Panasonic Aj D250 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj D250 Operating Instructions Manual. The Panasonic manuals for Cassette Player are available online for free. You can easily download all the documents as PDF.
Page 31
31 TAPE PROTECT menu The underlining denotes the factory mode setting. When a consumer-use DV format tape is used, the tape protection mode will be established in 10 seconds even if 30s, 1min or 2min is selected as the STILL TIMER item setting. Setup Menus Item Setting No.Superimposed displayNo.Superimposed displayDescription of setting 400 STILL TIMER 0000 0001 0002 0003 0004 00050.5s 5s 10s 30s 1min 2minFor selecting the time taken for the tape protection mode to be established when the unit has been...
Page 32
32 TIME CODE menu The underlining denotes the factory mode setting. Setup Menus Item Setting No.Superimposed displayNo.Superimposed displayDescription of setting 500 VITC POS-1 0000 0001 0006 001010L 11L 16L 20L For setting the position where the VITC signal is to be inserted. (The same line as the one set for the VITC POS-2 item cannot be selected.) 501 VITC POS-2 0000 0001 0008 001010L 11L 18L 20L For setting the position where the VITC signal is to be inserted. (The same line as the one set for the...
Page 33
33 VIDEO menu The underlining denotes the factory mode setting. Setup Menus Item Setting No.Superimposed displayNo.Superimposed displayDescription of setting 600 VIDEO MODE 0000 0001B/W COLORFor setting the recording and playback of the video signals. 0: When monochrome signals are used 1: When color signals are used OSet this item to the B/W mode when monochrome signals are to be recorded or played back. Set the item to the COLOR mode with regular color signals. OIf color signals are recorded in the...
Page 34
34 Setup Menus AUDIO menu The underlining denotes the factory mode setting. Item Setting No.Superimposed displayNo.Superimposed displayDescription of setting 700 AUDIO EDIT IN 0000 0001 CUTFADE For selecting the joining method at the IN point during digital audio editing. 0: Cutting 1: Fading 701 AUDIO EDIT OUT 0000 0001 CUTFADE For selecting the joining method at the OUT point during digital audio editing. 0: Cutting 1: Fading 702 PB FADE 0000 0001 0002AUTOCUT FADE For selecting the processing to be...
Page 35
35 Editing Editing with the RS-232C remote control OUTPUT INPUT Using the RS-232C remote control (AJ-A250), which is available as an optional accessory, two units—a player VTR and a recorder VTR—can be controlled directly from the controller to enable speedier and more efficient assemble editing, insert editing and other editing jobs. To RS-232C connectorPlayer VTR: AJ-D250 Recorder VTR: AJ-D250 RS-232C remote control (AJ-A250)To RS-232C connector Read the operating instructions of the AJ-A250...
Page 36
36 Audio editing functions The information (setup menu item No. 700, 701) concerning the selection of the joining method used at the edit points is recorded during digital audio editing, and this information is detected during playback so that the edit points can be processed automatically. This applies only when AUTO has been selected as the playback fade selection (setup menu item No.702) setting. OWhen CUT has been selected for the playback fade selection (setup menu item No.702), cutting will be...
Page 37
37 First Edit Function (Preparing the editing tape) The CTL (control) signal must be recorded ahead of time onto the editing tape. The method used to record it differs depending on whether assemble editing or insert editing is to be performed. The “E-00” servo lock error appears on the tape counter when insert editing is performed for a tape on which the CTL signal has not been recorded. When insert editing is performed, the CTL signal must be recorded ahead of time. When first edit is to be performed,...
Page 38
38 1. Hardware specifications (1) Interface specifications Connector: D-SUB 25 pins DCE specifications (straight cable supported) Pin No. Signal Description 1 FG Frame GND 2 SD (TXD) Transmitted Data 3 RD (RXD) Received Data 4 RS (RTS) Request to Send 5 CD (CTS) Clear to Send 6 DR (DSR) Data Set Ready 7 SG Signal GND 20 ER (DTR) Data Terminal Ready Example of connections (2) Communication parameters The unit’s communication parameters are as listed below. If any of the parameters are to be changed,...
Page 39
![Page 39
39
2. Software specifications
(1) External interface specifications
Communication
systemAsynchronous system, full duplex
Baud rate1200, 2400, 4800, 9600 or 19200 bps
Bit length8 bits or 7 bits
Stop bit1 bit or 2 bits
ParityNone, odd or even
OThe factory settings are 9600 bps, 8 bits, 1 stop bit
and none as the parity.
OThe unit has a 127-byte receive buffer.
(2) Sending format (computer VTR)
$Data format
[STX] [discrimination] [:] [data] [ETX]
02H XX XX XX 3AH XX.....
XX 03H
20H](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-38.png "Page 39
39
2. Software specifications
(1) External interface specifications
Communication
systemAsynchronous system, full duplex
Baud rate1200, 2400, 4800, 9600 or 19200 bps
Bit length8 bits or 7 bits
Stop bit1 bit or 2 bits
ParityNone, odd or even
OThe factory settings are 9600 bps, 8 bits, 1 stop bit
and none as the parity.
OThe unit has a 127-byte receive buffer.
(2) Sending format (computer VTR)
$Data format
[STX] [discrimination] [:] [data] [ETX]
02H XX XX XX 3AH XX.....
XX 03H
20H")
39 2. Software specifications (1) External interface specifications Communication systemAsynchronous system, full duplex Baud rate1200, 2400, 4800, 9600 or 19200 bps Bit length8 bits or 7 bits Stop bit1 bit or 2 bits ParityNone, odd or even OThe factory settings are 9600 bps, 8 bits, 1 stop bit and none as the parity. OThe unit has a 127-byte receive buffer. (2) Sending format (computer VTR) $Data format [STX] [discrimination] [:] [data] [ETX] 02H XX XX XX 3AH XX..... XX 03H 20H
Page 40
![Page 40
40
RS-232C
2) If there were errors in the data or any problems
in the VTR, a description of the reason why the
data was not received is returned in the following
format.
[STX] E R 0 0
)[ETX]
02H 45H 52H 30H 30H XX 03H
OContents of
)
1 (31H): A command which is not supported or a
command execution error
2 (32H): Erroneous parameter with the wrong
data code
3 (33H): Receive buffer overflow error
[STX] E R 1 0
)[ETX]
02H 45H 52H 31H 30H XX 03H
OContents of
)
2 (32H): Front loading error
3 (33H): Loading...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-39.png "Page 40
40
RS-232C
2) If there were errors in the data or any problems
in the VTR, a description of the reason why the
data was not received is returned in the following
format.
[STX] E R 0 0
)[ETX]
02H 45H 52H 30H 30H XX 03H
OContents of
)
1 (31H): A command which is not supported or a
command execution error
2 (32H): Erroneous parameter with the wrong
data code
3 (33H): Receive buffer overflow error
[STX] E R 1 0
)[ETX]
02H 45H 52H 31H 30H XX 03H
OContents of
)
2 (32H): Front loading error
3 (33H): Loading...")
40 RS-232C 2) If there were errors in the data or any problems in the VTR, a description of the reason why the data was not received is returned in the following format. [STX] E R 0 0 )[ETX] 02H 45H 52H 30H 30H XX 03H OContents of ) 1 (31H): A command which is not supported or a command execution error 2 (32H): Erroneous parameter with the wrong data code 3 (33H): Receive buffer overflow error [STX] E R 1 0 )[ETX] 02H 45H 52H 31H 30H XX 03H OContents of ) 2 (32H): Front loading error 3 (33H): Loading...