Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Section 400-ProgrammingChapter 8. Least Cost Routing (FF8)
LCR Delete Tables
Software Version: All VersionsAddress: 
FF8 7# (TrunkGrp)# (DeleteDigits)#
DescriptionUse this address to assign Delete Digits to calls routed to an LCR trunk group.
Up to 16 digits can be assigned.
When an outgoing call is routed to an LCR trunk group, the DBS will check
the first digits of the dialed number and, if it finds a matching 
enny in this
table, the DBS will not 
outpulse the matched digits (only the rest of the...

Chapter 8. Least Cost Routing (FF8)Section 400-Programming
LCR Add Tables
Software Version: All VersionsAddress: FF8 
8## (TrunkGrp)# (AddDigits)#
DescriptionUse this address to assign Add Digits to calls routed to an LCR trunk group.
Up to 16 digits can be assigned.
When an outgoing call is routed to an LCR trunk group with Add Digits, the
DBS 
will add the digits to the beginning of the dialed number when it
outpulses the number to the CO.
This feature is often used to add CIC or PIC codes to dialed...

9. Copy Program Settings (FF9)
Use the FF9 program addresses in this chapter to copy settings among trunks,
extensions, and FF keys.
This chapter covers the following addresses:
FF9 AddressTopic
FF9 l# (Trunk)# (Trunk)#Trunk Copy
Page
9-3
FF9 2# (ExtPort)# (ExtPoft)##1 Extension Copy19-4
FF9 3# (ExtPon)# (ExtP0l-t)~1 FF Key Copy19-5
CBS-70-400DBS Manual - Issued 8/t/95Page 9-1 

.Page 9-2DBS Manual 
- Issued 8/l/95DBS-70-400 

Section 400-Programming
Chapter 9. Copy Program Settings (FF9)
Trunk Copy
Software Version: All VersionsAddress: 
FF9 l# (SourceTrunk)# (TargetTrunk)##
DescriptionUse this address to copy the attributes of one trunk to another.
Copying must be done on a trunk-by-trunk basis. The first trunk entry in this
address is the trunk being 
copiedfrom (the source); the second trunk entry is
the trunk being copied 
to (the m-get).
Programming
Note: You must enter two pound-signs (#I#) at the end of this address....

Chapter 9. Copy Program Settings (FF9)Section 400-Programming
Extension Copy
Software Version: All Versions
Address: FF9 2# (SourceExtPort)# (TargetExtPort)##
DescriptionUse this address to copy the attributes of one extension to another.
Copying must be done on an extension-by-extension basis. The first
extension port entry in this address is the extension being 
copiedfrom (the
source); the second extension entry is the extension being copied 
to (thetarget).
Programming
Note: You must enter two...

Section 400-ProgrammingChapter 9. Copy Program Settings (FF9)
FF Key Copy
Software Version: All VersionsAddress: 
FF9 3# (ExtPort)# (ExtPort)###
DescriptionUse this address to copy the attributes of one extension’s FF keys to another.
Copying must be done on an extension-by-extension basis. The first
extension port entry in this address is the FF key source; the second extension
entry is the FF key target.
Programming
Note: You must enter two pound-signs (#) at the end of this address.
FF9 3# (l-lf4)Y...

10. Speed Dial Programming (FFIO)
Use the FFlO addresses in this chapter to program speed dial numbers.
This chapter covers the following addresses:
F’FlO AddressTopic
Page
FFlO I# (SSD)# (DialedN0.WSystem Speed Dial Numbers10-3
FRO 2# (ExtPortM (PSDM (Dia1edNo.WPersonal Speed Dial Numbers10-5
DBS-70400DBS Manual- Issued 8/l/95Page 10-l 

Page 10-2DBS Manual - Issued 8/l/95DBS-70-400 

Section 400-ProgrammingChapter 10. Speed Dial Programming (FFlO)
System Speed Dial Numbers
Software Version: All VersionsAddress: 
FFlO 1# (SSD)# (PhoneNumber)#
DescriptionUse this address to set up System Speed Dial (SSD) codes and their related
phone numbers. An Attendant phone is required to program SSD numbers.
NOTE: Up to 90 SSD codes (00-89) can be assigned in CPC-A (all versions)
and CPC-AH/B versions prior to 7.0. Beginning with CPC-AWB Version
7.0, up to 200 SSD codes (000-199) can be assigned....