Panasonic Color Cctv Camera Wv Cw974 Operating Instructions

Operation Examples
Important:Failure to configure settings in
accordance with the operating environment can
cause operational errors. Configure the settings
while carefully checking the AUTO TRACK setting
(page 41).
Note:If the alarm is turned on, an alarm signal is
continually output from ALARM OUT 1 while an auto
tracking operation is in progress.
4. Configure ALARM IN/OUT settings (page 45).
Select ALARM for CNT-CLS1.
5. Configure the SELF RETURN setting (page 35).
Select either 30S or SEQ.
Operation...

-22- 1. Configure the AUTO MODE setting (page 35).
Select AUTO PAN for the AUTO MODE setting and
then configure the AUTO PAN settings.
2. Configure PRESET (page 33) and ALARM IN/OUT
(page 45) settings.
Register the preset position where you want auto
tracking to start as preset position 1. To perform
auto tracking after ALARM IN 1, select
AUTOTRACK for the ALARM IN1 setting. 
Note:ALARM IN1 through 4 can be configured with
preset positions 1 through 4 to specify the auto
tracking start position in...

1. Configure the PRESET settings (page 33).
Register each preset position.
Select OFF for the AUTO TRACK setting of each of
the registered preset positions.
2. Configure the HOME POSITION (page 35) and
AUTO MODE (page 35) settings.
The HOME POSITION setting should be the position
from which you want to start auto tracking (such as
30POSI). For AUTO MODE, select SEQ.
3. Configure the AUTO TRACK setting (page 41).
Configure each parameter in accordance with the
operating environment.
Important:Failure to...

Using the setup menu
This manual describe procedures for operating system
controller WV-CU650. 
All setting configuration procedures start from the
setup menu. This section explains how to display the
setup menu and provides details about the menu items
that it contains. 
■Displaying the Setup Menu 
●When using the WV-CU650
(1) Select the camera (this camera), and the
monitor where displays the setup menu. 
(2) Press the MENU button to display LCD MENU
CAM 101. 
(3) Press the ENTER button or CAM (SET)...

-25-
■Scene Select Settings
Display the scene select setting menu from the setup
menu to configure scene select settings. First, display
the scene select setting menu. 
1. Display the setup menu (page 24), move the cursor
to SCENE SELECT O, and then press the CAM
(SET) button. 
This will display the scene select setting menu. 
●Scene Select Settings
Use the following procedure to configure scene select
settings. 
1. Move the cursor to SCENE, and then tilt the joystick
left or right to change the scene...

-26- 2. Move the cursor to →PUSH SET to the right of
PAN/TILT, and then press the CAM (SET) button to
display the PAN/TILT setting menu. 
3. Use the joystick to position the camera, and then
press the CAM (SET) button. 
4. Move the cursor to →PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET)
button to display the ZOOM/FOCUS setting menu. 
5. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM (SET) button.
Notes:
•
Focusing may be...

-27- 3. Use the joystick to move the cursor the character you
want to input, and then press the CAM (SET) button. 
The text input procedure is the same as that for
camera ID input. 
See steps 3 through 5 under “Camera ID Settings”
on page 24 for information about inputting the text
for the preset ID and specifying its position on the
display. 
To copy the preset ID of another position number 
Move the cursor to COPY, and then press the CAM
(SET) button. This displays the preset ID of the
position number...

Camera settings
■Using the Camera Setup Menu 
Display the camera setup menu from the setup
menu (Advanced Menu) to configure camera
settings (page 27). 
1. Display the setup menu (page 24), move the cursor to
CAMERA O, and then press the CAM (SET) button. 
This will display the camera setup menu. 
* The following sections numbered qto !3explain
how to use each of the camera setup menu items. 
(1) Camera ID (CAMERA ID)
See page 24 for information on the camera ID
settings method. The factory default...

-29- (2) Press the CAM (SET) button to mask the cell. 
Moving the cursor to a cell that is already
masked causes the blinking pattern of the
cursor to alternate between horizontal stripes
and white. 
Pressing the CAM (SET) button while the cursor
is located at a masked cell cancels the masking
of the cell. 
To cancel all masking areas, press the F3
button.
(3) After masking all of the cells you want, press the
MON (ESC) button to return to the ALC CONT
menu in step 1.
6. Move the cursor to LEVEL, and...

-30- (6) Synchronization (SYNC)
This camera supports the following three sync modes,
which are listed in priority sequence from highest
priority to lowest. 
(1) Multiplexed vertical drive (VD2) 
(2) Internal sync (INT)
(3) Line-lock (LL)
Input of a multiplexed vertical driver (VD2) signal
automatically switches to VD2 sync, regardless of the
cameras current sync mode (SYNC). In this case, the
camera setting menu shows EXT (VD2) for the SYNC
setting, which cannot be changed to internal sync
(INT) or...