Panasonic Cz Rtc4cz Rtc3 Operating Instructions Manual

Ã
Panasonic Corporation
1006 Kadoma, Kadoma City, Osaka, Japan
Operating Instructions
Timer Remote Controller
Model No. CZ-RTC4
Installation Instructions
Separately Attached.
ENGLISHBefore operating the unit, read these operating instructions thoroughly \
and keep them for future 
reference.
CV6233312187
 
Panasonic Corporation  
 http://www.panasonic.com 

2(EN)
Preparations How to Use Setting ChangeWhen 
NecessaryPage
Thank you for purchasing the 
Panasonic timer remote controller.
  Read the Operating Instructions 
carefully for safe use. This 
manual describes the Operating 
Instructions of the timer remote 
controller. Read this manual as 
well as operating instructions 
supplied with indoor units and 
outdoor units.
  Be sure to read the “Safety 
Precautions” (P.3, 4) before 
using.
  Keep this manual with operating 
instructions supplied with...

3(EN)
Safety Precautions
CAUTIONS
This appliance is intended to be used by expert or 
trained users in shops, in light industry and on farms, or 
for commercial use by lay persons.
This appliance can be used by children aged from 8 
years and above and persons with reduced physical, 
sensory or mental capabilities or lack of experience 
and knowledge if they have been given supervision or 
instruction concerning use of the appliance in a safe 
way and understand the hazards involved.
WARNING
Do not use...

4(EN)
Note:
  This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this 
device must accept any interference received, including 
interference that may cause undesired operation.
  This equipment has been tested and found to comply with 
the limits for a Class B digital device, pursuant to Part 15 
of the FCC Rules. These limits are designed to provide 
reasonable protection against...

5(EN)

Ã
Ã
13
6 5 4 3 1
2
12
11
10
987
Part Names 
1 Operation indicator
Illuminates during operation. Blinks during alarm.
2 Start/Stop button
Starts/Stops operation.
3 Fan speed
Changing the fan speed.
4 Swing/Air direction
Use this button to set the auto swing or air direction to a specifi c angle.
5 Unit select
When more than one indoor unit is operated by one remote control unit, this button is used to 
select a unit when adjusting the air direction.
6 Sleeping
7 Ventilation
Use this button when...

6(EN)
Ã
Ã
27 26
19 18 17 16 15 14 13 12 11 1028 1 2 3
4 25
23 24
20 22
215
6
7
8
9
1  Displayed if the selected feature was disabled during installation.
2  Displayed when a mistake is made during timer setting.
3  Appears when the timer program is being set.
4  Indicates today’s day of the week.
5  Displayed when the timer has been turned OFF.
6  Timer program indication
 
: The indoor unit starts operation at the programmed time.
 : The indoor unit stops operation at the programmed time.
7  Displays...

7(EN)
Basic Operations
How to Operate
Turn on the indoor unit before operation. See operating instructions of the indoor unit.
Start/Stop operation / Operation mode
1.  Press [Start/Stop] to start operation.

1
22.  Press the mode select button to select 
the mode among AUTO 
, HEAT , 
DRY 
, COOL  and FAN .* Auto: The mode is automatically switched to 
Cool or Heat to achieve the set temperature.
Set temperature
Press [/] to set the desired 
temperature.
Cannot be set in Fan mode.Temperature
Fan speed...

8(EN)
Note
  If the heating performance is insuffi cient in Low  fan speed, change the fan 
speed to Medium 
 or High .
  The temperature range that can be set varies depending on the model.
  Temperature sensor detects temperature in the vicinity of the air inlet of the 
indoor unit. The detected temperature slightly differs from the room temperature 
depending on the installation condition. The set temperature is a guideline of 
room temperature.  

9(EN)
1
Press and hold [SET] for more than 
2 seconds to enter the present day 
and time setting mode.
Once you enter the setting mode, 
“SETTING”, “▼”(day) and “time” fl ash.
2
Set “▼” to today’s day of the week.
Press [▲] to move “▼” (fl ashing on the 
display) in the order of: Su → Mo → Tu → ....
Press [▼] to move it in the order of: Su → 
Sa → Fr → ....
Press [SET] to store.
3
Press [▼/▲] to change the present 
“hour” in the range of 0 to 23*1.
Set the present hour and press [SET].
The “hour” digits...

10(EN)
Checking the Weekly Timer
•  Set the weekly program assigning a given timer to each day of the week. 
Maximum of 6 programs a day and 42 programs a week can be set.
Select the day and the TIMER number you want to program. 
1
Press [PROGRAM] to enter the 
program confi rmation mode
 “
” and start setting.
Once you enter the program confi rmation 
mode, the present day is indicated as 
TIMER No. “1”.
2 / 3 1
TIMER No. 1-62
program CHeck
2
Select the day.
Press [▼/▲] to move the “” horizontally on 
the...