Panasonic Digital Disk Recorders Wj Hd309 Operating Instructions

							111
[Screenshot 4]
The cursor moves to the PRESET in STEP 1.
bRotate the jog dial to select a preset position number
for which image is displayed in STEP 1 from the follow-
ing.
1 - 64:Moves to the selected preset number.
--:Does not move to the preset position.
nSelect DWELL in STEP 1 using the arrows button.
[Screenshot 5]
The cursor moves toDWELL in STEP 1.
mRotate the jog dial to select an interval time to go to the
next sequential step from 1 - 30 seconds (in 1 second
intervals).
The sequence step is skipped when 0 s is selected.
Repeat steps 2 and 7 to set for the other sequence
steps.
,Move the cursor to OK using the arrows button and
press the SET button.
→The settings for the sequential display are set and
the sequence setting menu closes.
Note:If you move the cursor to CANCEL in step 8 and
press the SET button, the setting will be canceled
and the sequence setting menu will be closed.
8Sequence Timing
Select an image switching method from the following.
INT:Switches images according to the settings for the live
sequence.
EXT:Switches images by signals from an external device.
MON 2:Match with the image switching timing of the live
sequence on monitor 2.
8Auto Skip
Select ON of OFF to determine whether or not to skip the
camera channel without supplying the video input signal
because it is not connected, etc.
ON:Skips a channel if it is not connected.
OFF:Displays a black screen for a channel not connected.
8Login Screen
Select a camera image to be displayed during the login
procedure from the following.
CAM1 - 16:Displays an image from the selected camera
channel.
QUAD1 - 4:Displays images from camera channels 1 - 4
on a 4-split screen.
QUAD5 - 8:Displays images from camera channels 5 - 8
on a 4-split screen.
QUAD9 (only for the WJ-HD309):Displays an image from
camera channel 9 on the upper left area on a 4-split
screen.
QUAD9 - 12 (only for the WJ-HD316):Displays images
from camera channels 9 - 12 on a 4-split screen.
QUAD13 - 16 (only for the WJ-HD316):Displays images
from camera channels 13 - 16 on a 4-split screen.
7SCREEN:Displays images from camera channels 1 - 7 on
a 7-split screen.
9SCREEN (only for the WJ-HD309):Displays an image
from camera channel 1 - 9 on the upper left area on a
9-split screen.
9SCREEN1 - 9 (only for the WJ-HD316):Displays images
from camera channels 1 - 9 on a 9-split screen.
9SCREEN10 - 16 (only for the WJ-HD316):Displays
images from camera channels 10 - 16 on a 9-split
screen.
10SCREEN (only for the WJ-HD316):Displays images
from camera channels 1 - 10 on a 10-split screen.
13SCREEN (only for the WJ-HD316):Displays images
from camera channels 1 - 13 on a 13-split screen.
16SCREEN (only for the WJ-HD316):Displays images
from camera channels 1 - 16 on a 16-split screen.
--:No camera image will be displayed (black screen)
8Secret View
The secret view is a function to display a black screen on
monitor 1 when camera images are displayed with a single
screen on monitor 2. Select ON or OFF to determine
whether to enable or disable the secret view function.
ON:Enables the secret view function. (Camera images dis-
played with a single screen on monitor 2 will be dis-
played while monitor 1 has a black screen.)
OFF:Disables the secret view function.
EventScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
Monitor 1
Monitor 2
 Live Sequence Sequence Timing Auto Skip Login Screen Secret View
SETUP
INTOFFOFFCAM1
OKCANCEL
1
2
3
4
1-4
5-8
9-12
13-161
1
64
5
--
--
--
--2s
2s
2s
2s
2s
2s
2s
2s--
--
--
--
--
--
--
--2s
2s
2s
2s
2s
2s
2s
2s 9
10
11
12
13
14
15
161-8
9-16
11
12
1-4
5-8
9-12
13-16STEP
1
2
3
4
5
6
7
8CAMDWELLSTEP CAMPRESETDWELLPRESET
EventScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
Monitor 1
Monitor 2
 Live Sequence Sequence Timing Auto Skip Login Screen Secret View
SETUP
INTOFFOFFCAM1
OKCANCEL
1
2
3
4
1-4
5-8
9-12
13-161
1
64
5
--
--
--
--2s
2s
2s
2s
2s
2s
2s
2s--
--
--
--
--
--
--
--2s
2s
2s
2s
2s
2s
2s
2s 9
10
11
12
13
14
15
161-8
9-16
11
12
1-4
5-8
9-12
13-16STEP
1
2
3
4
5
6
7
8CAMDWELLSTEP CAMPRESETDWELLPRESET 
						

							112
[Monitor 2] Switcher function of monitor 2
Perform the settings for the switcher function of monitor 2.
8Live Sequence
The settings for Live Sequence are the same as for
Monitor1. Refer to page 110for further information.
8Sequence Timing
The settings for Sequence Timing are the same as for
Monitor1. Refer to page 111for further information.
Notes:
•Select EXT when an external device that can transmit
a sequence signal is connected.
•The sequence changeover I/O (pin no.21) of the
ALARM/CONTROL connector on the rear panel will
supply signals when INT is selected and will receive
signals when EXT is selected.
8Auto Skip
The settings for Auto Skip are the same as for Monitor1.
Refer to page 111for further information.
8Login Screen
The settings for Login Screen are the same as for
Monitor1. Refer to page 111for further information.
EventScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
Monitor 1
Monitor 2
 Live Sequence Sequence Timing Auto Skip Login Screen
SETUP
INTOFFCAM1 
						

							113
Perform the display settings for monitors 1 and 2 connected
to the unit.
OSD Setup
Perform the On Screen Display settings for monitor 1 and
monitor 2 such as the settings of camera titles or the set-
tings of the time display position.
8Camera Title
Perform the settings for the camera title. It is possible to
display a camera title on the monitor 1/monitor 2, and
record it as a part of the recorded image (page 98). Do the
following to set the camera title.
[Screenshot 1]
Start operation from the OSD Setup menu.
zMove the cursor to Camera Title using the arrows but-
ton (C D) and press the SET button.[Screenshot 2]
The camera title pop-up window will be displayed.
xMove the cursor to CAM1 using the arrows button.
[Screenshot 3]
The cursor moves to  CAM1.
cSelect a character to be entered by rotating the jog dial.
Up to 16 characters can be entered.
vMove the cursor to the right side of the entered charac-
ter using the arrows button. 
Repeat steps 3 and 4 to enter the camera title.
Notes:
•To correct the entered characters, move the cursor
to the character to be corrected and press the
STOP button to delete it. Enter a correct character
after deleting.
•To copy the camera title that has been set for
another camera channel, follow the procedure
below.
1. Move the cursor to CAM 1 in step 2 on the pre-
vious page and press the SET button. The fol-
lowing screen will be displayed.
2. Select the camera channel for which the cam-
era title is to be copied by rotating the jog dial.
 [Display]
ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
OSD Setup
Monitor 1
Monitor 2
Event
SETUPL-UPPERR-LOWERWHITE
 Camera Title Time & Date Display Position  Camera Title Display Position Line Color on the Multi Screen
ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
OSD Setup
Monitor 1
Monitor 2
Event
SETUPL-UPPERR-LOWERWHITE
 Camera Title Time & Date Display Position  Camera Title Display Position Line Color on the Multi Screen
OKCANCELCAM8 CAM7
CAM6
CAM5
CAM4
CAM3
CAM2
CAM1
CAM8 CAM7
CAM6
CAM5
CAM4
CAM3
CAM2
CAM1ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
OSD Setup
Monitor 1
Monitor 2
Event
SETUPL-UPPERR-LOWERWHITE
 Camera Title Time & Date Display Position  Camera Title Display Position Line Color on the Multi Screen
ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
OSD Setup
Monitor 1
Monitor 2
Event
SETUPL-UPPERR-LOWERWHITE
 Camera Title Time & Date Display Position  Camera Title Display Position Line Color on the Multi Screen
OKCANCELCAM8 CAM7
CAM6
CAM5
CAM4
CAM3
CAM2
CAM1
ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
OSD Setup
Monitor 1
Monitor 2
Event
SETUPL-UPPERR-LOWERWHITE
 Camera Title Time & Date Display Position  Camera Title Display Position Line Color on the Multi Screen
ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
Common Setup
Monitor 1
Monitor 2
Event
SETUPL-UPPERR-LOWERWHITE
 Camera Title Time & Date Display Position  Camera Title Display Position Line Color on the Multi Screen
OKCANCELCAM8 CAM7
CAM6
CAM5
CAM4
CAM3
CAM2
CAM1
CAM8 CAM7
CAM6
CAM5
CAM4
CAM3
CAM2
CAM1  Copy Another Camera Title
O K
CAM2
CANCEL 
						

							114
3. Move the cursor to OK using the arrows button
and press the SET button. The camera title will
be copied.
•The following characters can be entered for a cam-
era title:
0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P
Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r
s t u v w x y z À Ä Â Æ Ç É Ì Ñ Ò Ö Ù Ü Ø ß à á â ä
å æ ç è é ê ë ì í î ï ñ ò ó ô ö ù ú ü ø < > = ? ” # & ( )
* + , - . / : ; SP
[Screenshot 4]
The camera title is entered.
bPress the arrows button to move the cursor to OK and
press the SET button.
→The camera title will be set and the setting window
of the camera title will be closed.
Notes:
•If you move the cursor to CANCEL in step 5 and
press the SET button, the setting will be canceled
and the setting window of the camera title will be
closed.
•It is possible to set Camera Title [Display] to dis-
play a camera title on monitor 2 and Camera Title
[Embedded] to embed/display a camera title on
monitor 1 individually using a PC via a network.
Refer to the Network Setup Instruction (PDF) for fur-
ther information.
8Time & Date Display Position
Select a time and date display position from the following.
L-UPPER:Displays the time at the upper left of the screen.
R-UPPER:Displays the time at the upper right of the
screen.
L-LOWER:Displays the time at the lower left of the screen.
R-LOWER:Displays the time at the lower right of the
screen.Notes:
•When setting the time and date to be recorded together
with images, the time display will be recorded in the
selected position.
•Refer to page 98for further information about
Embedded REC (Time & Date).
8Camera Title Display Position
Select a camera title display position from the following.
L-UPPER:Displays the camera title at the upper left of the
screen.
L-LOWER:Displays the camera title at the lower left of the
screen.
R-UPPER:Displays the camera title at the upper right of
the screen.
R-LOWER:Displays the camera title at the lower right of
the screen.
CENTRE:Displays the camera title at the centre of the
screen.
Note:When setting the camera title to be recorded togeth-
er with images, the time display will be embedded in
the selected position.
Refer to page 98for further information about
Embedded REC (title).
8Line Colour on the Multi Screen
Select a line colour from the following.
WHITE:Displays white lines.
GREY:Displays grey lines.
BLACK: Displays black lines.
[Monitor 1] Settings on monitor 1 display
Select ON and OFF whether or not to display the time, cam-
era title and alarm display on monitor 1.
8Time & Date Display
Select ON and OFF whether or not to display the time.
ON:Displays time.
OFF:Does not function.
ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
OSD Setup
Monitor 1
Monitor 2
Event
ON Time & Date Display   Camera Title  Display  Alarm DisplayON ON
ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
OSD Setup
Monitor 1
Monitor 2
Event
SETUPL-UPPERR-LOWERWHITE
 Camera Title Time & Date Display Position  Camera Title Display Position Line Color on the Multi Screen
OKCANCELCAM8 CAM7
CAM6
CAM5
CAM4
CAM3
CAM2
CAM1
CAM8 CAM7
CAM6
CAM5
CAM4
CAM3 CAM1
ENTRANCE
ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
OSD Setup
Monitor 1
Monitor 2
Event
SETUPL-UPPERR-LOWERWHITE
 Camera Title Time & Date Display Position  Camera Title Display Position Line Color on the Multi Screen
OKCANCELCAM16 CAM15
CAM14
CAM13
CAM12
CAM11
CAM10
CAM9
CAM16 CAM15
CAM14
CAM13
CAM12
CAM11 CAM9
CAM10 
						

							115
8Camera Title Display
Select ON and OFF whether or not to display the camera
title.
ON:Displays the camera title.
OFF:Does not function.
8Alarm Display
Select ON and OFF whether or not to activate the alarm dis-
play at an event occurrence.
ON:Displays the alarm display at an event occurrence.
OFF:Does not function.
[Monitor2] Settings on monitor 2 display
Perform the display settings for monitor 2 such as the dis-
play mode (task bar style), time display position on/off,
camera title display position, etc.
The following explain the settings for monitor 2 and the VGA
monitor such as the display mode (task bar style), time dis-
play position, camera title display ON/OFF, etc.
8Display Mode
Select a display mode (task bar style) from the following.
Refer to page 11for further information about the task bar.
MODE 1:Select [MODE 1] for the display mode.
MODE 2:Select [MODE 2] for the display mode.
MODE 3:Select [MODE 3] for the display mode.
8T & D and Status Display Position
When selecting MODE 1, select the position of the time and
date display and the status from the following.
UPPER:Displays them in the upper part of the screen.
LOWER:Displays them in the lower part of the screen.
8Camera Title Display
Select ON and OFF whether or not to display the camera
title.
ON:Displays the camera title.
OFF:Does not function.
ScheduleSystemDisplayCommSwitcherSETUP MENULIVEMaintenanceRecording
OSD Setup
Monitor 1
Monitor 2
Event
MODE 1 Display Mode   T&D and Status Display Position Camera Title  DisplayON LOWER 
						

							116
It is necessary to adjust the communication speed and use
the same communication protocol with external devices
such as a controller when connecting those external
devices to the DATA port or the SERIAL connector
(RS232C).
It is also necessary to perform the settings for the network
such as the IP address and the gateway address when
operating this unit a PC via a network such as a LAN.
These are the descriptions of how to perform the required
settings for communication with external devices.
[Camera Control] Settings for the communi-
cation method and the cable compensation
for camera control
Select a communication method for each camera channel
to control cameras from the following.
COAX:Controls camera with the coaxial communication
(CAM 1 - 8 CH are available for the WJ-HD316, CAM 1 -
6 CH are available for the WJ-HD309)
PSD:Controls camera with the PS·Data. (CAM 9 - 16 CH
are available for the WJ-HD316, CAM 7 - 9 CH are
available for the WJ-HD309)
RS485:Controls camera with the RS485 communication.
(CAM 1 - 16 CH are available for the WJ-HD316, CAM 1
- 9 CH are available for the WJ-HD309)
OFF:Does not control camera (CAM 1 - 16 CH are avail-
able) 
Notes:
•Perform settings according to the cameras connected
to this unit.
•CAM 9-16 control 4 cameras each (only for the WJ-
HD316).
•When using the coaxial communication to control cam-
eras, connect cameras to the VIDEO IN connectors 1 -
8 for the WJ-HD316 (1 - 6 for the WJ-HD309) (coaxial
communication compatible). When controlling cameras
connected to other VIDEO IN connectors with coaxial
communication, use a coaxial communication unit (WJ-
MP204). In this case, select PSD for the communica-
tion method for the camera channels to be controlled
through the coaxial communication unit.•To prevent operation mistakes, set the unused camera
channels to off.
It is possible to compensate for the video signal trans-
mission loss from the camera when using the VIDEO IN
connector 1 - 8. (cable compensation)
Perform the settings for the cable compensation
according to the length of cable used.
S:When the length of cable used is shorter than 500 m
M:When the length of cable used is longer than 500 m
and shorter than 900 m
L:When the length of cable used is longer than 900 m
and shorter than 1 200 m
Notes:
•Use 5C-2V cables for the cable compensation.
•Perform the settings for the cable compensation prop-
erly according to the cable length. Otherwise camera
pictures may not be displayed/recorded correctly.
[PS.Data Setup] Settings for the PS·Data 
Perform the following settings for the PS·Data.
8Unit Address (System)
A unit address (System) is a unique number assigning to
PS·Data devices. The addresses must be unique to identify
system devices when connecting multiple devices compati-
ble with PS·Data. Numbers, 001-099, are to be assigned
as the unit addresses to the system devices.
8Unit Address (Controller)
The unit address (controller) is used to control a PS·Data
device connected to this unit. Numbers, 001 - 099 are to
be assigned.
8Cascade
Select ON or OFF whether or not to use the cascade con-
nection.
Set this to ON when connecting two or more units or in the
cascade connection.
ON:Select this when connecting units in the cascade con-
nection.
OFF:Does not function.
[Comm] Settings for communication with other devices
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.Data Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup Type of Camera Control
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8CAM9
CAM10
CAM11
CAM12
CAM13
CAM14
CAM15
CAM16RS485PSD S
S S
S
S
S
S
SCOAX
COAX COAX
COAX
COAX
COAX
COAX
COAXCAM CAM TYPECOMP TYPE
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
SETUP
001
001
1s OFF
1
NONE
8
9600
OFF
  Unit Address(System)  Unit Address(Controller)  Cascade  Baud Rate  Data Bit  Parity  Stop Bit  Retry Timing  Alarm Data  Camera Number Setup 
						

							117
8Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
2 400/4 800/9 600/19 200/38 400 bps
8Data Bit
It is impossible to change the value for this setting.
8 bit
8Parity
Select a method to check a transmission error at communi-
cation from the following.
NONE:No parity check
EVEN:Even parity
ODD:Odd parity
8Stop Bit
Select a stop bit from the following.
1 bit/2 bit
8Retry Timing
Select a retransmission interval for when data reception is
not confirmed from the following.
OFF/100 ms/200 ms/400 ms/1 000 ms
8Alarm Data
Select a method to inform the connected controller of an
event occurrence from the following.
OFF:Does not function.
0 s:Informs the controller every time an event is detected.
1 s/5 s:Informs the controller when a specified time has
passed after detecting an event.
8Camera Number Setup
It is possible to assign a number to each camera channel to
operate cameras using the controller compatible with
PS·Data.
Do the following to assign numbers to the camera chan-
nels.
[Screenshot 1]
Start operation from the PS·Data Setup menu.
zMove the cursor to Camera Number Setup using the
arrows button (C D) and press the SET button.[Screenshot 2]
The Camera Number Setup pop-up window will be dis-
played.
xMove the cursor to a desired CAM No. of CAM PORT
using the arrows button.
[Screenshot 3]
The cursor will move to the selected CAM No. of CAM
PORT.
cSelect a camera number by rotating the jog dial.
Repeat steps 2 and 3 to assign camera numbers to the
other CAM PORT.
vMove the cursor to OK using the arrows button and
press the SET button.
→Camera numbers will be assigned and the Camera
Number Setup menu will be closed.
Note:When you move the cursor to CANCEL in step 4
and press the SET button, the settings will be can-
celed and the Camera Number Setup menu will be
closed.
[RS485 Setup] Settings for RS485
Perform the following settings for RS485.ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
SETUP
001
001
1s OFF
1
NONE
8
9600
OFF
  Unit Address(System)  Unit Address(Controller)  Cascade  Baud Rate  Data Bit  Parity  Stop Bit  Retry Timing  Alarm Data  Camera Number Setup
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
SETUP
001
001
1s OFF
1
NONE
8
9600
OFF
  Unit Adress(System)  Unit Adress(Controller)  Cascade  Baud Rate  Data Bit  Parity  Stop Bit  Retry Timing  Alarm Data  Camera Number Setup
O KCANCEL
CAM NO.CAM PORT CAM NO. CAM PORT
1
2
3
4
5
6
7
89
10
11
12
13
14
15
16009
010
011
012
013
014
015
016  Camera Number Setup
001
002
003
004
005
006
007
008
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
SETUP
001
001
1s OFF
1
NONE
8
9600
OFF
  Unit Adress(System)  Unit Adress(Controller)  Cascade  Baud Rate  Data Bit  Parity  Stop Bit  Retry Timing  Alarm Data  Camera Number Setup
O KCANCEL
CAM NO.CAM PORT CAM NO. CAM PORT
1
2
3
4
5
6
7
89
10
11
12
13
14
15
16009
010
011
012
013
014
015
016  Camera Number Setup
001
002
003
004
005
006
007
008
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup  Baud Rate  Control Camera CH  Data Bit  Parity  Stop Bit
19200
8
1 NONESETUP 
						

							118
8Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
4 800/9 600/19 200 bps
8Control Camera CH
It is possible to assign camera channels to the RS485 ports
1 and 2 as shown below.
[Screenshot 1]
Start operation from the RS485 Setup menu.
zMove the cursor to Control Camera CH using the
arrows button (CD) and press the SET button.
[Screenshot 2]
The Control Camera CH pop-up window will be displayed.
xMove the cursor to a desired cell in the TERM column
using the arrows button.
[Screenshot 3]
The cursor will move to the selected cell in the TERM col-
umn.
cSelect a port by rotating the jog dial.
PORT 1:Control through the RS485 port 1.
PORT 2:Control through the RS485 port 2.
Repeat steps 2 and 3 to assign other camera channels
to be controlled through the RS485 ports.vMove the cursor to OK using the arrows button and
press the SET button.
→Camera channels and ports to be controlled will be
assigned and the Control Camera CH menu will be
closed.
Notes:
•When you move the cursor to CANCEL in step 4
and press the SET button, the settings will be can-
celed and the Camera Number Setup menu will be
closed.
•The unit number of the camera will be congruent
with the camera number.
8Data Bit
The data length for communication will be displayed.
It is impossible to change the value for this setting.
8Parity
Methods to check a transmission error at communication
will be displayed.
It is impossible to change the value for this setting.
8Stop Bit
Number of stop bit will be displayed.
It is impossible to change the value for this setting.
[RS232C Setup] Settings for RS232C
Perform the following settings for RS232C.
8Unit Address(System)
A unit address (System) is a unique number assigned to
each system device. The addresses must be unique to
identify system devices when connecting multiple system
devices.
Numbers, 001-099, are to be assigned as the unit
addresses for the system devices.
8Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
9 600/19 200/38 400 bps
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup  Baud Rate  Control Camera CH  Data Bit  Parity  Stop Bit
19200
8
1 NONESETUP
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup  Baud Rate  Control Camera CH  Data Bit  Parity  Stop Bit
19200
8
1 NONESETUP
O KCANCEL
  Control Camera CHCAMERA
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8CAMERA
CAM9
CAM10
CAM11
CAM12
CAM13
CAM14
CAM15
CAM16TERM
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2TERM
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1 PORT1
PORT1
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup  Baud Rate  Control Camera CH  Data Bit  Parity  Stop Bit
19200
8
1 NONESETUP
O KCANCEL
  Control Camera CHCAMERA
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8CAMERA
CAM9
CAM10
CAM11
CAM12
CAM13
CAM14
CAM15
CAM16TERM
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2
PORT2TERM
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1
PORT1 PORT1
PORT1
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup  Unit Address(System)  Baud Rate  Data Bit  Parity  Stop Bit  Retry Timing
001
8
1OFF NONE
9600 
						

							119
8Data Bit
Select a data length for communication from the following.
7/8 bit
8Parity
Select a method to check a transmission error at communi-
cation from the following.
NONE:No parity check
EVEN:Even parity
ODD:Odd parity
8Stop Bit
Select a stop bit from the following.
1/2 bit
8Retry Timing
Select a retransmission interval for when data reception is
not confirmed from the following.
OFF/100 ms/200 ms/400 ms/1 000 ms
[NW Setup 1] Basic network settings
Perform the following basic network settings to operate this
unit using a PC via a network such as a LAN.
8HTTP Port Number
Specify the HTTP port number to be used to transfer
images from this unit. It is not necessary to change it for
normal use.
8User Authentication
Select ON and OFF whether or not to activate user authenti-
cation at the time of access from a PC to this unit.
When ON is selected, the user authentication (login) win-
dow will be displayed at the time of access from a PC.
The top page will be displayed if the entered user name
and password are registered.
ON:Activates user authentication.
OFF:Does not function.
Note:It is recommended to select ON for the user authenti-
cation for security.
8Host Authentication
Select ON or OFF whether or not to restrict access by IP
addresses at the time of access from a PC to this unit.
When ON is selected, only PCs with registered IP address
can access this unit
ON:Activates host authentication.
OFF:Does not function.
Note:When ON is selected for both the user authentication
and the host authentication, it is possible to operate the
unit only from a registered host. Operable functions will
differ depending on the user level setting of the authen-
ticated user. It is impossible to operate the unit from an
unregistered host.
8Line Speed
The line speed will be displayed.
It is impossible to change the value for this setting.
8Live Video Quality
Image quality level for a live (FQB: high quality) will be dis-
played.
It is impossible to change the value for this setting.
[NW Setup 2] Network connection settings
Perform the following network connection settings to oper-
ate this unit using a PC via a network such as a LAN.
8DHCP
Select ON or OFF whether or not to use the DHCP server.
When obtaining IP addresses, net mask and a gateway
address from the DHCP server, set to ON.
If not, set to OFF and enter those addresses manually.
ON:Uses the DHCP server.
OFF:Does not use the DHCP server.
8IP Address
Enter an IP address when OFF is selected for DHCP.
For this unit, enter 4 units of the decimal number (0-254).
8Subnet Mask
Enter a subnet mask according to the network configuration
when OFF is selected for DHCP.
8Gateway
Enter the gateway address according to the network con-
figuration when OFF is selected for DHCP.
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.Data Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup HTTP Port Number User Authentication Host Authentication Line Speed Live Video QualityFQB AUTO 00080
OFF
OFF
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.Data Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup DHCP IP Address Subnet Mask Gateway DNS
Primary
Secondary
 DDNS
User Name
User Password
Access Interval
 Host Name Domain Name
.
.
..
.
..
.
.
..
..
. .192
255
192
000
000168
255
168
000
000000
255
000
000
000250
000
001
000
000
OFF MANUAL OFF
HD316
localdomain10m 
						

							120
8DNS
Select MANUAL or AUTO to enable searching for an IP
address by its host name using DNS. When OFF is select-
ed for DHCP (no use of the DHCP server), select MANU-
AL and enter the domain name and the DNS server
address. If ON is selected for DHCP (use of the DHCP
server), select AUTO. When DNS is not used, select OFF.
When MANUAL is selected for DNS, enter the DNS server
address for Primary and Secondary.
8DDNS
Select ON and OFF whether or not to use the DDNS
(Dynamic Domain Name Server).
Selecting ON is available only when MANUAL or AUTO is
selected for DNS.
When ON is selected, perform the following.
User Name:Enter the user name registered in DDNS.
Password:Enter the password for the user entered in
User Name.
Access Interval:Select an interval to update DNS from the
following.
10 m/30 m/1 h/6 h/24 h
8Host Name
Enter the host address registered in DDNS.
Enter a host name of no more than 255 alphanumeric char-
acters. Hyphens (-) are also available for the host name.
8Domain Name
Enter the domain name of this unit.
Enter a domain name of no more than 255 alphanumeric
characters. Hyphens (-) are also available for the domain
name.
[NTP Setup] Time adjustment of network
Perform the following settings for time adjustment.
8Time Adjustment
Select ON and OFF whether or not to adjust the time with
reference to the NTP server.
ON:Adjusts time with reference to the NTP server.
OFF:Does not function.
Note:Time adjustment will be performed automatically
when the clock time is inaccurate to within ±5 seconds
from the standard time of the NTP server.
8Time Zone
Set the time zone in accordance with the place of use when
using the NTP server for time adjustment.
8NTP Server Address
Enter the NTP server address when using the NTP server
for time adjustment.
8Refresh Interval
Select an interval of time inquiry to be transmitted to the
NTP server from the following.
1 h/2 h/6 h/12 h/24 h
Important:
Recording will not be performed for around 4 seconds
when changing the present time (accurate to within ±5
seconds) using Time Adjustment.
ScheduleSystemCommSwitcherSETUP MENULIVEMaintenanceRecording EventDisplay
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup Time  Adjustment Time  Zone NTP Server Address Refresh Interval
GMT+11:00OFF
6h
GMT   0 : 00