Panasonic Cz Rtc4cz Rtc3 Operating Instructions Manual

							21(EN)
  If [Sleeping] button does not work.
Or, in the case of operation not being started even if [SET] is pressed.
Check the following table.
ItemDisplay of the remote control unit
(Lighting/fl ashing indication)Contents
1
 The Error indication fl ashes 
(for several seconds).The clock is not set.
2
 “This function is not available” indication 
lights up (for several seconds).When the operation mode is set to AUTO or 
FAN, this function is not available.
3
 Centralized control indication fl ashes 
(for several seconds).The centralized control device is prohibited 
from starting/stopping the unit or changing the 
temperature setting.
The sleeping function operation will be cancelled in the following cases:
1:  When the unit is operated to stop or change the temperature setting by the other remote 
control unit or centralized control device.
2:  When the unit is operated to stop or change the temperature setting with the weekly program 
function / outing function.
3:  When the centralized control unit is prohibited from stopping the unit or changing the 
temperature setting.
Note
Trouble Possible Cause/Remedy
The temperature setting does not 
decrease (increase).The temperature over the upper or lower limit or each operation 
mode cannot be set.
Operation under the sleeping function 
does not fi nish.Note if you change the time after the sleeping function started. The 
operation does not fi nish until it reaches to the set starting time. 
						

							22(EN)
ECONAVI Function
This function is available by attaching an optional ECONAVI sensor.
The ECONAVI sensor detects human activity and conserves energy based on the 
activity level. 
Overview of the ECONAVI function
High activity• Cooling:  Target temperature is the same as the set temperature.
• Heating:  Target temperature is 1 °C lower than the set 
temperature.
Low activity• Cooling:  Target temperature is 1 °C higher than the set 
temperature.
• Heating:  Target temperature is the same as the set temperature.
No one in the room No one in the room for 20 minutes
• Cooling:  Target temperature is 2 °C higher than the set 
temperature.
• Heating:  Target temperature is 2 °C lower than the set 
temperature.
No one in the room for 3 hours
• Cooling:  Cooling will stop and the unit will be in fan only mode.
• Heating:  Heating will stop and the unit will be in fan only mode. * When the sensor 
detects movements in 
the room which have 
been empty, it will 
resume operation to 
match with the activity 
level.
Note
  Even when target temperature is changed through the ECONAVI function, the set 
temperature shown in the remote controller does not change.
   Even when Cooling/Heating is changed to Fan through the ECONAVI function, 
the operation mode shown in the remote controller will still be Cooling/Heating.
  It is possible to choose from the following options for the operation to be 
performed after a lapse of 3 hours since the room has been empty.
•  Operates in the Fan mode only.
•  Stops and resumes operations after human movements are detected.
• 
Stops and will not resume operations even after human movements are detected.
•  Continues to operate in the current mode.
If you need to do so, please contact the dealer. 
						

							23(EN)
ECONAVI Function
Using the remote controller, you can switch the ECONAVI function ON/OFF.
1
Press [ECONAVI] to ON the 
ECONAVI function.
* When ECONAVI is enabled,  
will appear.

1 / 2
2
Press [ECONAVI] to OFF.
* When the indoor unit is stopped,  will disappear.
ON/OFF setting of ECONAVI function
Note
  Turn the ECONAVI function OFF if:
-  You want to maintain the room temperature at a set temperature.
-  You want to keep air conditioner running while nobody is in a room.
-  The sensor fails.
-  Only infants, babies, or people only with disabilities are in the room.
 WARNING
Do not use the ECONAVI function in a room with disabled persons or infants only. 
Due to their limited motions, the ECONAVI sensor may judge no person is present, 
causing the indoor unit to stop the operation. 
						

							24(EN)
Blackout?
  After recovery from blackout, press 
[Start/Stop] again.
  àIf operation does not start, turn off the circuit 
breaker and consult the dealer of purchase 
about the symptom and Model No.
Is the circuit breaker 
turned off?   Turn it on and press [Start/Stop] again.   àIf operation does not start, turn off the circuit 
breaker and consult the dealer of purchase 
about the symptom and Model No.
Is  blinking? 
  After blinking stops, press [Start/Stop] 
again.
  àIf operation does not start, turn off the circuit 
breaker and consult the dealer of purchase 
about the symptom and Model No.
Is  displayed?
  If any of the following alarm indications 
appears, stop operation once and restart 
approx. 1 minute later.
(Alarm indication, off)
[•E04  •E06  •P10  •P20  •H06]
  àIf the indication does not reappear, use the unit.
  àIf the indication reappears or an alarm 
indication other than the above (combination of 
numbers and characters such as E, F, H, L and 
P) appears, stop operation, turn off the circuit 
breaker and consult the dealer of purchase 
about alarm indication, Model No. and indoor 
unit No.
Cannot stop the 
operation.
Or the unit starts to 
run automatically 
even if [Start/Stop] 
(Off) is pressed.
  Check if the outing function is activated or not. 
(
)
  Check control by central control device.
Troubleshooting
If operation does not start by pressing [Start/Stop] button ...
Check the following before asking for repair. 
						

							25(EN)
The remote 
controller screen 
displays a fl ashing 
“ 
 ”.
  Faulty sensor or incorrect installation. Turn OFF the ECONAVI function with the 
remote controller and contact the retailer or 
point of purchase with the Model No. and 
problem.
The remote 
controller screen 
does not display the 
 
.
  The indoor unit has stopped. Turn on the 
indoor unit.
  The unit is in Fan mode. The ECONAVI 
function does not operate in Fan mode.
  The ECONAVI function is set to OFF. Turn 
the ECONAVI function ON with the remote 
controller.
  The indoor unit may not support the 
ECONAVI function. If you turn the 
ECONAVI function ON with the remote 
control but there is no change, the indoor 
unit does not support the ECONAVI 
function.
Please contact the dealer.
•  If you need to contact for servicing, check the back cover of the operating instructions for indoor 
units or outdoor units. 
						

							26(EN)
Specifi cations
Model No. CZ-RTC4
Dimensions (H) 120 mm x (W) 120 mm x (D) 20 + 4.75 mm
Weight 160 g
Temperature/
Humidity range 0 ˚C to 40 ˚C / 20 % to 80 % (no condensation)
*Indoor use only.
Power Source DC16 V (supplied with indoor unit)
Clock Precision
± 30 seconds/month (at normal temperature 25 
˚C) 
*Adjust periodically.
Holding 
time 24 hours (when fully charged)
*Approx. 8 hours are required for full charge.
Number of 
connected indoor 
units Up to 8 units
© Panasonic Corporation 2015 
						

							Panasonic Corporation
1006 Kadoma, Kadoma City, Osaka, Japan
Operating Instructions
High-spec Wired Remote Controller
Model No. CZ-RTC3
Installation Instructions
Separately Attached.
ENGLISHBefore operating the unit, read these operating instructions thoroughly \
and keep them for future 
reference.
CV6233312187
WEB-URL Panasonic Corporation  
 Website:http://panasonic.net/ 
						

							2(EN)
Part Names Control panel
Note
LCD screen   Return button
Returns to the previous screen.Menu buttonDisplays the menu 
screen (P. 10).
Operation indicatorIlluminates during operation.
Blinks during alarm. 
Start/Stop buttonStarts/Stops operation.
Enter buttonFixes the selected content.
Press centre No glove No pen
Energy saving 
button
Switches Energy 
saving/Normal 
operation.
Cross key buttonsSelects an item.Up
DownRight Left 
						

							3(EN)
Safety Precautions
CAUTIONS
This appliance is intended to be used by expert or 
trained users in shops, in light industry and on farms, or 
for commercial use by lay persons.
This appliance can be used by children aged from 8 
years and above and persons with reduced physical, 
sensory or mental capabilities or lack of experience 
and knowledge if they have been given supervision or 
instruction concerning use of the appliance in a safe 
way and understand the hazards involved.
WARNING
Do not use this appliance in a potentially explosive 
atmosphere.
•  Do not operate with wet hands.
•  Do not wash with water.
In case of malfunction of this appliance, do not repair by 
yourself. Contact the sales or service dealer for repair.
In case of emergency, remove the power plug 
from the socket or switch off the circuit breaker 
or the means by which the system is isolated 
from the mains power.
 WARNINGCAUTION
This symbol refers to a hazard or unsafe 
practice which can result in severe personal 
injury or death. This symbol refers to a hazard or unsafe 
practice which can result in personal injury or 
product or property damage.
Matters to be observedProhibited matters 
						

							4(EN)
Note:
  This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this 
device must accept any interference received, including 
interference that may cause undesired operation.
  This equipment has been tested and found to comply with 
the limits for a Class B digital device, pursuant to Part 15 
of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more 
of the following measures:
•  Reorient or relocate the receiving antenna.
• 
Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different 
from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician 
for help.
  FCC Caution: To assure continued compliance, follow 
the attached installation instructions.  Any changes 
or modifi cations not expressly approved by the party 
responsible for compliance could void the user’s authority 
to operate this equipment.
Safety Precautions