Panasonic Digital Disk Recorders Wj Hd309 Operating Instructions

41
CONTROL CAMERAS
When displaying live images, the following camera controls
are possible.
• Panning/tilting: Moves a camera horizontally/vertically.
• Zooming: Zooms in/out on images.
• Focus: Adjusts the focus.
• Iris: Adjusts the iris of the lens.
• Preset action: Moves a camera to the preset position
registered in advance.
• Auto function: Moves a camera with an auto function
set in advance.
Notes:
• Controlling cameras is possible only when displaying
images on a single screen.
• Depending on...

42
xUse the arrows button (AB) to adjust the
focus.
Press the arrows button (A) to shift the focus farther.
Press the arrows button (B) to shift the focus nearer.
Auto focus is available by pressing the SET button.
cPress the camera selection button ([1] - [16] for
the WJ-HD316, [1] - [9] for the WJ-HD309)
respective to the controlled camera channel to
quit the focusing operation.
 Iris
Adjusts the iris of the lens.
zPress the IRIS button.
The IRIS indicator will light.
xUse the arrows button (AB) to...

43
 Move a camera to the preset
position
zPress the PRESET/AUTO button.
The PRESET/AUTO indicator will light and the PRESET/
AUTO PAN window will be displayed.
xPress a camera selection button 
([1] - [10/0] for the WJ-HD316, [1] - [9], [0] for
the WJ-HD309) to select a desired preset posi-
tion.
Pressing the camera selection button [10/0] ([0] for the WJ-
HD309) moves a camera to the home position.
The jog dial can also be used to select a preset position
number by rotating it.
cSelect OK using the...

44
Note:To move the camera to another registered preset
position, press the SET button after selecting a desired
preset position number in step 2. The PRESET/AUTO
PAN window will not close and it is possible to select
another preset number.
 Auto Function (Auto Pan, etc)
Moves a camera with an auto function set in advance.
Important:
When monitor 1 is selected, it is impossible to move a
camera with an auto function by performing the follow-
ing steps.
In this case, perform the settings using the setup...

45
ABOUT THE EVENT FUNCTION
The event action will be performed when the following
events occur.
•Motion detection:When motion is detected by the
motion detection function (see below), this is stated as
an event of motion detection.
•Video Loss:When a video signal supply is stopped
because of a cable disconnection or malfunction of a
camera, this is stated as an event of video loss.
•Terminal alarm:When a signal is supplied from an
external device such as a door sensor to the ALARM
terminal, this is...

46
 Alarm Function
 Blinks the ALARM indicator on the front
panel
 Switches from the images displayed on
monitor 1 and monitor 2 to the images from
the location of the alarm occurrence (on a
single screen) Displays the event information in the alarm
display area on monitor 1 and the camera
title display area on monitor 2


 Sounds the buzzer
Contact a system administrator about sounding duration.
 Announces an event occurrence to the con-
nected system device (Alarm Output)
Sends a signal to the...

47
 Cancel the Alarm Action
When an alarm has occurred, this unit will start the alarm
action according to the selected alarm action mode.
To cancel the alarm action, press the ALARM RESET but-
ton.
When ON is selected for Alarm Auto Reset (on the Alarm
Setup menu of Event), the following will be performed
automatically even if the alarm action is not canceled by
pressing the ALARM RESET button on the front panel.
• The ALARM indicator will stop blinking and light steadi-
ly
• The displayed alarm...

48
It is possible to copy (duplicate) manually the images
recorded on the disk area selected with the DISK SELECT
window (page 25) to the HDD copy area or the external
recording device (DVD-RAM disk, DVD-R disk, CD-R disk)
connected to the unit.
It is recommended to make back-up copies on a regular
basis for unexpected situations such as malfunction of the
hard disk.
Manual copy is available during the following.
• While displaying live images
• While pausing playback of recorded images
• When displaying...

49
vSelect the OK button using the arrows button
and press the SET button.
The DATA COPY window will be closed and data copy will
start.
The copy icon will be displayed on the task bar during
copying.
To close the DATA COPY window, select CANCEL using
the arrows button and press the SET button. The setting will
be canceled and the DATA COPY window will be closed.
In the following cases, copying will not start even when you
move the cursor to OK and press the SET button:
• When another user has selected...

50
Perform the settings for the built-in hard disk of the unit, the
optional extension unit and the DVD-RAM disk. These are
the descriptions of how to delete recorded images on the
hard disk and how to format a DVD-RAM disk.
Refer to a system administrator for further information about
the other disks.
 Deletion of recorded images
saved on the hard disk manually
Delete recorded images saved in the normal area or the
event area of the built-in hard disk or the optional extension
unit manually.
By setting...