Panasonic Digital Disk Recorders Wj Hd309 Operating Instructions

31
cFilter recording events.
Filter recording events by time and date
Move the cursor using the arrows button and rotate the jog
dial to enter the time and date.
Press the SET button to determine the entered time and
date.
The recording event in the entered time range will be listed
and displayed.
Filter recording events by camera channel
Select camera channel numbers (1 - 16 for the WJ-HD316,
1 - 9 for the WJ-HD309) using the arrows button to apply fil-
tering. It is possible to select camera channels...

32

nTo stop playback, press the STOP button.
The indicator on the PLAY/PAUSE button will go off and
playback will be stopped.
Live images will be displayed on monitor 2 and the VGA
monitor.
Important:
In the recording event list, the start time of recording
will be displayed.
When events occurred successively, the contents of the
event log and the recording event list will not always
match since the unit continues to record the first occur-
ring event.
 Search for a motion detected
time and date from...

33
xPress the SET button.
The VMD search window will be displayed.
Enter a camera channel number and time range on the
VMD search window for the VMD search.
To search using the same conditions as the previous
search, press the PLAY/PAUSE button.
Go to step 12 when the VMD search is performed and a list
of the results is displayed after the PLAY/PAUSE button is
pressed. 
cMove the cursor using the arrows button and
rotate the jog dial to enter the camera channel
number and time range for the VMD search....

34
⁄0Select the sensitivity using the arrows button
(DC) from the following.
OFF:Motion will not be detected
LOW:Low sensitivity
MID:Standard sensitivity
HIGH:High sensitivity
⁄1Rotate the jog dial to select EXIT on the sta-
tus bar to exit from the motion detection area
setup window.
mMove the cross cursor using the arrows button
to a point to be determined as the end point of
the motion detection area.
Press the SET button to determine the selected point as the
end point of the motion detection area....

35
⁄2Move the cursor to select a detection mode
using the arrow buttons and rotate the jog dial
to check the radio button next to the selected
detection mode. Press the SET button to deter-
mine the selection.
Refer to page 36for further information about each of the
detection modes.

Move the cursor to the parameter box using the arrows but-
ton (C) to select a masking duration from the following.
1 s/1 m/1 h/24 h

Move the cursor to an area for the settings of VECTOR
using the arrows button (C) and...

36
Any motion will be detected anywhere in the A, B, C, D
areas.
Note:In the ANY AREA mode, it is possible to set the
masking duration. When the masking duration is set,
motion will be ignored for a certain period (set duration
as the masking duration) in the same area. It is conve-
nient to set the masking duration to make the subject
period shorter in case it is necessary to search an
extended time range or when searching through many
results.

It will be subject to listing if an object moves within...

37
 Search for a marked point and
play from that point (Marking
search)
Display the recording time of the recorded images with a
marked point in a list or a thumbnail and select the desired
recording time to play. Refer to page 24for further informa-
tion about marking.
zPress the SEARCH button repeatedly until the
marking list window is displayed.
The result list of the marking search will be displayed on
monitor 2 and the VGA monitor.
Use the arrows button (CD) to switch between displaying
the list...

38
MONITOR LIVE IMAGES
It is possible to display live images on a single screen or a
multi-screen.
On a single sequential display (It is also possible that dis-
played images from cameras will be switched automatical-
ly)
 Displaying Live Images on a
Single Screen
zPress the MONITOR1/MONITOR2 button to
select the monitor.
When monitor 1 is selected, the indicator will light.
When monitor 2 or the VGA monitor is selected, the indica-
tor will not light.
xPress a camera selection button 
(1 - 16 for the...

39
 Displaying on a Multi-screen
It is possible to display images on a multi-screen (4, 7, 9,
10, 13, 16 for the WJ-HD316, 4, 7, 9 for the WJ-HD309).
zPress the MONITOR1/MONITOR2 button to
select the monitor.
When monitor 1 is selected, the indicator will light.
When monitor 2 is selected, the indicator will not light.
xPress the SHIFT button.
The SHIFT indicator will light.
cPress a camera selection button 1 - 6 (1 - 3 for
the WJ-HD309) to select a desired multi-
screen.
Camera selection button 1:...

40
 Sequential Display
Displayed images from cameras will be switched automati-
cally.
Camera images will be displayed sequentially according to
the settings performed in advance.
zPress the MONITOR1/MONITOR2 button to
select the monitor.
When monitor 1 is selected, the indicator will light.
When monitor 2 is selected, the indicator will not light.
xPress the SHIFT button.
The SHIFT indicator will light.
cPress the SEQ button.
The camera selection button respective to the displayed
image will light...