Panasonic Color Cctv Camera Wv Cw974 Operating Instructions

-31- Note:White balance is adjusted in accordance with
on-screen color temperature, which the camera
detects automatically. Correct adjustment may not
be possible if a strong light source is shining on the
screen.
(8) Digital Noise Reduction (DNR) 
1. Move the cursor to DNR, and then tilt the joystick
left or right to select a digital noise reduction (DNR)
setting.  
LOW :Low DNR, Low afterimage. This is the factory
default setting.
HIGH :High DNR, High afterimage
(9) Resolution (RESOLUTION) 
1. Move the...

-32- (11) Auto Focus (AF MODE)
1. Move the cursor to AF MODE, and then tilt the
joystick left or right to select an auto-focus mode
setting.
MANUAL S.M.L :Activates auto-focus when the AF
button on the system controller is
pressed. 
AUTO S.M.L :Auto focus is used automatically
when PAN, TILT or ZOOM are
used in manual operation. 
The letters S (Small), M (Medium), and L (Large)
indicate the size of the auto-focus sensing area.  
The factory default setting is AUTO L.
Notes:
• The AUTO (S.M.L.) setting...

Pan/Tilt settings
■Using the Pan/Tilt Setup Menu 
Display the pan/tilt setup menu from the setup menu to
configure pan and tilt settings. 
First, display the pan/tilt setup menu. 
1. Display the setup menu (page 24), move the cursor to
PAN/TILT O, and then press the CAM (SET) button.
This will display the pan/tilt setup menu. 
* The following sections numbered qto !4explain
how to use each of the pan/tilt setup menu items. 
(1) Position Number Selection (PRESET)
Positions can be assigned numbers, each of...

●Auto Focus (AF MODE)
1. Move the cursor to AF MODE, and then tilt the joystick
left or right to select an auto-focus function setting.
MANUAL S.M.L :Auto focus does not operate
after moving to a preset position. 
AUTO S.M.L :Auto focus operates after
moving to a preset position. 
●Sequence/Sort DWELL Time 
(DWELL TIME)
This section explains how to set the length of time the
camera stops (time it stops rotating) and tapes the
scene while in the various preset positions for the
sequence and sort...

PTR 1 to 4 :Activates the patrol function when the
trigger time elapses. 
TRK :
After the trigger time elapses, the
camera returns to the home position and
then automatic tracking starts. Following
that, after a set time, the camera returns
to the home position and auto tracking
repeats. 
Notes:
• The HOME setting should be selected when you
want to normally leave the camera in the home
position and occasionally perform pan and tilt,
or when you want to activate SEQ. 
• PTR1-4 displays only the set...

5. Move the cursor to PAN LIMIT, and then tilt the
joystick left or right to toggle it on and off. 
ON :Limits manual panning to the zone between the
start point and the end point. The TILT range is
from horizontal to straight down. Select OFF for
the ENDLESS setting (step 3) when using this
setting. 
OFF :Allows manual panning outside the zone
between the start point and the end point. 
PAN LIMIT 
PAN LIMIT allows panning in the area from the start
point to the end point specified in step 1, but not in...

(2) Operate the camera to store the movements. 
LEARNING (***S) is displayed in the center of the
screen when the movements are being stored.
(unit: sec)
* (***S) indicates the amount of time that remains
for storing movements. 
(3) The setup menu is displayed and teaching stops. 
Storing movements stops when the remaining time
reaches 0S. 
Notes:
• Selecting LEARN to teach the camera a patrol
routine causes the following parameters to be
stored along with the camera movements. 
(1) Parameters at the...

6. Use the joystick to point the camera at the location to
be masked, and then press the CAM (SET) button. 
This registers the camera position and returns to
the zone setting menu. 
7. Move the cursor to →PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET) button.
This will display the ZOOM/FOCUS setting menu. 
8. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM (SET) button.  
This completes the adjustment procedure and
returns to...

(10) Digital Flip Setting (DIGITAL FLIP) 
Normally, a camera needs to stop when it points
straight down during tilt. With digital flip, however, the
camera is able to tilt from 0° to 180° in a single motion.
This makes it possible to track objects passing directly
under the camera more smoothly. The picture is
flipped vertically and horizontally when the camera is
at an angle of around 135°. 
1. Move the cursor to DIGITAL FLIP, and then tilt the
joystick left or right to toggle it on and off. 
ON :Turns...

4. Input an area title. 
The text input procedure is the same as that for
camera ID input. 
See steps 3 through 5 under “Camera ID Settings”
on page 24 for information about inputting the text
for the area title and specifying its position on the
display. 
5. Repeat steps 1 through 4 for the other area
numbers, if you want. 
(13) Tilt Angle Setting (TILT ANGLE) 
Selecting 5° for the TILT ANGLE setting allows tilting
past horizontal, in the range of -5° to 185°. 
1. Move the cursor to TILT ANGLE, and then...