Panasonic Aj Yad250 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj Yad250 Operating Instructions Manual. The Panasonic manuals for Computer Equipment are available online for free. You can easily download all the documents as PDF.
Page 1
AJ- P Digital Video Interface Board Operating Instructions ENGLISH FRANÇAIS
Page 2
E– 1 This digital video interface board is designed to be used exclusively with the model AJ-D250 digital VTR. It cannot be used with model AJ-D230 or AJ-D230H. For details concerning its installation in the model AJ- D250, consult your dealer. Precautions ODo not touch the product with wet hands. ODo not drop the product or expose it to bumps or shocks. ODo not attempt to modify the product. Doing so could cause it to malfunction. Model supported Digital VTR: AJ-D250 CAUTION: TO REDUCE THE RISK OF FIRE...
Page 3
E– 2 ENGLISH Contents Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E– 1 Model supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E– 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E– 2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E– 3 RS-232C hardware specifications . . . . . . . . . . . . . . . . . . E– 4 Checking the software version . . . . . . . . . . . . . . . . . . . ....
Page 4
E– 3 Specifications $Digital video interface board Dimensions (Wa Ha D) : 6 3/16˝a 4 3/16˝a 1 1/16˝ (157a 105a 26 mm) Weight :0.3036 lb (138 g) Power consumption :2 W OItems packed with board Display label 9-pin/25-pin conversion connector Hexagonal head screws (for metric screw threads) Concerning which hexagonal head screws are to be used The accessory 9-pin/25-pin conversion connector comes with two hexagonal head screws for inch-standard screw threads. If metric screw threads are used by the device...
Page 5
E– 4 ENGLISH RS-232C hardware specifications External interface specifications Connector: D-SUB, 9 pins, DCE specifications (straight cable supported) For details on other specifications relating to RS-232C, refer to the operating instructions of the AJ-D250. Pin No. Signal Description 2RD (RXD) Received data 3SD (TXD) Transmitted data 4ER (DTR) Data terminal ready 5SG (GND) Signal ground 6DR (DSR) Data set ready 7RS (RTS) Request to send 8CS (CTS) Clear to send 2 RD (RXD) 3 SD (TXD) 4 ER (DTR) 5 SG...
Page 6
E– 5 IF : 1.04-00-0.00 AVSYS : 1.06-00-0.00 : : : : Checking the software version Check the software version of the AJ-D250 before installing the AJ-YAD250P in the AJ-D250. If it is an old version, it must be upgraded. Please consult your dealer. How to check to the software version 1.Connect a monitor to the AJ-D250. 2.Set the LOCAL/MENU/REMOTE switch to the MENU position while pressing the EJECT button on the front panel of the AJ-D250. 3.Press the FF (UP) button while pressing the REW (MODE) button....
Page 7
E– 6 ENGLISH Installing the board in an AJ-D250 In order for this product to be used, it must first be installed in an AJ-D250. Follow the installation procedure below. OAlways be absolutely sure to disconnect the AJ-D250’s power cord before proceeding with installation. 1.Remove the two screws on the top panel of the AJ-D250, and slide it toward the front panel to remove it. 2.Remove the three screws and remove the board clamp. Screws Board clampTop panel Screws
Page 8
E– 7 3.Disconnect the flat cable from the connector (P6001) on the RS-232C board, and remove the mounting screw to remove the RS-232C board. Mounting screw Flat cable RS-232C board
Page 9
E– 8 ENGLISH 4.Insert the AJ-YAD250P at the position previously occupied by the RS-232C board, and use the mounting screw to secure it in place. OTake care not to alter the position of the knob on SW103 when inserting the interface board. OIf it is difficult to insert the AJ-YAD250P, loosen screw (A) on the rear panel then insert it again. Be sure to tighten screw (A) after installing the AJ- YAD250P. (A) SW103 Mounting screw AJ-YAD250P Knob (Face of the part)
Page 10
E– 9 6.Install the board clamp, and attach the top panel. (Be absolutely sure to install the panel properly using the screws provided.) Board clamp Top panel 5.Connect the flat cable coming from the connector (P1101) on the AV SYSCON board to the connector (P101) on the AJ-YAD250P board. P101 P1101