Panasonic Aj D250 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj D250 Operating Instructions Manual. The Panasonic manuals for Cassette Player are available online for free. You can easily download all the documents as PDF.
Page 61
![Page 61
61
RS-232C
$Query control commands
Sends data of computer Return data from VTRDescription of command
[STX] QOS [ETX] [STX] OPSdata [ETX]
data = AD0AD1AD2AD3AD4
Refer to the bitmap table (B) for details
of AD
.Queries the operation modes.
The current VTR mode is detected and sent by the bitmap
information. The bitmap information is converted into ASCII
code and returned by the VTR.
[STX] QRA [ETX] [STX] RAm [ETX]
m = N: ACK ON
F: ACK OFFQueries the ACK (Acknowledge) code response setting.
[STX] QRS...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-60.png "Page 61
61
RS-232C
$Query control commands
Sends data of computer Return data from VTRDescription of command
[STX] QOS [ETX] [STX] OPSdata [ETX]
data = AD0AD1AD2AD3AD4
Refer to the bitmap table (B) for details
of AD
.Queries the operation modes.
The current VTR mode is detected and sent by the bitmap
information. The bitmap information is converted into ASCII
code and returned by the VTR.
[STX] QRA [ETX] [STX] RAm [ETX]
m = N: ACK ON
F: ACK OFFQueries the ACK (Acknowledge) code response setting.
[STX] QRS...")
61 RS-232C $Query control commands Sends data of computer Return data from VTRDescription of command [STX] QOS [ETX] [STX] OPSdata [ETX] data = AD0AD1AD2AD3AD4 Refer to the bitmap table (B) for details of AD .Queries the operation modes. The current VTR mode is detected and sent by the bitmap information. The bitmap information is converted into ASCII code and returned by the VTR. [STX] QRA [ETX] [STX] RAm [ETX] m = N: ACK ON F: ACK OFFQueries the ACK (Acknowledge) code response setting. [STX] QRS...
Page 62
62 RS-232C OBitmap table (B) ADDRESS BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 AD 0FULL EE SELECT EE 0 0 0 0TAPE END ()TAPE TOP () AD 1SHORT PLAY 0 STANDBY 0 0 0 0 SERVO LOCK AD 2REC INHIBIT TABCASSETTE IN/OUT0 VTR STATUS AD 3TAPE DIRECTIONSHUTTLE SPEED AD 40INSERT VIDEOINSERT AUDIO CH1INSERT AUDIO CH20000 VTR STATUS DATA BIT4BIT0VTR STATUS 1, 1, 1, 1, 1INSERT PAUSEBIT4 BIT0VTR STATUS 0, 1, 0, 0, 1PLAY PAUSE 0, 1, 0, 0, 0PLAY 0, 0, 0, 1, 1FAST FORWARD 0, 0, 0, 1, 0REWIND 0, 0, 0, 0, 1EJECT 0, 0, 0, 0,...
Page 63
![Page 63
63
RS-232C
$Query control commands
Sends data of computer Return data from VTRDescription of command
[STX] QSP:m [ETX]
Parameters
m =
B: BEGIN point
E: END point[STX] SMPdata [ETX]
data = pw:ghmmssff
OWhen CTL data is to be used as
the reference
pw = BP: BEGIN point
EP: END point
g = Blank: With a positive value
– sign: With a negative value
h = 0
9: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames
OWhen TC data is to be used as the
reference
pw = BP: BEGIN point
EP: END point
gh = 00
23:...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-62.png "Page 63
63
RS-232C
$Query control commands
Sends data of computer Return data from VTRDescription of command
[STX] QSP:m [ETX]
Parameters
m =
B: BEGIN point
E: END point[STX] SMPdata [ETX]
data = pw:ghmmssff
OWhen CTL data is to be used as
the reference
pw = BP: BEGIN point
EP: END point
g = Blank: With a positive value
– sign: With a negative value
h = 0
9: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames
OWhen TC data is to be used as the
reference
pw = BP: BEGIN point
EP: END point
gh = 00
23:...")
63 RS-232C $Query control commands Sends data of computer Return data from VTRDescription of command [STX] QSP:m [ETX] Parameters m = B: BEGIN point E: END point[STX] SMPdata [ETX] data = pw:ghmmssff OWhen CTL data is to be used as the reference pw = BP: BEGIN point EP: END point g = Blank: With a positive value – sign: With a negative value h = 0 9: Hours mm = 0059: Minutes ss = 0059: Seconds ff = 0029: Frames OWhen TC data is to be used as the reference pw = BP: BEGIN point EP: END point gh = 00 23:...
Page 64
![Page 64
64
RS-232C
$Communication control commands
Sends data of computer Return data from VTRDescription of command
[STX] RAN [ETX] [STX] RAN [ETX] Enables the return of the ACK (Acknowledge) code.
This command is ignored while a search control command
is being processed.
[STX] RAF [ETX] [STX] RAF [ETX] Disables the return of the ACK (Acknowledge) code.
This command is ignored while a search control command
is being processed.
[STX] RCK [ETX] [STX] RCK [ETX] Checks whether communication is established.
This...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-63.png "Page 64
64
RS-232C
$Communication control commands
Sends data of computer Return data from VTRDescription of command
[STX] RAN [ETX] [STX] RAN [ETX] Enables the return of the ACK (Acknowledge) code.
This command is ignored while a search control command
is being processed.
[STX] RAF [ETX] [STX] RAF [ETX] Disables the return of the ACK (Acknowledge) code.
This command is ignored while a search control command
is being processed.
[STX] RCK [ETX] [STX] RCK [ETX] Checks whether communication is established.
This...")
64 RS-232C $Communication control commands Sends data of computer Return data from VTRDescription of command [STX] RAN [ETX] [STX] RAN [ETX] Enables the return of the ACK (Acknowledge) code. This command is ignored while a search control command is being processed. [STX] RAF [ETX] [STX] RAF [ETX] Disables the return of the ACK (Acknowledge) code. This command is ignored while a search control command is being processed. [STX] RCK [ETX] [STX] RCK [ETX] Checks whether communication is established. This...
Page 65
![Page 65
65
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SCP:data [ETX]
Parameters
data = ghmmssff
OWhen CTL data is to be used
as the reference
g = Blank: With a positive value
– sign: With a negative value
h = 0
9: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames
OWhen TC data is to be used as
the reference
gh = 00
23: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames[STX] SCP [ETX] Searches the counter value which was...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-64.png "Page 65
65
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SCP:data [ETX]
Parameters
data = ghmmssff
OWhen CTL data is to be used
as the reference
g = Blank: With a positive value
– sign: With a negative value
h = 0
9: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames
OWhen TC data is to be used as
the reference
gh = 00
23: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames[STX] SCP [ETX] Searches the counter value which was...")
65 RS-232C $Search control commands Sends data of computer Return data from VTRDescription of command [STX] SCP:data [ETX] Parameters data = ghmmssff OWhen CTL data is to be used as the reference g = Blank: With a positive value – sign: With a negative value h = 0 9: Hours mm = 0059: Minutes ss = 0059: Seconds ff = 0029: Frames OWhen TC data is to be used as the reference gh = 00 23: Hours mm = 0059: Minutes ss = 0059: Seconds ff = 0029: Frames[STX] SCP [ETX] Searches the counter value which was...
Page 66
![Page 66
66
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SMI:data [ETX]
Parameters
data = wwghmmssff
OWhen the counter value is to
be stored in the memory
ww = LC: CTL data reference
SC: TC data reference
“ghmmssff” is omitted.
OWhen the parameter value for
which the CTL data serves as
the reference is to be stored in
the memory
ww = LP: CTL data reference
g = Blank: With a positive value
– sign: With a negative value
h = 0
9: Hours
mm = 0059: Minutes
ss...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-65.png "Page 66
66
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SMI:data [ETX]
Parameters
data = wwghmmssff
OWhen the counter value is to
be stored in the memory
ww = LC: CTL data reference
SC: TC data reference
“ghmmssff” is omitted.
OWhen the parameter value for
which the CTL data serves as
the reference is to be stored in
the memory
ww = LP: CTL data reference
g = Blank: With a positive value
– sign: With a negative value
h = 0
9: Hours
mm = 0059: Minutes
ss...")
66 RS-232C $Search control commands Sends data of computer Return data from VTRDescription of command [STX] SMI:data [ETX] Parameters data = wwghmmssff OWhen the counter value is to be stored in the memory ww = LC: CTL data reference SC: TC data reference “ghmmssff” is omitted. OWhen the parameter value for which the CTL data serves as the reference is to be stored in the memory ww = LP: CTL data reference g = Blank: With a positive value – sign: With a negative value h = 0 9: Hours mm = 0059: Minutes ss...
Page 67
![Page 67
67
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SMP:data [ETX]
Parameters
data = pww:ghmmssff
OWhen the counter value is to
be stored in the memory
p = B: BEGIN point
E: END point
ww = LC: CTL data reference
SC: TC data reference
“ghmmssff” is omitted.
OWhen the parameter value for
which the CTL data serves as
the reference is to be stored in
the memory
p = B: BEGIN point
E: END point
ww = LP: CTL data reference
g = Blank: With a positive value...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-66.png "Page 67
67
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SMP:data [ETX]
Parameters
data = pww:ghmmssff
OWhen the counter value is to
be stored in the memory
p = B: BEGIN point
E: END point
ww = LC: CTL data reference
SC: TC data reference
“ghmmssff” is omitted.
OWhen the parameter value for
which the CTL data serves as
the reference is to be stored in
the memory
p = B: BEGIN point
E: END point
ww = LP: CTL data reference
g = Blank: With a positive value...")
67 RS-232C $Search control commands Sends data of computer Return data from VTRDescription of command [STX] SMP:data [ETX] Parameters data = pww:ghmmssff OWhen the counter value is to be stored in the memory p = B: BEGIN point E: END point ww = LC: CTL data reference SC: TC data reference “ghmmssff” is omitted. OWhen the parameter value for which the CTL data serves as the reference is to be stored in the memory p = B: BEGIN point E: END point ww = LP: CTL data reference g = Blank: With a positive value...
Page 68
![Page 68
68
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SMS [ETX] [STX] SMS [ETX] Searches the counter value at the time when the command
stored in the memory was received.
The STILL mode is established upon completion of the
search.
If the designated position is an illegal position (the target
position does not exist), error code ER122 will be returned
from the VTR which is then set to the STOP mode.
When the OSP (STOP) command or OEJ (tape EJECT)...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-67.png "Page 68
68
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SMS [ETX] [STX] SMS [ETX] Searches the counter value at the time when the command
stored in the memory was received.
The STILL mode is established upon completion of the
search.
If the designated position is an illegal position (the target
position does not exist), error code ER122 will be returned
from the VTR which is then set to the STOP mode.
When the OSP (STOP) command or OEJ (tape EJECT)...")
68 RS-232C $Search control commands Sends data of computer Return data from VTRDescription of command [STX] SMS [ETX] [STX] SMS [ETX] Searches the counter value at the time when the command stored in the memory was received. The STILL mode is established upon completion of the search. If the designated position is an illegal position (the target position does not exist), error code ER122 will be returned from the VTR which is then set to the STOP mode. When the OSP (STOP) command or OEJ (tape EJECT)...
Page 69
![Page 69
69
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SRS:data [ETX]
Parameters
data = wghmmssff
OWhen CTL data is to be used
as the reference
w = L: CTL data reference
g = Blank: With a positive value
– sign: With a negative value
h = 0
9: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames
OWhen TC data is to be used as
the reference
w = S: TC data reference
gh = 00
23: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames[STX] SRS...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-68.png "Page 69
69
RS-232C
$Search control commands
Sends data of computer Return data from VTRDescription of command
[STX] SRS:data [ETX]
Parameters
data = wghmmssff
OWhen CTL data is to be used
as the reference
w = L: CTL data reference
g = Blank: With a positive value
– sign: With a negative value
h = 0
9: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames
OWhen TC data is to be used as
the reference
w = S: TC data reference
gh = 00
23: Hours
mm = 0059: Minutes
ss = 0059: Seconds
ff = 0029: Frames[STX] SRS...")
69 RS-232C $Search control commands Sends data of computer Return data from VTRDescription of command [STX] SRS:data [ETX] Parameters data = wghmmssff OWhen CTL data is to be used as the reference w = L: CTL data reference g = Blank: With a positive value – sign: With a negative value h = 0 9: Hours mm = 0059: Minutes ss = 0059: Seconds ff = 0029: Frames OWhen TC data is to be used as the reference w = S: TC data reference gh = 00 23: Hours mm = 0059: Minutes ss = 0059: Seconds ff = 0029: Frames[STX] SRS...
Page 70
![Page 70
70
RS-232C
$Timer control commands
Sends data of computer Return data from VTRDescription of command
[STX] TST:data [ETX]
Parameters
data = mmmm
mmmm =
0000: 0.5 sec.
0005: 5 sec.
0010: 10 sec.
0030: 30 sec.
0100: 1 min.
0200: 2 min.[STX] TST [ETX] Sets the standby OFF timer.
This command is ignored while a search control command
is being processed.](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-69.png "Page 70
70
RS-232C
$Timer control commands
Sends data of computer Return data from VTRDescription of command
[STX] TST:data [ETX]
Parameters
data = mmmm
mmmm =
0000: 0.5 sec.
0005: 5 sec.
0010: 10 sec.
0030: 30 sec.
0100: 1 min.
0200: 2 min.[STX] TST [ETX] Sets the standby OFF timer.
This command is ignored while a search control command
is being processed.")
70 RS-232C $Timer control commands Sends data of computer Return data from VTRDescription of command [STX] TST:data [ETX] Parameters data = mmmm mmmm = 0000: 0.5 sec. 0005: 5 sec. 0010: 10 sec. 0030: 30 sec. 0100: 1 min. 0200: 2 min.[STX] TST [ETX] Sets the standby OFF timer. This command is ignored while a search control command is being processed.