Panasonic Color CCTV Camera Wv Cl930 WV CL934 Series Operating Instructions

41
ON:Displays black-and-white images. 
OFF (default):Displays color images. 
Note: 
If a subject is always moving or the
screen is occupied with a uniform color,
brightness determination may be not per-
formed successfully because the bright-
ness is merely determined by information
from the CCD image sensor. When
AUTO2 is selected, the wave length of
the light source shall be 800 nm or
longer. 
Step 3
Move the cursor to LEVEL and select a
brightness level at which switching between
color and...

42
    **CAMERA SETUP** 2/2
PRIVACY ZONE OFF    
MIRROR       OFF
LENS-DRIVE   DC
STABILIZER   OFF
RET TOP END  **ZONE NUMBER 1 /8** 
   
    
 
 RET TOP END  **ZONE NUMBER 1 /8** 
POSITION      PUSH SW
SCALE         PUSH SW
 SET DEL
 RET TOP END
12. Privacy zone setting [PRIVACY ZONE]
When undesired portions in the camera shooting area (on the screen) exist, those portions (pri-
vacy zone) are hidden. 
ON (1):Grays the zone.
ON (2):Mosaics the zone. 
OFF (default):Displays the zone normally. 
Up to 8...

43
Step 4
Move the cursor to POSITION and press the setting button. 
Step 5
Use the up, down, right, and left buttons to decide the zone position and press the setting but-
ton. 
→The zone position is determined. 
Step 6
Move the cursor to SCALE and use the up, down, right and left buttons to adjust the zone
frame size. The up and down buttons decide the vertical size, and the right and left buttons
decide the horizontal size. Press the setting button after the zone frame size setting.  
Step 7
Move the...

44
15. Image stabilizer setting [STABILIZER]
ON or OFF is selected to decide whether or not to enable the image stabilizer. 
This function is effective for the case that the camera is installed on a power pole or other
poles. 
ON:Enables the image stabilizer. 
OFF (default):Disables the image stabilizer.  
Important:
• When ON is selected for the image stabilizer, the view angle becomes narrower and the
resolution becomes lower. When ON is selected for the image stabilizer, check the view
angle and...

45
  **BACK-FOCUS SETUP**  
ABF           PUSH SW
MANUAL-ADJ
C/L   B/W     AUTO
SETUP-SW LOCK OFF   
 NEAR     FAR
  .........
|.........
INDICATOR XXXX
 RET TOP END
BACK-FOCUS SETUP screen The back focus setting type is selected and fine adjustment is performed. The following setting
is performed on the BACK-FOCUS SETUP screen through the top screen. Refer to pages 21 -
22 for how to call up the screen. The lens adjustment (pages 16 - 17) shall be performed
before the back focus adjustment. 

The back...

46
AUTO (default):Adjusts the back focus function automatically and corrects out of focus when
switching between color and black-and-white images. 
PRESET:Performs the preset movement to each specified back focus position when switching
between color and black-and-white images. The preset position is the back focus position
specified last time, which was automatically memorized for each of color images and
black-and-white images.
FIX:Fixes the position after adjusting the back focus either automatically...

47
Special Menu Setup [SPECIAL SETUP]
The special menu setup is performed including the setting of the camera image quality and the
communication configuration when a receiver is used. The following settings are performed on
the SPECIAL SETUP screen through the top screen. Refer to pages 16 - 17 for how to call up
the screen. 
Chroma level adjustment [CHROMA GAIN]
Use the right or left button to adjust the color density of the camera image. When the level indi-
cator moves in the + direction, the color...

48
Chroma phase level (hue) adjustment [HUE]
Use the right or left button to adjust the hue of the camera image. Be sure to view a vector
chromaticity indicator or a color video monitor when the adjustment is performed.
Note: 
Holding down the right and left buttons for more than 2 seconds simultaneously restores
the settings of “CHROMA GAIN”, “AP GAIN”, “PEDESTAL”, and “HUE” to the default set-
tings.
Pixel compensation [PIX OFF] 
Flaws in the displayed camera image are corrected, which is called pixel...

49
Notes: 
• To clear the registered pixel compensation point, move the cursor to the number with which
the target pixel compensation point is registered on the PIX OFF screen and press the
setting button. The pixel compensation positioning screen appears, and then hold down
the right and left buttons for more than 2 seconds simultaneously. The PIX OFF screen
appears, the pixel compensation point is cleared, and 
* at the right side of the number
disappears. 
• When an auto iris lens with video signal...

50
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END
Language Selection [LANGUAGE SETUP]
A language for the setup menu is selected from the following: The language selection is per-
formed on the LANGUAGE SETUP screen through the top screen.
JAPANESE/ENGLISH (Default)/FRANÇAIS/ESPAÑOL/DEUTSCH/ITALIANO/
êìëëäàâ
To change the language to be used, use the right or left button to select the target language,
move the cursor to SET, and press the setting button. 
Notes: 
• When the language is...