Panasonic Aj Yad250 Operating Instructions Manual

							E– 20
ENGLISH
: S-VIDEO signals will not be output to DVCPRO I/F when set-up menu
item No. 807 DIF NSTD IN is set to OFF.
DVCPRO I/F modeVIDEO OUT
MONITOR OUTAUDIO OUT
HEADPHONE
Output EE (LINE/S-VIDEO)Output stop
Output TAPE
Input
Input stop
Output TAPE
Output TAPE
Output TAPE
Output TAPE
Output EE (LINE/S-VIDEO)Output stop
Output stop
Input
Input stop
Output TAPE
Output EE (LINE/S-VIDEO)Output stop
Input
Input stop
Output EE (LINE/S-VIDEO)Output stop
Input
Input stopEE (LINE/S-VIDEO)
Black
TAPE
EE (DVCPRO I/F)
Black
EE (LINE/S-VIDEO)
Black
TAPE
TAPE
EE (LINE/S-VIDEO)
Black
Black
EE (DVCPRO I/F)
Black
TAPE
EE (LINE/S-VIDEO)
Black
EE (DVCPRO I/F)
Black
EE (LINE/S-VIDEO)
Black
EE (DVCPRO I/F)
BlackEE (AUDIO IN)
No output
No output
EE (DVCPRO I/F)
No output
EE (AUDIO IN)
No output
TAPE (CUE)
TAPE (CUE)
EE (AUDIO IN)
No output
No output
EE (DVCPRO I/F)
No output
TAPE
EE (AUDIO IN)
No output
EE (DVCPRO I/F)
No output
EE (AUDIO IN)
No output
EE (DVCPRO I/F)
No output 
						

							E– 21
AJ-D250 VTR modes and input/output statuses
Once this board is installed in the AJ-D250, the displays or operation of
functions for some of the AJ-D250 menu settings or modes may differ from
the time before the board is installed.
VTR modeINPUT SELECT
switch (front
panel) positionS/F/R EE SEL
(set-up menu item
No.102)Input signal
status
Normal signal
No signal
Normal signal
No signal
V InsertLINE/S-VIDEO N/A
A InsertLINE/S-VIDEO N/A
Normal signal
No signal
AV InsertLINE/S-VIDEO N/A
The audio insert mode is not acknowledged when the switch
is at the OPTION position.
The video insert mode is not acknowledged when the switch
is at the OPTION position.
The audio/video insert mode is not acknowledged when the
switch is at the OPTION position. 
						

							E– 22
ENGLISHDVCPRO I/F modeVIDEO OUT
MONITOR OUTAUDIO OUT
HEADPHONE
Output stop
Output stop
Output stop
Output stopEE (LINE/S-VIDEO)
Black
TAPE
TAPETAPE
TAPE
EE (AUDIO IN)
EE (AUDIO IN)
Output stop
Output stopEE (LINE/S-VIDEO)
BlackEE (AUDIO IN)
EE (AUDIO IN) 
						

							E– 23
RS-232C
The RS-232C commands are changed as set forth below by
installing the AJ-YAD250P in the AJ-D250.
$Edit control commands
(AJ-D250 Operating Instructions: Page 50)
What is added to the command description notes
Sends data of
computerReturn data from
VTRDescription of command
[STX] EAD:m [ETX]
Parameters
m = 0: CH1 & CH2
1: CH1
2: CH2
No parameter:
CH1 & CH2[STX] EAD [ETX] Sets the VTR to the AUDIO
INSERT PAUSE mode.
When the VTR is in the VIDEO
INSERT PAUSE mode, the
command sets it to the
AUDIO/VIDEO INSERT PAUSE
mode.  When it is in the REC
INHIBIT mode, error code
ER001 is returned from the VTR
and the VTR is set to the STOP
mode.

OThis command can be
accepted when the VTR is in
the PLAY PAUSE mode or
STILL mode.
OThe command is not
acknowledged when the
INPUT SELECT switch is at
the OPTION position.
What is
added 
						

							E– 24
ENGLISH
RS-232C
$Edit control commands
(AJ-D250 Operating Instructions: Page 50)
What is added to the command description notes
Sends data of
computerReturn data from
VTRDescription of command
[STX] EIN [ETX] [STX] EIN [ETX] Sets the VTR to the VIDEO
INSERT PAUSE mode.
When the VTR is in the AUDIO
INSERT PAUSE mode, the
command sets it to the
AUDIO/VIDEO INSERT PAUSE
mode.  When it is in the REC
INHIBIT mode, error code
ER001 is returned from the VTR
and the VTR is set to the STOP
mode.

OThis command can be
accepted when the VTR is in
the PLAY PAUSE mode or
STILL mode.
OThe command is not
acknowledged when the
INPUT SELECT switch is at
the OPTION position.
What is
added 
						

							E– 25
RS-232C
$Input/output control commands
(AJ-D250 Operating Instructions: Page 51)
Sends data of
computerReturn data from
VTR
Description of command
[STX] IEV:data [ETX]Parameters
data = m1m2
m1 = 0
F :
Designates the
data of bit 7 to bit
4.
m2 = 0
F:
Designates the
data of bit 3 to bit
0.[STX] IEV [ETX]
Parameter m1 (HEX display) m2 (HEX display)
Bits supportedBIT
7BIT
6BIT
5BIT
4BIT3
Switching data0000AUDIO
CH1
BIT2
AUDIO
CH2BIT1
VIDEOBIT0
TC
What is added to the command description notes
Forcibly switches to the E-E
(electric modulation to electric
playback) output.
When the V-V (VTR to VTR
recording) output is the picture
output status, it is forcibly
switched to the E-E output.
The forced E-E output is
released and the normal status
is restored by IEV:00.

OThis command is ignored
while a search control
command is being processed.
OThe command is not
acknowledged when the
INPUT SELECT switch is at
the OPTION position.
What is
added 
						

							E– 26
ENGLISH
RS-232C
What is added to the parameters used with data
transmitted by a personal computer
$Query control commands
(AJ-D250 Operating Instructions: Page 61)
Sends data of
computerReturn data from
VTRDescription of command
[STX] QRV:m [ETX]
Parameters
m =
A: AV system control
ROM version
S: Sub-code
microcomputer
version
C: Cylinder servo
ROM version
R: Reel servo ROM
version
I: Interface ROM
version
D: Digital video
interface board
ROM version
No parameter:
Interface ROM
version[STX] VERdata [ETX]data =
d1d2.d3d4-d5d6-
d7.d8d9
d1
d9:
Software program
versionQueries the software program
version used for each
microcomputer.
What is
added 
						

							E– 27
RS-232C
New commands which are added
Sends data of
computerReturn data from
VTRDescription of command
[STX] RPS:m [ETX]
Parameters
m =
1: 100 Mbps
2: 200 Mbps[STX] RPS [ETX] This sets the DVCPRO I/F
transmission rate.
[STX] RPI:data [ETX]
Parameters
data =
0x00
0x3F
(Input channel)[STX] RPI [ETX] This selects the DVCPRO I/F
input channel.
[STX] RPO:data [ETX]Parameters
data =
0x00
0x3F
(Output channel)[STX] RPO [ETX] This selects the DVCPRO I/F
output channel.
[STX] ADR:m [ETX]
Parameters
m =
S: STOP
E: ERASE[STX] ADR [ETX] This sets the mode when the
input data cannot be recorded.
[STX] RPK:data [ETX]
Parameters
data =
0x00
0xFF
(Configuration
number)[STX] RPK [ETX] This is the setting command for
an extended system.
For details, consult your dealer.
[STX] RPN:m [ETX]
Parameters
m =
N: ON
F: OFF[STX] RPN [ETX] This sets whether signals are to
be output to DVCPRO I/F in
cases where the input analog
signals are non-standard
signals. 
						

							E– 28
ENGLISH
RS-232C
New commands which are added
Sends data of
computerReturn data from
VTRDescription of command
[STX] QRP [ETX] [STX] RPSm [ETX]
Parameters
m =
1: 100 Mbps
2: 200 MbpsThis queries the DVCPRO I/F
transmission rate.
[STX] QRI [ETX][STX] RPIdata [ETX]Parameters
data =
0x00
0x3F
(Input channel)This queries the DVCPRO I/F
input channel.
[STX] QRO [ETX][STX] RPOdata [ETX]Parameters
data =
0x00
0x3F
(Output channel)This queries the DVCPRO I/F
output channel.
[STX] QAR [ETX] [STX] ADRm [ETX]
Parameters
m =
S: STOP
E: ERASEThis queries the mode when the
input data cannot be recorded.
[STX] QRK [ETX][STX] RPKdata [ETX]Parameters
data =
0x00
0xFF
(Configuration
number)This is the query command for
an extended system.
[STX] QRN [ETX] [STX] RPNm [ETX]
Parameters
m =
N: ON
F: OFFThis queries whether signals are
to be output to DVCPRO I/F in
cases where the input analog
signals are non-standard
signals. 
						

							E– 29
Error Messages
The following error messages are added by installing the AJ-
YAD250P in the AJ-D250.
E – 02This appears on the front panel while ERASE (all data
erase) is being executed.  In addition, “E” is displayed on
the first row (counter value display area) on the monitor
screen.
When T&S&R has been selected as the setup menu
No.001 (DISPLAY SEL) setting, “ERASE” is displayed on
the third row (remaining tape display area) on the
superimposed screen, and “--:--:--:--” appears as the
counter value.
E – 19This appears on the front panel for 5 seconds when the
INPUT SELECT switch has been set to the OPTION
position and the IEV command has been executed during
play or when the EIN or EAD command has been executed
in the PLAY PAUSE or SEARCH 0 speed mode.
In addition, “I” is displayed on the first row (counter value
display area) on the monitor screen.
When T&S&R has been selected as the setup menu
No.001 (DISPLAY SEL) setting, “INVALID PREVIEW” or
“INSERT INVALID” is displayed on the third row (remaining
tape display area) on the superimposed screen. Error No. Description