Panasonic Cz Rtc4cz Rtc3 Operating Instructions Manual

							11(EN)
Changing the Program Timer
To set the weekly program, follow the steps.
1
Select the program you want to 
set in the program confi rmation 
mode, and press [SET]. This enters 
the setting mode of the program 
currently displayed.
* In the program setting mode, [SETTING], 
“hour”, “minute”and “item”  fl ash on the 
display.

2 / 3 / 4
4 1 / 2 / 3 / 4
Program step1
Program step2
2
Set the “hour”. (Program step 1)
Press [▼/▲] to set the “hour”.
Confi  rm the “hour” and press [SET]. This 
enters the program changing mode 
 
(setting of the “minute”).
3
Set the “minute”. (Program step 2)
Press [▼/▲] to set the “minute”.
Confi  rm the “minute” and press [SET]. 
The unit enters 
 (the program pattern 
selection mode).
SET
SET SET SET
CANCEL,DEL
normal remote controller
program check
PROGRAM CANCEL
CANCEL,DEL
CANCEL
PROGRAM
SET,CANCEL,DEL
SET,CANCELProgram Changing hour digits
Changing minute digits
Changing patterns
Selecting copy source
Selecting copy destination
Weekly Program Function 
						

							12(EN)
4
Set the program pattern. (Program step 3)
There are 4 program patterns. 
Pressing [▼/▲] repeats the following display patterns.
ÃÃ
Pattern 1 (Default display)
[▼]
[▼]Pattern 2
[▲]
[▲] Pattern 4[▲][▲]
Pattern 3 [▼][▼] The indoor unit starts operation at the 
programmed time.
The indoor unit starts operation at the 
programmed time and changes the 
temperature settings.
The indoor unit stops operation at the 
programmed time.
The indoor unit changes the 
temperature setting at the 
programmed time.
For Pattern 3 and Pattern 4: Press [/] to change the temperature setting.
5
Select the program pattern and press [SET]. 
The program timer setting is confi rmed and the unit enters the confi rmation mode 
.
Note
  If you press [CANCEL] during the setting, it returns to the program confi rmation 
mode.
  If there is no operation made for 10 minutes during the setting, it returns to the 
normal mode.
In this case, all the settings in progress will be invalid.  
						

							13(EN)
Note
  After deleting, the unit returns to the program confi rmation mode .
   
If you press [CANCEL] during the setting, the unit returns to the program 
comfi rmation mode.
   
If there is no operation made for 10 minutes during the setting, the unit returns to 
the normal mode. To delete the program timer setting, follow the steps below.
1
Press [PROGRAM] to enter the 
program confi rmation mode.

4 1 5 2 / 3
2
Press [▼/▲] to select the day of the 
program you want to delete.
Press [SET] to fi x the day.
3
Press [▼/▲] to select a TIMER No. 
(from 1 to 6).
4
Press [SET] to display the program 
setting mode 
.
5
Press [DELETE] to delete the 
program.
Weekly Program Function
Deleting the Program Timer 
						

							14(EN)
Weekly Program Function
Invalidating the Program Timer
If you want to stopping the program operation for more than 1 week, you can invalidate 
all the timer settings.
Once the timer settings are invalidated, the program will not be operated until the 
invalidation is cancelled.
How to invalidate the program timer 
1.  Press and hold [CANCEL]([TIMER 
OFF]) for more than 2 seconds.
[TIMER OFF] is displayed and the programs will 
be invalidated from the next one.

1
How to cancel the program timer invalidation
1.  Press and hold [CANCEL]([TIMER 
OFF]) for more than 2 seconds.
[TIMER OFF] disappears and the programs will 
be validated from the next one.

1
  If Power Failure Occurred 
If the power recovers in a short time period, the program after the recovered time will 
be valid. 
If more than one hour has passed for power return after power failure, the present time 
information will be lost. In this case, the program will not be operated. 
						

							15(EN)
You can duplicate the preset program by day.
  Select the copy source.
1
If [PROGRAM]([COPY]) is pressed 
in program checking mode 
, it 
enters the copy mode (Selecting 
the copy source 
) of the program 
timer. 
While in the copy mode of the program 
timer, [SETTING] and  (day) of the copy 
source fl ash on the display.

1 2 / 4 3 / 4
2
Press [▼/▲] to select the day of the 
copy source.
Select the copy destination.
3
If [SET] is pressed in the mode of 
selecting the copy source 
, it 
enters the copy mode (Selecting the 
copy destination 
) of the program 
timer.
4
Press [▼/▲] to select the day of the 
copy destination. Then, press [SET] 
to complete copying and return to 
the program checking mode.
Weekly Program Function 
Note
The program will be overwritten if the preprogrammed day is selected as a copy 
source.
Duplicating the Program Timer 
						

							16(EN)
Before Asking Repair Work
Before asking repair work, please check the following. 
Trouble Possible Cause/Remedy
“ERROR” is displayed 
when the minute digits are 
entered.If there is another TIMER No. which has the program of the same 
time and same day, you cannot overlap the setting.
The set data is not stored.The stored programs are automatically sorted by the time. Check if 
the data is stored in the other TIMER No.
Program does not 
function.Check if the time indication is not “– – : – –”.
When the time is invalid, the program is also invalid.
Check the remote controller prohibition inside.
In that case, the program is invalid.
Weekly Program Function 
						

							17(EN)
Outing Function
Outing function is a function that prevents the room temperature from 
increasing too much (or decreasing too much) when no one is in the room.
An air conditioner works automatically if this function is set effective.
  
  
  
  
•  
  
•  
• •  
 
• 
 
  
 
 
A remote controller may lose outing function operation information when it is cut for 
more than 24 hours during the outing function operation by electricity. It reverts from 
the blackout, and an air conditioner does not drive in outing function when operation 
is started. At this time, an air conditioner does not stop at outing function. 
						

							18(EN)
1
Press and hold [Ventilation] for more 
than 2 seconds to display 
the upper limit temperature setting 
screen.
[SETTING], ,  and the upper limit 
temperature start fl ashing.
(The default value of the upper limit 
temperature is 38 °C.)
1 2 / 3 2 / 3
Ã
2      
Ã
3
2
Press [/] to select the upper 
limit temperature, and press [SET] 
to fi x the value. The lower limit 
temperature setting screen is 
displayed.
3
Press [/] to select the lower limit 
temperature, and press [SET] to 
fi x the value. The outing function 
setting is completed. 
(The default value of the lower limit 
temperature is 10 °C.)
*  The unit returns to the normal mode if [CANCEL] is pressed or there is no operation 
made for 3 minutes during the setting. In this case, all the settings in progress will be 
lost.
Canceling the outing function
1.  Press and hold [Ventilation] for more 
than 2 seconds while the outing 
function is set.

1
Outing Function
Setting the Outing Function 
						

							19(EN)
This function leads you to a comfortable sleep and changes the room temperature 
during your sleep.
•  You can set the off timer every one hour from 1 to 10 hours.
  Display of remote control unit (during the time setting)
Sleeping function 
indication
Off time
In case the present time is 23:00.
Operating time
  Display of remote control unit (during sleeping function setting)
Ã
Sleeping function 
indication
*  If no operation is made for 3 minutes, the time setting mode will be automatically 
fi nished.
Sleeping Function 
						

							20(EN)
Ex. In case of 7 hours timer
1
Press [Sleeping].
•  Each time the button is pressed, the 
indication changes in the following order.
(every one hour)
(Press [CANCEL] to stop the time setting.)

211
2
Press [SET].
•  The sleeping operation starts.
  When the off time comes:
•  The indoor unit stops.
*  The temperature returns to the setting at the time when sleeping function 
operation started.
To cancel the sleeping function operation
1. Press [Sleeping].* The temperature setting remains at the time 
cancelled.

1
•  The following buttons also cancel the sleeping function operation.
[Start/Stop] button
Stops the indoor unit after the sleeping function operation is cancelled.
[Mode select] button
Changes the operation mode after the sleeping function operation is cancelled.