Panasonic Color CCTV Camera Wv Cl930 WV CL934 Series Operating Instructions

31
6. Synchronization setting [SYNC]
This unit supports the following 5 types of synchronization methods, and one of the following is
selected. 
The order of descriptions below indicates the order of priorities. 
qMultiplexed vertical drive signal (VD2) 
wPower supply synchronization (LL)  
* Synchronization is performed on the basis of the power supply frequency. 
eComposite color video signal or black burst signal (VBS) 
rMonochrome composite video signal or composite synchronizing signal (VS)...

32
Adjustment of phase in power supply synchronization mode (LL)
The adjusting video signal of the camera and the criterial external synchronizing input signal
are connected to a 2-input oscilloscope and the phase is adjusted. 
Note:
Movement of the camera or presence of a spike noise in the power line may cause vertical
phase change. In such a case, adjust the phase again. 
Follow the procedure in the next page to adjust the phase. 
        **SYNC**        
   
V PHASE    
COARSE         1(1--16)
FINE...

33
Step 1
Provide a VBS signal to the external synchro-
nizing input connector on the rear side of the
camera. 
→The SYNC setting automatically
changes to EXT (VBS). 
Step 2
Move the cursor to EXT (VBS) and press the
setting button. 
→The SYNC screen appears. 
Step 3
Connect the video output signal and external
synchronizing input signal of the camera to a
2-input oscilloscope, and move the cursor to
H PHASE. 
Step 4
Adjust the oscilloscope to the horizontal rate,
and extend the horizontal synchronizing...

34
Adjustment of phase in VS genlock mode (VS) 
The adjusting video signal of the camera and the criterial external synchronizing input signal
are connected to a 2-input oscilloscope and the phase is adjusted. Follow the procedure below
to adjust the phase. 
        **SYNC**        
   
H PHASE       ...
|...128
              -     +
 RET TOP END
    **CAMERA SETUP** 1/2
CAMERA ID    OFF    
ALC/ELC      ALC    
SHUTTER      OFF
AGC          ON
SENS UP      OFF
SYNC         INT
WHITE BAL    ATW1
MOTION...

35
7. White balance setting [WHITE BAL]
The white balance adjustment is selectable from the following.
ATW1 (default):Activates the automatic color temperature tracking mode.  The camera contin-
uously measures the color temperature of the light source and automatically adjusts the
white balance. Manual fine adjustment is also enabled after automatic white balance set-
ting. (page 36)
The adjustment of the color temperature ranges from approx. 2 700 K to 6 000 K.  If the sit-
uation meets one of the...

36
8. Motion detector function setting [MOTION DET] 
The motion detector function is set. Either MODE1 or MODE2 is selected. When MODE1 is
selected, the detailed settings such as settings of the detection sensitivity and detection area
are required. The detection area can be specified and checked in the demonstration mode. 
MODE1:Provides an alarm signal when a motion is detected. 
MODE2:Provides an alarm signal when the camera is covered or the camera direction is
changed. 
OFF (default):Disables the...

37
Detection condition
Subject size:A moving subject needs to be equal to or larger than 1/48 of the screen at STA-
BILIZER OFF. 
Subject contrast:The contrast ratio between the background and moving subject needs to be
equal to or larger than 5 % (at maximum sensitivity). 
Subject moving speed:The passing time for a subject to move from the end to the other end
of the screen needs to be equal to or larger than 0.8 seconds (at 5 % of contrast ratio). A
subject moving faster than the description above is...

38
        **MODE1**     
   
LEVEL         ...
|...128
              -     +
DWELL TIME    2S
DISPLAY MODE
     ALARM    OFF
MASK SET
 RET TOP END
    **CAMERA SETUP** 1/2
CAMERA ID    OFF    
ALC/ELC      ALC    
SHUTTER      OFF
AGC          ON
SENS UP      OFF
SYNC         INT
WHITE BAL    ATW1
MOTION DET   OFF
DNR          HIGH
RESOLUTION   HIGH    
BW MODE
Advanced settings about motion detector function (MODE1) 
The description below specifies the sensitivity level and detection area of the motion...

39
Step 6
Move the cursor to DISPLAY MODE and press the setting button. 
→The demonstration mode is implemented, and the blocks on which significant brightness
change was detected blink. 
Step 7
Press the setting button. 
→The demonstration mode is terminated, and MODE1 screen appears again. 
Step 8
Move the cursor to LEVEL and use the right or left button to adjust the detection sensitivity
level. When the level indicator moves in the + direction, the level becomes higher. When the
level indicator moves...

40
9. Digital noise reduction function setting [DNR]
The digital noise reduction function reduces noise automatically under the condition of low illu-
minance. The effect level of the noise reduction function is selectable from the following: 
LOW:Low level of noise reduction (small residual image)
MID:Medium level of noise reduction (medium residual image)
HIGH (default):High level of noise reduction (large residual image)
10. Image resolution setting [RESOLUTION]
A resolution of camera images is...