Panasonic Color Cctv Camera Wv Cw864a Operating Instructions

							-31- 3. Open the SET UP menu to stop learning.
Notes:
•It is recommended to set PAN LIMIT to ON for
patrol-learn. Otherwise PAN LIMIT is invalid in
playback. 
•If the power fails in the patrol-learn mode, start
the patrol-learn function again from the starting
point.
•LEARN also stops 1 minute  after starting if the
memory is full.
•Auto refreshing may be activated in the patrol
play mode or the auto mode to calibrate the lens
position.
Patrol Play with a Controller Having the PATROL
Key
1. Press the PATROL PLAY key. The camera turns to
the starting point and reproduces the operations
stored in the memory. Iris operation is valid only in
the playback mode.
2. Press the PATROL STOP key and PROGRAM key
simultaneously to stop playback or press any manu-
al operation key (e.g., PAN/TILT/ ZOOM/FOCUS)
except the iris keys.
Patrol Play with a Controller not Having the PATROL
Key
1. Select patrol play in the setup menu, and then close
the menu. The camera turns to the starting point and
the operations stored in memory are reproduced.
Iris operation is valid only in the playback mode.
2. Open the SET UP menu, or press any of manual
operation keys (e.g., PAN/TILT/ ZOOM/FOCUS)
except the iris keys to stop playback.
Patrol Play with the AUTO PAN Key
1. If the PATROL PLAY function is assigned to the
AUTO PAN key, press the AUTO PAN key to turn the
camera back to the starting point and to reproduce
the operation data stored in the memory.
2. To stop playback, press the PATROL STOP key or
any manual operation key (e.g., PAN/ TILT/ ZOOM/
FOCUS) except the iris keys.
Notes: 
•In the patrol play mode, the camera movement may
occasionally deviate from the entered routine when
the routine includes a move to a preset position. If
this happens, re-enter the routine of manual opera-
tions for patrol-learn.
•In the patrol play mode, black and white automatic
switching does not work.
•In the patrol play mode, when the power of the con-
troller is turned on or off, the patrol play stops. In this
case, press the PATROL PLAY key again. (If SELF
RETURN is set to ON, the patrol play will start again
after elapsing the setting return time.)
●Alarm Input/Output (ALARM IN/OUT)
Move the cursor to ALARM IN/OUT, and press the CAM
(SET) key. The ALARM IN/OUT submenu appears.
Note:While the camera is in the AF mode or the lens
moves between WIDE and TELE, alarm input may
be ignored if several alarm inputs are received in
succession.
ALARM IN 1-4
Alarm input signals are supplied from external devices
through the ALARM IN connector to turn the camera to
a preset position.
1. Move the cursor to ALARM IN 1* and select a preset
position or OFF with the joystick, then press the
CAM (SET) key.
The factory default setting is OFF.
*Set ALARM IN 2, 3 and 4 in the same way as
ALARM IN 1.
1 POSI, 2 POSI, 3 POSI and 4 POSI:Preset posi-
tion. If an alarm input is received, the camera
turns to a preset position, and sends an alarm
output signal. The position number corresponds
to the alarm input number (1-1, 2-2, 3-3 and 4-4).
B/W:Available for ALARM INPUT 4 only. The cam-
era changes its mode from color to black and
white if ALARM IN 4 is supplied.
OFF:The camera ignores alarm inputs.
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     OFF
TILT ANGLE     0°
RET
   ** ALARM IN/OUT **
ALARM IN 1
ALARM IN 2
ALARM IN 3
ALARM IN 4
 
CNT-CLS 1
 TIME OUT
CNT-CLS 2
COAX ALM OUT
RET         OFF 
 OFF 
 OFF
 OFF
   
 OFF  
 100MS 
 OFF  
 OFF 
						

							-32-
CNT-CLS 1, 2 (Output)
Two contact closure signals (Open collector type) are
output through the Alarm Output connector.
1. Move the cursor to CNT-CLS 1, and select OFF,
ALARM or AUX 1 with the joystick.
The factory default setting is OFF.
When ALARM is selected, TIME OUT appears.
Select an appropriate duration from among 100 MS,
200 MS, 1000 MS (1 s), 2000 MS (2 s) and 4000 MS
(4 s) with the joystick.
The factory default setting is 100 MS.
Note:The shorter the duration, the more frequent
will be the detection output.
2. Move the cursor to CNT-CLS 2, then select OFF,
B/W or AUX 2 with the joystick.
The factory default setting is OFF.
OFF:Contact closure signals are deactivated.
ALARM:Available for CNT-CLS 1 only. A motion
detection signal is output.
AUX 1(2):An alarm signal is output when the cam-
era receives a command from the controller.
B/W:Available for CNT-CLS 2 only. ON (active) is
output when the camera operates in the black
and white mode if ALARM IN 4 is set to B/W.
Note:It is recommended to set the connected exter-
nal device to ignore the shorter alarm outputs of
90 ms or less from the camera.
COAXIAL ALARM OUT
Alarm output signals are supplied through the coaxial
cable.
1. Move the cursor to COAX ALM OUT and select ON
or OFF.
2. Press the CAM (SET) key.
The factory default setting is OFF.
ON:The camera sends an alarm output signal after
it turns to a preset position.
OFF:The camera does not send an output signal.
Notes:
•The camera ignores alarm inputs during manual
operation.
•Select OFF when the camera downloads or
uploads the preset data.
●Cleaning (CLEANING)
With CLEANING in the ON position, the camera’s built-
in electro-mechanical contacts are cleaned at regular
intervals (approx. every 7 days).
A dry contact adversely affects picture quality and
motors operation.
1. Move the cursor to CLEANING and select ON or
OFF with the joystick.
ON:The contacts are cleaned for approx. 1 minute.
CLEANING disappears when the cleaning
process is completed.
OFF:No contact cleaning.
Note:Select OFF when the camera downloads or
uploads the preset data.
●Electronic Zoom (EL-ZOOM)
The electronic zoom magnifies a scene 10-fold. With a
22-fold optical zoom lens, the camera is capable of
220-fold zoom.
1. Move the cursor to EL-ZOOM and select ON or OFF
with the joystick, and then press the CAM (SET) key.
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       ON
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     OFF
TILT ANGLE     0°
RET
CLEANING
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       ON
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     OFF
TILT ANGLE     0°
RET 
						

							-33-
ON:10 - fold electronic zoom is available with the
ZOOM switch on the controller.
OFF:The electronic zoom function is not used.
Notes:
•A scene magnified by the electronic zoom func-
tion may be inferior in picture quality to a non-
magnified one.
•The electronic zoom does not function in the pre-
set position setting mode.
•To set preset positions directly from WV-CU360
System Controller, you need to set the electronic
zoom function temporarily to OFF.
●Preset Alarm (PRESET ALM)
An alarm output is sent when the camera moves to the
designated position depending on the mode.
1. Move the cursor to PRESET ALARM and select ON
or OFF.
ON:Alarm signals are output in the following cases.
•When a preset positioning sequence is complet-
ed while AUTO MODE is set to SEQ.
•When a preset positioning sequence is complet-
ed while AUTO MODE is set to SORT.
•When the self-return function has returned the
camera to its home position.
•Positioning is completed for a position request
command.
•Positioning to the designated point is completed
for ALARM IN/OUT.
•When positioning to the starting point is complet-
ed while AUTO MODE is set to AUTO PAN.
•When positioning to the starting point is complet-
ed while PATROL is set to PLAY.
OFF:Alarm signals are not output.
Note:Select OFF when the camera downloads or
uploads the preset data.
●Image Hold (IMAGE HOLD)
The camera picture remains as a still image on the
monitor screen until the camera reaches the preset
position. This function is useful for surveillance via local
area network.
1. Move the cursor to IMAGE HOLD and select ON or
OFF.
ON:The last displayed still image is shown till the
camera finishes moving to a preset position.
However, the still image may be distorted with
the effect of panning or tilting.
OFF:The current image is being displayed while the
camera is moving to a preset position.
●Tilt Angle (TILT ANGLE 0 °/5 °)
You can select the tilting range.
1. Move the cursor to TILT ANGLE and select 0 ° or 5 °.
0°:The tilting range is between 0 ° and 180 °.
5°:The tilting range is between –5 ° and 185 °.
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     ON
IMAGE HOLD     OFF
TILT ANGLE     0°
RET
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     ON
TILT ANGLE     0°
RET
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     ON
TILT ANGLE     0°
RET 
						

							-34-
■Camera Setting
●To Display the Camera Setting Menu
Move the cursor to CAMERA O, and press the CAM
(SET) key. The camera setting menu appears.
●Camera Identification (CAMERA ID)
1. Move the cursor to CAMERA ID, and select ON to
display the camera identification with the joystick.
2. Follow the steps below to edit the camera ID char-
acters.
2-1 Move the cursor to CAMERA ID and press the
CAM (SET) key to display the character editing
menu.
2-2 Move the cursor to the character you want to edit
or change with the joystick, and press the CAM
(SET) key. The selected character appears in the
editing area.
2-3 Repeat the steps above until all characters are
edited.
3. After editing the camera identification characters,
follow the steps below to decide the position of
CAMERA ID.
3-1 Move the cursor to POSI, and press the CAM
(SET) key to display the ID position menu.3-2 Decide the position of the camera ID with the joy-
stick. Press the MON (ESC) key to fix the posi-
tion, and return to the character editing menu.
Notes:
•When you want the pointer to move to a specific
character in the editing area, select a new char-
acter, and press the CAM (SET) key. This func-
tion allows you to edit or correct a specific char-
acter.
•To enter a blank space into the camera ID, move
the cursor to SPACE, and press the CAM (SET)
key.
•To erase all characters in the editing area, move
the cursor to RESET, and press the CAM (SET)
key.
•The positioning of CAMERA ID stops at the
edges of the screen.
•CAMERA ID moves faster when the joystick is
kept at the right or left for one second or more.
•Move the cursor to RET to return to the SET UP
menu, and press the CAM (SET) key.
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK OFFOFF
OFF
OFF
AUTO PAN
ON
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2    OFF 
 ALC 
 AUTO
 ON(MID)
 OFF
 INT  
 ATW1 
 OFF  
 AUTO L
 
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   ON 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1 
OFF 
AUTO L
 
     CAMERA ID
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
         POSI RET RESET
    CAM1............
    
CAM1
     CAMERA ID
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
         POSI RET RESET
    CAM1............
    
     CAMERA ID
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
         POSI RET RESET
    CAM1............
     
						

							-35-
●Light Control Setting (ALC/MANUAL)
1. Move the cursor to ALC/MANUAL and select ALC or
MANUAL with the joystick. When you select ALC,
set backlight compensation.
Note:The backlight compensation submenu associ-
ated with this menu is described separately and
should be set up after installing the camera at
the site and observing the actual site picture.
2. When MANUAL is selected, quit the setup menu by
pressing the MON (ESC) key. Press the OPEN or
CLOSE key on the controller for iris adjustment.
(1) ALC Mode with SUPER-D2 ON
1. Press the CAM (SET) key after selecting ALC. The
ALC CONT menu appears.
2. Move the cursor to the SUPER-D2 parameter and
select ON.
3. If you want to adjust the video output level, move the
I cursor for LEVEL. Adjust it to the desired level
with the joystick.
4. Move the cursor to RET and press the CAM (SET)
key to return to the CAM SET UP menu. To return to
the camera picture, press the F4 button.
(2) ALC Mode with SUPER-D2 OFF
1. Move the cursor to SUPER-D2 and select OFF.
(When you select MANUAL, SUPER-D2 is not avail-
able.) MASK SET appears on the menu.
2. Move the cursor to MASK SET and press the CAM
(SET) key. The 48 mask areas appear on the monitor
screen. The cursor is blinking in the top left corner of
the screen.
3. To mask an area where backlight is bright, move the
cursor to the area and press the CAM (SET) key.
The mask turns white. Repeat this procedure to
mask the desired areas.
4. To cancel a masked area, move the cursor to the
area, and press the CAM (SET) key. To cancel all
masking areas, press the F2 button of WV-CU550C.
For WV-RM70, press the right and left switches
simultaneously.
5. After masking is completed, press the MON (ESC)
key. The 48 mask areas on the monitor screen dis-
appear and the ALC CONT menu appears.
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1 
OFF
AUTO L
  
    ** ALC CONT **
    BACK LIGHT COMP
SUPER-D2
MASK SET 
LEVEL
RETOFF
••|••••••
-       +
    ** ALC CONT **
    BACK LIGHT COMP
SUPER-D2
 
LEVEL
RETON
••|••••••
-       +
Blinking
Blinking
Blinking
Turns to white 
						

							-36- 6. If you want to change the picture contrast, move the
I cursor for LEVEL and adjust the level.
7. Move the cursor to RET and press the CAM (SET)
key to return to the CAM SET UP menu.
To return to the camera picture, press the F4 button.
●Shutter Speed Setting (SHUTTER)
Note:When ON is selected for SUPER-D2 on the ALC
CONT menu, only OFF and AUTO are available.
To select an electronic fixed shutter speed, select
OFF for SUPER-D2 in the menu.
Move the cursor to SHUTTER and select the elec-
tronic shutter speed with the joystick. The electronic
shutter speed changes as follows with the joystick:
•When OFF is selected for SUPER-D2 on the ALC
CONT menu•In the AUTO mode, an object is clearly imaged
under highlighted conditions by using the combina-
tion technology of iris and shutter functions.
Note:When the selected shutter speed caused
flicker on condition that fluorescent lamps stay
on, change this setting to OFF.
●Gain Control [AGC ON (LOW/ MID/
HIGH)/OFF]
Move the cursor to AGC and select ON (LOW), ON
(MID), ON (HIGH) or (OFF) with the joystick.
Notes:
•Even if AGC is set to ON and if the noise reduction
function is enabled, afterimages may be produced
by shooting a moving object or by panning or tilting
the camera.
•For more information, refer to Digital Noise
Reduction on page 41.
●Electronic Sensitivity Enhancement
(SENS UP)
Move the cursor to SENS UP and select the desired
electronic sensitivity enhancement mode with the joy-
stick. The electronic sensitivity enhancement mode
changes as follows with the joystick:
•When OFF is selected for SUPER-D2 on the ALC
CONT menu
    ** ALC CONT **
    BACK LIGHT COMP
SUPER-D2
MASK SET 
LEVEL
RETOFF
••••|••••
-       +
    ** ALC CONT **
    BACK LIGHT COMP
SUPER-D2
MASK SET 
LEVEL
RETOFF
••••|••••
-       +
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1 
OFF
AUTO L
  
OFF (1/60)1/100 AUTO
1/10 0001/4 000 1/2 000 1/1 0001/2501/500
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1
OFF
AUTO L
  
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1
OFF
AUTO L
  
X2 AUTOOFFX4 AUTOX6 AUTOX10 AUTO
X16 AUTO
X32 AUTOX2 FIX
X6 FIXX10 FIXX16 FIX X32 FIX
X4 FIXOFF 
						

							-37- •When ON is selected for SUPER-D2 on the ALC
CONT menu
Notes:
•When ON is selected for SUPER-D2 in the ALC
CONT menu, FIX is not available for this item.
•When AUTO is selected for SENS UP and ON is
selected for SUPER-D2, the SENS UP function has
priority so that the SUPER-D2 function is not activat-
ed automatically.
•While the SENS UP function is selected, noise or
spots may appear in the picture when the sensitivity
of the camera is increased. This is a normal phe-
nomenon.
●Synchronization (SYNC)
Move the cursor to SYNC and select LL or INT with the
joystick.
Important Notices:
1. The priorities of SYNC modes are assigned as fol-
lows:
1. Multiplexed vertical drive (VD2) (highest priority)
2. Line-lock (LL)
3. Internal sync (INT) (lowest priority)
2. To use internal sync, select INT.
3. Whenever the vertical drive pulse (VD2) is supplied
to the camera, the camera sync mode is automati-
cally switched to the multiplexed vertical drive pulse
(VD2) regardless of the selected sync mode.
Line-lock Sync Mode (LL)
1. Move the cursor to SYNC and select LL with the joy-
stick. The LL sync mode is not available when the
multiplexed vertical drive (VD2) pulse is supplied.
2. After selecting LL, press the CAM (SET) key.
The SYNC menu appears on the monitor screen.3. Supply the video output signal of the camera to be
adjusted and the reference video output signal to a
dual-trace oscilloscope.
4. Set the dual-trace oscilloscope to the vertical rate
and expand the vertical sync portion on the oscillo-
scope.
5. Move the cursor to COARSE with the joystick.
6. Match the vertical phases for both video output sig-
nals as closely as possible with the joystick. The
coarse adjustment can be performed in steps of
22.5 degrees (16 steps) with the joystick.
Note:After the 16th step, the adjustment level
returns to the first step.
7. Move the cursor to FINE by using the joystick.
X2 AUTO OFFX4 AUTOX6 AUTOX10 AUTO
X32 AUTO X16 AUTO
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1
OFF
AUTO L
  
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF
ALC 
AUTO
ON(MID)
OFF
LL  
ATW1
OFF
AUTO L
  
      ** SYNC **
V PHASE
COARSE
FINE
RET1(1--16)
••|••••••
-       +
1 (1 - - - 16): 0 degrees
2 (1 - - - 16): 22.5 degrees
16 (1 - - - 16): 337.5 degrees
      ** SYNC **
V PHASE
COARSE
FINE
RET1(1--16)
••|••••••
-       + 
						

							-38- 8. Match the vertical phase for both video output sig-
nals as closely as possible with the joystick.
Notes:
•When the | cursor reaches the + end, it jumps
back to –. At the same time, COARSE is incre-
mented by one step to enable a continuous
adjustment. The reverse takes place when the |
cursor reaches the – end.
•When the joystick is kept at the right or left for
one second or more, the | cursor moves quick-
ly.
•To reset COARSE and FINE to the preset values,
press the F2 button of WV-CU550C. For WV-
RM70, press the right and left switches simulta-
neously. COARSE is preset to zero-crossing of
the AC line phase.
•If the AC line phase contains spike noise, etc.,
the vertical phase of the video output signal may
be disturbed.
●White Balance (WHITE BAL)
(1) Auto-Tracing White Balance Mode (ATW1/ ATW2)
1. Move the cursor to WHITE BAL and select ATW1
with the joystick. The white balance of the camera is
automatically adjusted.2. For fine adjustment of ATW1/ATW2, press the CAM
(SET) key. The ATW1/ATW2 fine adjustment menu
appears on the monitor screen.
3. Move the cursor to RET with the joystick and press
the CAM (SET) key to return to the SET UP menu.
(2) Automatic White Balance Control Mode (AWC)
1. Move the cursor to WHITE BAL and select AWC →
PUSH SW with the joystick.
2. Press the CAM (SET) key to start the white balance
setup. PUSH SW is highlighted to indicate that white
balance is being set.
3. PUSH SW returns to normal when balance setting is
completed.
4. For fine adjustment of the AWC, move the cursor to
AWC and press the CAM (SET) key. The AWC fine
adjustment menu appears on the monitor screen.
5. Move the cursor to RET with the joystick and press
the CAM (SET) key to return to the SET UP menu.
      ** SYNC **
V PHASE
COARSE
FINE
RET4(1--16)
••••••|••
-       +
      ** SYNC **
V PHASE
COARSE
FINE
RET1(1--16)
•|•••••••
-       +
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1
OFF
AUTO L
 
      ** ATW1 **
R
B
RET••••|••••
-       +
••••|••••
-       +
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
AWC
→PUSH SWOFF  
AUTO L
 
      **  AWC  **
R
B
RET••••|••••
-       +
••••|••••
-       + 
						

							-39-
●Motion Detector (MOTION DET)
1. Move the cursor to MOTION DET and select ON or
OFF with the joystick.
2. If ON is selected, press the CAM (SET) key. The
MOTION DETECT menu appears.
You can mask the areas in this menu.
3. Move the cursor to MASK SET and press the CAM
(SET) key. 48 mask areas appear on the monitor
screen.
Refer to Light Control Setting on page 35 for mask-
ing operations.
4. After masking areas, press the MON (ESC) key. The
MOTION DETECT menu appears on the monitor
screen.
5. Move the cursor to ALARM and select ON or OFF
with the joystick.
ON:The alarm signal is supplied while the display
mode is activated.
OFF:The alarm signal is not supplied while the dis-
play mode is activated.
6. Move the cursor to DISPLAY MODE.
Press the CAM (SET) key to see the present setting.
The areas that detect the motions blink.
7. Move the cursor to LEVEL with the joystick.
Obtain the optimum detection level with the joystick.
Note:Repeat the above procedure until you obtain
the adjusted results.8. Dwell Time
Move the cursor to DWELL TIME, and select a time
with the Joystick.
When the time specified here elapses after motion
detection, the camera will notify the connected
device of the alarm activation. The default setting is
2 seconds.
Selectable times (seconds): 2s, 5s, 10s, 30s
9. Move the cursor to RECOVER TIME with the joystick.
You can select the following recover times.
10. Move the cursor to RET and press the CAM (SET)
key to return to SET UP.
Important Notices:
•The motion detection should meet the following con-
ditions.
1) The picture size on the screen should be larger
than 1/48 of the actual picture size.
2) The contrast ratio between the object and the
background picture should be more than 5 % at
the maximum detection level.
3) The time that takes the object to move from one
end of the screen to the other should be more
than 0.1 second.
•Also under the following conditions, mask or adjust
the detection level to prevent malfunction.
1) When leaves, curtains, etc. are swayed by the
wind.
2) When a picture has a high noise content due to
low light conditions.
3) When the object is illuminated by lighting equip-
ment that constantly turns on and off.
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1
ON  
AUTO L
  
   ** MOTION DETECT **
LEVEL
DWELL TIME      2S
DISPLAY MODE
       ALARM    OFF
MASK SET 
RECOVER TIME
RET•••|•••••
-       +
  
  1MIN
2MIN 3MIN 5MIN 10MIN
60MIN
30MIN 20MIN1MIN
OFF 
						

							•The alarm signal will take approx. 0.2 seconds to
reach the alarm terminal of the VCR after the camera
detects the object.
Because the alarm signal is multiplexed on the
video signal, it may be mistakenly interpreted by
other video equipment as a time code signal.
Therefore, when this camera is not used in a
Panasonic Intelligent CCTV System, select OFF to
prevent the above from occurring.
●Auto Focus Setting (AF MODE)
1. Move the cursor to AF MODE, and select the follow-
ing mode with the joystick. S, M and L stand for
Small, Middle and Large areas respectively in the
center of a scene that are used for sensing sharp-
ness in auto-focusing.
MANUAL S, M, L:Auto focus is activated only when
the AF key on the controller is pressed.
AUTO S, M, L:Auto focus is activated automatically
while the pan, tilt or zoom operation is manually
performed. These may be selected in the same
way as MANUAL by pressing the AF key on the
controller.
2. To confirm auto-focus operation, press CAM (SET)
key.
Notes:
•When the electronic sensitivity enhancement (SENS
UP) is activated except in the x2 FIX or x2 AUTO
mode, this function is automatically set to MANUAL
(S, M, L).
•The auto focus lens does not function properly in the
AUTO mode after using the WIDE lens.
•The auto focus lens may not function properly in the
AUTO mode under the following conditions.
1. Dirt or water on window glass.
The auto focus may focus on the dirt or water.
2. Low lighting or illumination.
3. Bright objects or high intensity objects.
4. Single color object such as a white wall or fine
felt
5. No center objects and sloping objects
6. Far and near objects on the screen
●Special 2 Menu (SPECIAL2)
This menu lets you adjust and set up the picture quality
to meet your requirements.
Move the cursor to SPECIAL2 and press the F2 button
of WV-CU550C. The special menu appears on the mon-
itor screen. For WV-RM70, hold down the right and left
switches simultaneously for 2 seconds or more.
•Chroma Level (CHROMA GAIN)
Aperture Level (AP GAIN)
Pedestal Level (PEDESTAL)
Hue Level Setting (HUE)
1. Move the cursor to CHROMA GAIN, and the I cur-
sor is highlighted.
2. Move the I cursor to your desired position with the
joystick and press the CAM (SET) key to confirm the
level.
Notes: 
•For setting the aperture, pedestal and hue levels,
perform the same steps described above (but in
the step 1, move the cursor to AP GAIN for the
aperture level, to PEDESTAL for the pedestal
level and to HUE for the hue level.).
•To reset the settings to the factory default, press
the F2 button of WV-CU550C/CJ. (For WV-RM70,
hold down the right and left switches simultane-
ously for 2 seconds or more.)
• Resolution (RESOLUTION)
Move the cursor to RESOLUTION and move the joystick
to select NORMAL or HIGH.
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1
OFF
AUTO L
AUTO SAUTO M AUTO L
MANUAL L MANUAL M MANUAL S
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET     SPECIAL2   OFF 
ALC 
AUTO
ON(MID)
OFF
INT  
ATW1
OFF
AUTO L
     ** SPECIAL2 **
CHROMA GAIN  –         +
AP GAIN      –         +
PEDESTAL     –         +
HUE          –••••
|••••+
RESOLUTION  
DNR            LOW2
BW MODE
PIX OFF
REFRESH
CAMERA RESET
RET
••••|••••
••••|••••
••|••••••
 NORMAL
 
  
   
→PUSH SET→PUSH SET
••••|••••
••••|••••
••|••••••
 NORMAL
 
  
   
→PUSH SET→PUSH SET      ** SPECIAL2 **
CHROMA GAIN  –         +
AP GAIN      –         +
PEDESTAL     –         +
HUE          –••••
|••••+
RESOLUTION  
DNR            LOW2
BW MODE
PIX OFF
REFRESH
CAMERA RESET
RET
-40-