Panasonic Digital Disk Recorders Wj Hd309 Operating Instructions

							31
cFilter recording events.
Filter recording events by time and date
Move the cursor using the arrows button and rotate the jog
dial to enter the time and date.
Press the SET button to determine the entered time and
date.
The recording event in the entered time range will be listed
and displayed.
Filter recording events by camera channel
Select camera channel numbers (1 - 16 for the WJ-HD316,
1 - 9 for the WJ-HD309) using the arrows button to apply fil-
tering. It is possible to select camera channels using the
camera selection buttons [1] - [16] for the WJ-HD316 ([1] -
[9] for the WJ-HD309).
The selected camera channels will turn white.
Press the SET button to determine the selection of camera
channel numbers.
The recording events of the selected camera channels will
be listed.
Note:When operating the system controller, select a cam-
era channel using the numeric keypad. In this case, it is
impossible to select 10 CH to 16 CH.
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
b
c
v
cc
PAN/
TILT
START
1JAN 03
SET : [SET]  CANCEL : [ESC]
00 00  TIME&DATE FILTERING
..:AM
END
1 JAN 03 0 00..:AM
Filter recording events by the recording event
Move the cursor to select the recording event (refer to page
28) using the arrows button (CD) and rotate the jog dial to
ON.
Press the SET button to determine the selection.
The recording events of the selected filter will be listed.
Filter recording events by text information
Rotate the jog dial to select OFF, WITH TEXT or WITHOUT
TEXT.
Press the SET button to determine the selection.
The recording events filtered by the selected filter will be
listed.
vRotate the jog dial to select therecording event
to be played.
It is possible to turn the page by rotating the shuttle ring.
bPress the PLAY/PAUSE button.
The LISTED indicator and the indicator on the PLAY/PAUSE
button will light and playback of the selected recording
event will start.
Note:When the LISTED indicator is lit, only listed recording
events are available to be played. Press the LISTED
button during playback to make all recording events
available to be played.
1
2345678
91011 12 13 14 15 16
CAMERA FILTERINGCAMERA
SET : [ SET ]      CANCEL : [ ESC ]
SET : [ SET ]      CANCEL : [ ESC ]
REC EVENT FILTERING
OFF
ON
ON
ON
ON
ON
ON
EMERGENCYVMD
TERMINAL
COMMAND
VIDEO LOSSMANUALSCHEDULE
TEXT FILTERING
WITHOUT TEXT
SET : [ SET ]      CANCEL : [ ESC ]
TIME&DATE
01ch
01ch
01ch
01ch
01ch
01ch
01ch
01chMANUAL
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL CAM REC EVTABCDEFGHIJ
ABCDEFGHIJ
ABCDEFGHIJ
ABCDEFGHIJ
ABCDEFGHIJ
ABCDEFGHIJ
ABCDEFGHIJ
ABCDEFGHIJTEXT
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
TIME&DATE    SEARCH    REC EVENT    SEARCH    VMD    SEARCH    MARK
TIME&DATECAMERAREC EVENTTEXTUNLOCK FILTER
TOTAL 25.APR.03*12:34:56 AM  25.APR.03*12:34:56 AM12345 
						

							32

nTo stop playback, press the STOP button.
The indicator on the PLAY/PAUSE button will go off and
playback will be stopped.
Live images will be displayed on monitor 2 and the VGA
monitor.
Important:
In the recording event list, the start time of recording
will be displayed.
When events occurred successively, the contents of the
event log and the recording event list will not always
match since the unit continues to record the first occur-
ring event.
 Search for a motion detected
time and date from the recorded
images and play it (VMD search)
Search for a motion detected time and date from all the
images recorded in all the recording modes, and display a
list or a thumbnail of the results.
Select a time and date displayed on the result list or thumb-
nail to play it.
It is possible to filter by camera channel, time and date,
detection area or search mode, to list the time and date of
events that were recorded when motion was detected.
zPress the SEARCH button repeatedly until the
VMD search list is displayed.
The result list of the VMD search will be displayed on moni-
tor 2 and the VGA monitor.
(The list in the displayed window is of the results of the pre-
vious search.)
Use the arrows button (CD) to switch between displaying
the list window and the thumbnail window alternately.

⇔
TIME&DATE
01ch
01ch
01ch
01ch
01ch
01ch
01ch
01chCAM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
TIME&DATE    SEARCH    REC EVENT    SEARCH    VMD    SEARCH    MARK
VMD SEARCH
TOTAL 25.APR.03*12:34:56 AM  25.APR.03*12:34:56 AM12345
R
2 R
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
n
PAN/
TILT
R
2 R
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
z
PAN/
TILT
TIME&DATE
01ch
01ch
01ch
01ch
01ch
01ch
01ch
01chCAM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
TIME&DATE    SEARCH    REC EVENT    SEARCH    VMD    SEARCH    MARK
VMD SEARCH
TOTAL 25.APR.03*12:34:56 AM  25.APR.03*12:34:56 AM12345 
						

							33
xPress the SET button.
The VMD search window will be displayed.
Enter a camera channel number and time range on the
VMD search window for the VMD search.
To search using the same conditions as the previous
search, press the PLAY/PAUSE button.
Go to step 12 when the VMD search is performed and a list
of the results is displayed after the PLAY/PAUSE button is
pressed. 
cMove the cursor using the arrows button and
rotate the jog dial to enter the camera channel
number and time range for the VMD search.
vPress the SET button.
The motion detection area setup window will be displayed.
To search using the same conditions as the previous
search, press the PLAY/PAUSE button.
Go to step 12 when the VMD search is performed and a list
of the results is displayed after the PLAY/PAUSE button is
pressed.
Note:If no image was recorded in the time range set in
step 3, the motion detection area setup window will not
be displayed when the SET button is pressed.
bRotate the jog dial to select SETUP AREA on
the status bar.
Note:It is possible to set all displayed areas as motion
detection areas by pressing the SET button after select-
ing ALL AREAS.
nMove the cross cursor using the arrows button
to a point to be determined as the start point of
the motion detection area.
Press the SET button to determine the selected point as the
start point of the motion detection area.
START CAMERA
1
CAM1
JAN 03
SET : [SET]    SEARCH : [PLAY]    CANCEL : [ESC]
12 00  SELECT CAMERA & DATE
..:AM
END
1 JAN 03 12 00..:AM
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
PAN/
TILT
cb cn
xvn
START CAMERA
1
CAM1
JAN 03
SET : [SET]    SEARCH : [PLAY]    CANCEL : [ESC]
12 00  SELECT CAMERA & DATE
..:AM
END
1 JAN 03 12 00..:AM 
						

							34
⁄0Select the sensitivity using the arrows button
(DC) from the following.
OFF:Motion will not be detected
LOW:Low sensitivity
MID:Standard sensitivity
HIGH:High sensitivity
⁄1Rotate the jog dial to select EXIT on the sta-
tus bar to exit from the motion detection area
setup window.
mMove the cross cursor using the arrows button
to a point to be determined as the end point of
the motion detection area.
Press the SET button to determine the selected point as the
end point of the motion detection area.
It is possible to set up to 4 motion detection areas by
repeating steps 6 and 7.
,Rotate the jog dial to select SENSITIVITY on
the status bar.
Note:Depending on the position of the set detection areas,
the sensitivity indications of the detection areas may be
displayed overlapping each other.
.Move the cross cursor to the motion detection
area to apply the sensitivity using the arrows
button (AB).
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
PAN/
TILT
m,⁄1m.⁄0 
						

							35
⁄2Move the cursor to select a detection mode
using the arrow buttons and rotate the jog dial
to check the radio button next to the selected
detection mode. Press the SET button to deter-
mine the selection.
Refer to page 36for further information about each of the
detection modes.

Move the cursor to the parameter box using the arrows but-
ton (C) to select a masking duration from the following.
1 s/1 m/1 h/24 h

Move the cursor to an area for the settings of VECTOR
using the arrows button (C) and rotate the jog dial to select
an area. Move the cursor to the parameter box of the
selected area using the arrows button (B) to select an
interval time for an object moving between each area from
the following.
--/5 s/10 s/20 s/30 s/40 s/50 s/1 m

Move the cursor to the parameter box of each area using
the arrows button (B) and rotate the jog dial to select a
moving duration for an object in each area from the follow-
ing.
--/5 s/10 s/20 s/30 s/40 s/50 s/1 m
⁄3Press the SET button or the PLAY/PAUSE but-
ton to start searching and display the results
of the VMD search.
Up to 200 results will be displayed. (When 200 results are
listed, searching will stop.)
Notes:
• It may take some time until the search results are dis-
played.
• It is possible to stop searching by pressing the STOP
button.
⁄4Rotate the jog dial to select a result to be dis-
played.
It is possible to turn the page by rotating the shuttle ring.
⁄5Press the PLAY/PAUSE button to start play-
back.
The LISTED indicator and the indicator on the PLAY/PAUSE
button will light and playback of the selected recording will
start.
Note:It is possible to skip from the playback point to the
listed time (motion detected time) by rotating the jog
dial when the LISTED indicator is lit.
To return to normal playback, press the LISTED button.
⁄6Press the STOP button to stop playback.
The indicator on the PLAY/PAUSE button will go off and
playback will be stopped.
Live images will be displayed on monitor 2 and the VGA
monitor.
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
⁄6⁄3
⁄5
⁄2⁄2
⁄3⁄2
⁄4
PAN/
TILT
VECTOR
 ANY AREA
MASKING DURATION
SET : [SET]    SEARCH : [PLAY]    CANCEL : [ESC]
20s
20s 20s 20s 20s20s 20s
 VMD SEARCH
 DURATION
24h
ABCD
ABCD
TIME&DATE
01ch
01ch
01ch
01ch
01ch
01ch
01ch
01chCAM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
TIME&DATE    SEARCH    REC EVENT    SEARCH    VMD    SEARCH    MARK
VMD SEARCH
TOTAL 25.APR.03*12:34:56 AM  25.APR.03*12:34:56 AM12345
TIME&DATE
01ch
01ch
01ch
01ch
01ch
01ch
01ch
01chCAM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
TIME&DATE    SEARCH    REC EVENT    SEARCH    VMD    SEARCH    MARK
VMD SEARCH
TOTAL 25.APR.03*12:34:56 AM  25.APR.03*12:34:56 AM12345 
						

							36
Any motion will be detected anywhere in the A, B, C, D
areas.
Note:In the ANY AREA mode, it is possible to set the
masking duration. When the masking duration is set,
motion will be ignored for a certain period (set duration
as the masking duration) in the same area. It is conve-
nient to set the masking duration to make the subject
period shorter in case it is necessary to search an
extended time range or when searching through many
results.

It will be subject to listing if an object moves within the set
time to the other detection areas in the set order.
The following is an example.
Motion is detected in area B within 10 seconds after being
detected in area A.
Motion is detected in area C within 20 seconds after being
detected in area B.
Motion is detected in area D within 10 seconds after being
detected in area C.
When all of the above have occurred, an event action will
be performed.

It will be subject to listing if an object keeps moving for the
set period in the detection area. For example, in case of the
following settings; 10 sec. for areas A and B, 20 sec. for
area C and 30 sec. for area D:
An event action will be performed when an object keeps
moving longer than the set period in the specified detection
area.
Important:
• When images to be searched are recorded with a low
recording rate, the DURATION mode may not work cor-
rectly.
• It may take some time to search according to the con-
tents of the recorded images.To delete the motion detection
area
zRotate the jog dial to select DELETE AREA
on the status bar. 
Note:To delete all the motion detection areas, select
DELETE ALL AREA and press the SET button.
xMove the cursor to the motion detection area
to be deleted using the arrows button and
press the SET button.
The selected area will be deleted.
 Detection Mode
Set how to detect motion in the set motion detection area.
There are 3 detection modes as follows:
Important:
It is impossible to set two or more detection modes
simultaneously.

It will be subject to listing if motion is detected in any of
the set motion detection areas.
AB
CD
AB
CD
10 s
10 s
20 s
AB
CD
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
zx
x
PAN/
TILT 
						

							37
 Search for a marked point and
play from that point (Marking
search)
Display the recording time of the recorded images with a
marked point in a list or a thumbnail and select the desired
recording time to play. Refer to page 24for further informa-
tion about marking.
zPress the SEARCH button repeatedly until the
marking list window is displayed.
The result list of the marking search will be displayed on
monitor 2 and the VGA monitor.
Use the arrows button (CD) to switch between displaying
the list window and the thumbnail window alternately.To delete all displayed marking lists, press the camera
selection buttons [1] and [2] simultaneously for 2 seconds
or more when displaying the marking list window.
xRotate the jog dial or the shuttle ring to select
the desired marked time.
cPress the PLAY/PAUSE button.
The LISTED indicator and the indicator on the PLAY/PAUSE
button will light, and playback of a recorded image from the
selected marked time will start.
Notes:
• It is possible to skip from the playback point to the list-
ed time (marked time) by rotating the jog dial when the
LISTED indicator is lit.
To return to normal playback, press the LISTED button.
• It is possible that some recorded images with marked
points may have been deleted by overwrite recording
or the delete function.
vPress the STOP button.
The indicator on the PLAY/PAUSE button will go off and
playback will be stopped.
Live images will be displayed on monitor 2 and the VGA
monitor.
R
2
R
1
LOGOUT
MONITOR1
MONITOR2
5
9
2
6
10/0
14 13
3
7
11
SHIFT SEQ
COPYDISK SELECT
EL-ZOOM
TEXT
LOGOUT
4
8
12
OSD
MARK
1
15 16BUSY316
REV FWDSTOPPLAY PAUSEREC - REC STOP
SEARCH
SETUP
/ESCPAN/TILTSLOWA-B
REPEATGOTO
LAST
LISTED ZOOM/
FOCUS
IRIS
PRESET
/AUTO
SET
–
+
PAN/
TILT
xxzz
cv
TIME&DATE
01ch
01ch
01ch
01ch
01ch
01ch
01ch
01chCAM REC EVT TEXT
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
TIME&DATE    SEARCH    REC EVENT    SEARCH    VMD    SEARCH    MARKTOTAL 25.APR.03*12:34:56 AM  25.APR.03*12:34:56 AM100
TIME&DATE
01ch
01ch
01ch
01ch
01ch
01ch
01ch
01chCAM REC EVT TEXT
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
TIME&DATE    SEARCH    REC EVENT    SEARCH    VMD    SEARCH    MARKTOTAL 25.APR.03*12:34:56 AM  25.APR.03*12:34:56 AM100
TIME&DATE
01ch
01ch
01ch
01ch
01ch
01ch
01ch
01chCAM REC EVT TEXT
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
25.APR.03*12:34:56 AM
TIME&DATE    SEARCH    REC EVENT    SEARCH    VMD    SEARCH    MARKTOTAL 25.APR.03*12:34:56 AM  25.APR.03*12:34:56 AM100
⇔ 
						

							38
MONITOR LIVE IMAGES
It is possible to display live images on a single screen or a
multi-screen.
On a single sequential display (It is also possible that dis-
played images from cameras will be switched automatical-
ly)
 Displaying Live Images on a
Single Screen
zPress the MONITOR1/MONITOR2 button to
select the monitor.
When monitor 1 is selected, the indicator will light.
When monitor 2 or the VGA monitor is selected, the indica-
tor will not light.
xPress a camera selection button 
(1 - 16 for the WJ-HD316, 1 - 9 for the WJ-
HD309) to select a camera.
Live images from the selected camera will be displayed
and the respective camera selection button will light green
or blue.
When monitor 2 is selected, live images will be displayed
on the VGA monitor.
 Electronic Zoom
When displaying a single screen, zooming in on the dis-
played image is possible.
Electronic zoom is available only on the selected monitor.
When the MONITOR1/MONITOR2 indicator is lit (the moni-
tor 1 is selected), electronic zoom works only on monitor 1.
zPress the SHIFT button when monitoring live
images on a single screen.
The SHIFT indicator will light.
xPress the EL-ZOOM button to enlarge the dis-
played image.
The displayed image will be displayed with x2 zoomed
size.
Zooming level will change each time the EL-ZOOM button
is pressed.
x2 →x4 →OFF
Notes: 
• When an image is zoomed in on (x2 or x4), it is possible
to move the zoomed image using the arrows button.
• When any indicator of PAN/TILT, ZOOM/FOCUS, IRIS,
PRESET/AUTO is lit, it is impossible to use the EL-
ZOOM function.
R
2 RMONITOR1
MONITOR21
5
9
13
2
6
10/0
14
3
7
11
15
4
8
12
16
SEQ SHIFT OSD
STOPPLAY PAUSEREC - REC STOP
ZOOM/
FOCUS
TEXTCOPYDISK SELECT
EL-ZOOM
MARK
LOGOUTIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWD
PAN/TILTSLOW
[WJ-HD316]
LOGOUT
R
2 RMONITOR1
MONITOR21
4
7
2
5
8
0
3
6
9
TEXT SEQ SHIFT OSDZOOM/
FOCUSCOPYDISK SELECT
EL-ZOOM
MARKIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWDSTOPPLAY PAUSEREC - REC STOP
PAN/TILTSLOW
[WJ-HD309]
PAN/
TILT
PAN/
TILT
zx
zx
R
2 RMONITOR1
MONITOR21
5
9
13
2
6
10/0
14
3
7
11
15
4
8
12
16
SEQ SHIFT OSD
STOPPLAY PAUSEREC - REC STOP
ZOOM/
FOCUS
TEXTCOPYDISK SELECT
EL-ZOOM
MARK
LOGOUTIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWD
PAN/TILTSLOW
[WJ-HD316]
LOGOUT
R
2 RMONITOR1
MONITOR21
4
7
2
5
8
0
3
6
9
TEXT SEQ SHIFT OSDZOOM/
FOCUSCOPYDISK SELECT
EL-ZOOM
MARKIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWDSTOPPLAY PAUSEREC - REC STOP
PAN/TILTSLOW
[WJ-HD309]
PAN/
TILT
PAN/
TILT
zx
zx 
						

							39
 Displaying on a Multi-screen
It is possible to display images on a multi-screen (4, 7, 9,
10, 13, 16 for the WJ-HD316, 4, 7, 9 for the WJ-HD309).
zPress the MONITOR1/MONITOR2 button to
select the monitor.
When monitor 1 is selected, the indicator will light.
When monitor 2 is selected, the indicator will not light.
xPress the SHIFT button.
The SHIFT indicator will light.
cPress a camera selection button 1 - 6 (1 - 3 for
the WJ-HD309) to select a desired multi-
screen.
Camera selection button 1: 4-split screen
Camera selection button 2: 7-split screen
Camera selection button 3: 9-split screen
Camera selection button 4: 16-split screen (Only for the WJ-
HD316)
Camera selection button 5: 10-split screen (Only for the WJ-
HD316)
Camera selection button 6: 13-split screen (Only for the WJ-
HD316)The camera selection buttons respective to the live images
displayed on a multi-screen will light green or blue.
When monitor 2 is selected in step 1, live images will also
be displayed on the selected multi-screen on the VGA mon-
itor.
To display on a single screen
Press the SHIFT button. The SHIFT indicator will go off.
Press any of the camera selection buttons.
Live images will be displayed on a single screen.
When displaying on a 4-split screen
Each time the camera selection button 4 is pressed, the
displayed camera channels will be changed as follows:
WJ-HD316: 1-4 CH – 5-8 CH – 9-12 CH – 13-16 CH
WJ-HD309: 1-4 CH – 5-8 CH – 9 CH
When displaying on a 9-split screen
Each time the camera selection button 9 is pressed, the
displayed camera channels will be changed as follows:
Only for the WJ-HD316: 1-9 CH – 10-16 CH
R
2 RMONITOR1
MONITOR21
5
9
13
2
6
10/0
14
3
7
11
15
4
8
12
16
SEQ SHIFT OSD
STOPPLAY PAUSEREC - REC STOP
ZOOM/
FOCUS
TEXTCOPYDISK SELECT
EL-ZOOM
MARK
LOGOUTIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWD
PAN/TILTSLOW
[WJ-HD316]
LOGOUT
R
2 RMONITOR1
MONITOR21
4
7
2
5
8
0
3
6
9
TEXT SEQ SHIFT OSDZOOM/
FOCUSCOPYDISK SELECT
EL-ZOOM
MARKIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWDSTOPPLAY PAUSEREC - REC STOP
PAN/TILTSLOW
[WJ-HD309]
PAN/
TILT
PAN/
TILT
zc
x
z
c
x 
						

							40
 Sequential Display
Displayed images from cameras will be switched automati-
cally.
Camera images will be displayed sequentially according to
the settings performed in advance.
zPress the MONITOR1/MONITOR2 button to
select the monitor.
When monitor 1 is selected, the indicator will light.
When monitor 2 is selected, the indicator will not light.
xPress the SHIFT button.
The SHIFT indicator will light.
cPress the SEQ button.
The camera selection button respective to the displayed
image will light green.
To stop sequential display, press the SEQ button.
When trying to display on a single screen or multi-screen
during the sequential display, the sequential display will be
stopped.
When monitor 2 is selected in step 1, the sequential display
will also start on the VGA monitor.
R
2 RMONITOR1
MONITOR21
5
9
13
2
6
10/0
14
3
7
11
15
4
8
12
16
SEQ SHIFT OSD
STOPPLAY PAUSEREC - REC STOP
ZOOM/
FOCUS
TEXTCOPYDISK SELECT
EL-ZOOM
MARK
LOGOUTIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWD
PAN/TILTSLOW
[WJ-HD316]
LOGOUT
R
2 RMONITOR1
MONITOR21
4
7
2
5
8
0
3
6
9
TEXT SEQ SHIFT OSDZOOM/
FOCUSCOPYDISK SELECT
EL-ZOOM
MARKIRIS
PRESET
/AUTO
A-B
REPEATGOTO
LAST
LISTED
SEARCH
BUSYSETUP
/ESC
SET
REV
–+
FWDSTOPPLAY PAUSEREC - REC STOP
PAN/TILTSLOW
[WJ-HD309]
PAN/
TILT
PAN/
TILT