Panasonic Color Cctv Camera Wv Cw974 Operating Instructions

Auto tracking settings
LARGE :Zooms the target to a size that is
approximately three-fourths (vertically)
the size of the monitor screen. 
Notes:
• Sizes shown above are approximate and for
reference only. The actual size depends on
operating environment conditions and tracking
conditions.
• A larger target size setting will result in reduced
tracking performance.
(3) Configuring the Detection Sensitivity Setting
(SENSITIVITY)
1. Move the cursor to SENSITIVITY and then tilt the
joystick left or right to...

-42- CONTINUOUS :Zoom control is always performed.
This is the factory default setting.
(6) Configuring the Tracking Time Setting (AUTO
RELEASE)
Use this setting to specify a time after which auto
tracking should be forced to terminate after it starts.
The camera stops at the position it is in at the point the
tracking time is exceeded. If SELF RETURN is set, then
after the AUTO RELEASE time is up the SELF RETURN
time starts counting down and AUTO operation starts
again.
1. Move the cursor to AUTO...

-43- (10) Configuring the Target Frame Setting (INDICA-
TOR)
Use this setting to specify whether a target frame
should be displayed around the target during auto
tracking. The target frame can be used to specify the
target being tracked during pan, tilt, and zoom
operations.
1. Move the cursor to INDICATOR, and then tilt the
joystick left or right to select a target frame. 
OFF :Turns off display of the target
frame.
This is the factory default setting.
CANDIDATE :Displays a target assist frame dur-
ing...

-44-
Alarm settings
■Using the Alarm Setup Menu 
Display the alarm setup menu from the setup menu to
configure alarm settings. 
First, display the alarm setup menu. 
1. Display the setup menu (page 24), move the cursor
to ALARM O, and then press the CAM (SET) button. 
This will display the alarm setup menu. 
* The following sections numbered qto eexplain
how to use each of the alarm setup menu items. 
(1) Motion Detector Setting (MOTION DET)
1. Move the cursor to MOTION DET, and then tilt the
joystick...

6. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select an alarm detect dwell
time setting. 
After alarm detection, the next alarm is not detected
until the specified dwell time elapses. 
Tilting the joystick cycles through the setting
display in the sequence shown below. (unit: sec)
7. Move the cursor to RECOVER TIME, and then tilt
the joystick left or right to select an alarm reset time
setting. 
Tilting the joystick cycles through the setting
display in the sequence shown...

-46- 3. Move the cursor to ALARM IN 2, and then tilt the
joystick left and right to select the operation the
camera should perform when an external signal is
received by ALARM IN 2. 
OFF :Ignore alarm input signals. 
2POSI :Move to preset position 2.  
SEQ :Start sequential movement. 
PATROL2 :Start PATROL 2.
PATROL2 (S) :Start PATROL 2, and maintain the
stored picture quality settings
(page 37) even after completion. 
AUTOTRACK2 :Move to preset position number 2,
and then perform auto tracking. 
4. Move...

Special settings
■Using the Special Setup Menu 
Display the special setup menu from the setup menu to
adjust picture quality.  
First, display the special setup menu. 
1. Display the setup menu (page 24), move the cursor
to SPECIAL O, and then press the CAM (SET)
button. 
This will display the special setup menu. 
* This section explains items qthrough ton the
special setup menu in that order. 
(1) Adjusting Picture Quality 
Use the following procedure to adjust picture quality. 
1. Move the cursor to...

-48- (3) This returns to the PIX OFF menu.
An asterisk (*) to the right of a PIX OFF number
indicates that the number has a blemish
compensation pattern assigned to it. 
To delete a blemish compensation pattern
(1) On the PIX OFF menu screen, select of the
pattern you want to delete, and press the CAM
(SET) button. 
This will display the blemish compensation
pattern setting screen. 
(2) Press the F3 button. 
(3) This returns to the PIX OFF menu. 
This will delete the blemish compensation
pattern and...

-49-
Scene select setting
■Using the Scene Select Setting
Menu 
Display the scene select setting menu from the setup
menu to configure scene select settings. First, display
the scene select setting menu. 
1. Display the setup menu (page 24), move the cursor
to SCENE SELECT O, and then press the CAM
(SET) button. 
This will display the scene select setting menu. 
●Scene Select Settings
See page 25 for information on the scene select
settings method.
     **SCENE SELECT**
SCENE         INDOOR(L)
 LOAD
 RET...

Password settings
■Password Lock Settings 
Set the password lock on the setup menu. 
●Turning Password Lock On and Off 
The password lock function can be used to allow only
authorized personnel to change camera settings. A
password must be input in order to turn password lock
on or off. 
ON :Prohibits changing any settings except for
the password lock function.
Selecting this setting limits camera
configuration changes to authorized personnel. 
OFF :Settings on all menus can be changed.
If you are using...