 
number onscreen. Within 5 seconds, 
use the numeric keys (1-6)...

22 - ENGLISH
Getting Started
Setting up
Projection method
You can use the projector with any of the following 4 projection methods.\
 To set the desired method in the 
projector.
 
JMounting on the ceiling and 
 
projecting from front 
JSetting on a desk/floor and 
 
projecting from rear
(Using translucent screen)
Menu ÛMethod
INSTALLATION FRONT/CEILING
COOLING   
CONDITION CEILING SETTINGMenu ÛMethod
INSTALLATION REAR/FLOOR
COOLING   
CONDITION FLOOR SETTING
 
JMounting on the ceiling and 
 
projecting...

Setting up
ENGLISH - 23
Getting Started
Screen size and throw distance
When planning the projector and screen geometry, refer to the figures below and the information on the following 
pages for reference. After the projector is roughly positioned, picture size and vertical pic\
ture positioning can be 
finely adjusted with the powered zoom lens and lens shifting mechanism.
L (LW/LT) ÛProjection distance (m)
SH Height of the projection area (m)
SW Width of the projection area (m)
SD Diagonal length of...

Setting up
24 - ENGLISH
Getting Started
Projection distance for PT-DZ570U 
J
(All measurements below are approximate and may differ slightly from the actual measurements.)
Projection size
For 4:3 aspect ratio For 16:9 aspect ratioFor 16:10 aspect ratio
Screen diagonal (SD) Minimum 
distance (LW) Maximum 
distance (LT) Minimum 
distance (LW) Maximum 
distance (LT) Minimum 
distance (LW) Maximum 
distance (LT)
  1.02 m (40") 1.40 m (4.59')2.85 m (9.35')1.26 m (4.13')2.58 m (8.46')1.23 m...

Setting up
ENGLISH - 25
Getting Started
Projection distance for PT-DW530U 
J
(All measurements below are approximate and may differ slightly from the actual measurements.)
Projection size
For 4:3 aspect ratio For 16:9 aspect ratioFor 16:10 aspect ratio
Screen diagonal (SD) Minimum 
distance (LW) Maximum 
distance (LT) Minimum 
distance (LW) Maximum 
distance (LT) Minimum 
distance (LW) Maximum 
distance (LT)
  1.02 m (40") 1.47 m (4.82')2.99 m (9.81')1.33 m (4.36')2.71 m (8.89')1.29 m...

Setting up
26 - ENGLISH
Getting Started
Projection distance for PT-DX500U 
J
(All measurements below are approximate and may differ slightly from the actual measurements.)
Projection size
For 4:3 aspect ratio For 16:9 aspect ratio
Screen diagonal (SD) Minimum distance
(LW) Maximum distance
(LT) Minimum distance
(LW) Maximum distance
(LT)
  1.02 m (40") 1.20 m (3.94') 2.46 m (8.07')1.31 m (4.30')2.68 m (4.30')
  1.27 m (50") 1.51 m (4.95') 3.08 m (10.10') 1.65 m...

Setting up
ENGLISH - 27
Getting Started
Front leg adjusters and throwing angle
You can screw up/down the front leg adjusters to control the angle of the\
 projector for adjusting the throwing 
angle.
Attention
Heated air comes out of the air exhaust port. Do not touch the air exhau\
st port directly.
 
z
Adjustable range
Front adjuster leg : 20 mm 

28 - ENGLISH
Getting Started
Connections
Before connection to the projector
Read carefully the instruction manual for the device to be connected. 
z
Turning off the power switch of the devices before connecting cables. 
z
If any connection cable is not supplied with the device, or if no option\
al cable is available for connection of the  
z
device, prepare a necessary system connection cable to suit the device.
Video signals containing too much jitter may cause the images on the scre\
en to randomly...

Connections
ENGLISH - 29
Getting Started
Pin assignments and signal names of  terminal 
J
Outside view Pin No.
Signal names Pin No.Signal names
T.M.D.S data 2-—
T.M.D.S data 2++5V
T.M.D.S data 2/4 shieldGND
—Hot plug detection
—T.M.D.S data 0-
DDC clockT.M.D.S data 0+
DDC dataT.M.D.S data 0/5 shield
——
T.M.D.S data 1-—
T.M.D.S data 1+T.M.D.S clock shield
T.M.D.S data 1/3 shieldT.M.D.S clock +
—T.M.D.S clock -
The PT-DX500U has the same DVI-D input terminal with the 180-degree rotated pi\
n layout.
: 
Û...

Connections
30 - ENGLISH
Getting Started
Connecting example : Computers
Note
The DVI-D signal input terminal supports only a single link.
 
z
For the specifications of the RGB signals that can be applied from the PC, refer to 
 
z “List of compatible signals
”.  
(
Æpage 87)
If your computer has the resume feature (last memory), the computer ma\
y not function properly until the resume capability 
 
z
is disabled.
When the SYNC ON GREEN signal is input, do not input sync signals to the\
 SYNC/HD and VD...