Panasonic Aj D250 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj D250 Operating Instructions Manual. The Panasonic manuals for Cassette Player are available online for free. You can easily download all the documents as PDF.
Page 41
![Page 41
41
RS-232C
(4) Command list
$List of commands
The table below lists the send commands and operations for each mode as seen from the computer end.
[STX]= HEX code 02H
[ETX]= HEX code 03H
:= HEX code 3AH
The discrimination part and data part represent the ASCII codes which support the corresponding
symbols.
OAudio control commands
Sends data of computer Return data from VTRDescription of command
[STX] AOC:m [ETX] [STX] AOC [ETX] Sets the audio signal output channel.
OCounter control commands
Sends data of...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-40.png "Page 41
41
RS-232C
(4) Command list
$List of commands
The table below lists the send commands and operations for each mode as seen from the computer end.
[STX]= HEX code 02H
[ETX]= HEX code 03H
:= HEX code 3AH
The discrimination part and data part represent the ASCII codes which support the corresponding
symbols.
OAudio control commands
Sends data of computer Return data from VTRDescription of command
[STX] AOC:m [ETX] [STX] AOC [ETX] Sets the audio signal output channel.
OCounter control commands
Sends data of...")
41 RS-232C (4) Command list $List of commands The table below lists the send commands and operations for each mode as seen from the computer end. [STX]= HEX code 02H [ETX]= HEX code 03H := HEX code 3AH The discrimination part and data part represent the ASCII codes which support the corresponding symbols. OAudio control commands Sends data of computer Return data from VTRDescription of command [STX] AOC:m [ETX] [STX] AOC [ETX] Sets the audio signal output channel. OCounter control commands Sends data of...
Page 42
![Page 42
42
RS-232C
ODisplay control commands
Sends data of computer Return data from VTRDescription of command
[STX] DFC:m [ETX] [STX] DFC [ETX] Sets the display mode of the display counter.
OInput/output control commands
Sends data of computer Return data from VTRDescription of command
[STX] IEV:data [ETX] [STX] IEV [ETX]Switches between E-E and V-V output.
E-E: Electric modulation to electric playback
V-V: VTR to VTR recording
OEdit control commands
Sends data of computer Return data from VTRDescription of...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-41.png "Page 42
42
RS-232C
ODisplay control commands
Sends data of computer Return data from VTRDescription of command
[STX] DFC:m [ETX] [STX] DFC [ETX] Sets the display mode of the display counter.
OInput/output control commands
Sends data of computer Return data from VTRDescription of command
[STX] IEV:data [ETX] [STX] IEV [ETX]Switches between E-E and V-V output.
E-E: Electric modulation to electric playback
V-V: VTR to VTR recording
OEdit control commands
Sends data of computer Return data from VTRDescription of...")
42 RS-232C ODisplay control commands Sends data of computer Return data from VTRDescription of command [STX] DFC:m [ETX] [STX] DFC [ETX] Sets the display mode of the display counter. OInput/output control commands Sends data of computer Return data from VTRDescription of command [STX] IEV:data [ETX] [STX] IEV [ETX]Switches between E-E and V-V output. E-E: Electric modulation to electric playback V-V: VTR to VTR recording OEdit control commands Sends data of computer Return data from VTRDescription of...
Page 43
![Page 43
43
RS-232C
OOperation control commands
Sends data of computer Return data from VTRDescription of command
[STX] OAF [ETX] [STX] OAF [ETX] Advances frames in the forward direction.
[STX] OAR [ETX] [STX] OAR [ETX] Advances frames in the reverse direction.
[STX] OBF [ETX] [STX] OBF [ETX] STANDBY OFF
[STX] OBN [ETX] [STX] OBN [ETX] STANDBY ON
[STX] OEJ [ETX] [STX] OEJ [ETX] EJECT
[STX] OFF [ETX] [STX] OFF [ETX] FAST FORWARD
[STX] OPA [ETX] [STX] OPA [ETX] PAUSE
[STX] OPL [ETX] [STX] OPL [ETX] PLAY
[STX] OPR...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-42.png "Page 43
43
RS-232C
OOperation control commands
Sends data of computer Return data from VTRDescription of command
[STX] OAF [ETX] [STX] OAF [ETX] Advances frames in the forward direction.
[STX] OAR [ETX] [STX] OAR [ETX] Advances frames in the reverse direction.
[STX] OBF [ETX] [STX] OBF [ETX] STANDBY OFF
[STX] OBN [ETX] [STX] OBN [ETX] STANDBY ON
[STX] OEJ [ETX] [STX] OEJ [ETX] EJECT
[STX] OFF [ETX] [STX] OFF [ETX] FAST FORWARD
[STX] OPA [ETX] [STX] OPA [ETX] PAUSE
[STX] OPL [ETX] [STX] OPL [ETX] PLAY
[STX] OPR...")
43 RS-232C OOperation control commands Sends data of computer Return data from VTRDescription of command [STX] OAF [ETX] [STX] OAF [ETX] Advances frames in the forward direction. [STX] OAR [ETX] [STX] OAR [ETX] Advances frames in the reverse direction. [STX] OBF [ETX] [STX] OBF [ETX] STANDBY OFF [STX] OBN [ETX] [STX] OBN [ETX] STANDBY ON [STX] OEJ [ETX] [STX] OEJ [ETX] EJECT [STX] OFF [ETX] [STX] OFF [ETX] FAST FORWARD [STX] OPA [ETX] [STX] OPA [ETX] PAUSE [STX] OPL [ETX] [STX] OPL [ETX] PLAY [STX] OPR...
Page 44
![Page 44
44
RS-232C
OQuery control commands
Sends data of computer Return data from VTRDescription of command
[STX] QAL [ETX] [STX] ALV0 [ETX] Queries the address level.
[STX] QAO [ETX] [STX] AOm [ETX] Queries the audio output channels.
[STX] QCA [ETX] [STX] CUPdata [ETX] Queries the user’s bit data which was preset in the TCG.
[STX] QCB [ETX] [STX] CUSdata [ETX] Queries the user’s bit data of the TCG.
[STX] QCC [ETX] [STX] CCPdata [ETX] Queries the counter data (same as QCD).
[STX] QCD [ETX] [STX] CDdata [ETX]...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-43.png "Page 44
44
RS-232C
OQuery control commands
Sends data of computer Return data from VTRDescription of command
[STX] QAL [ETX] [STX] ALV0 [ETX] Queries the address level.
[STX] QAO [ETX] [STX] AOm [ETX] Queries the audio output channels.
[STX] QCA [ETX] [STX] CUPdata [ETX] Queries the user’s bit data which was preset in the TCG.
[STX] QCB [ETX] [STX] CUSdata [ETX] Queries the user’s bit data of the TCG.
[STX] QCC [ETX] [STX] CCPdata [ETX] Queries the counter data (same as QCD).
[STX] QCD [ETX] [STX] CDdata [ETX]...")
44 RS-232C OQuery control commands Sends data of computer Return data from VTRDescription of command [STX] QAL [ETX] [STX] ALV0 [ETX] Queries the address level. [STX] QAO [ETX] [STX] AOm [ETX] Queries the audio output channels. [STX] QCA [ETX] [STX] CUPdata [ETX] Queries the user’s bit data which was preset in the TCG. [STX] QCB [ETX] [STX] CUSdata [ETX] Queries the user’s bit data of the TCG. [STX] QCC [ETX] [STX] CCPdata [ETX] Queries the counter data (same as QCD). [STX] QCD [ETX] [STX] CDdata [ETX]...
Page 45
![Page 45
45
RS-232C
OQuery control commands
Sends data of computer Return data from VTRDescription of command
[STX] QLH:m [ETX] [STX] LHRdata [ETX] Queries the hours meter.
[STX] QOT [ETX] [STX] OTEm [ETX] Queries the E-E output and V-V output.
[STX] QOP [ETX] [STX] data [ETX] Queries the VTR’s operation mode.
[STX] QOD:d1d2 [ETX] [STX] OASdata [ETX] Queries the operation modes.
[STX] QOS [ETX] [STX] OPSdata [ETX] Queries the operation modes.
[STX] QRA [ETX] [STX] RAm [ETX] Queries the ACK (Acknowledge) code...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-44.png "Page 45
45
RS-232C
OQuery control commands
Sends data of computer Return data from VTRDescription of command
[STX] QLH:m [ETX] [STX] LHRdata [ETX] Queries the hours meter.
[STX] QOT [ETX] [STX] OTEm [ETX] Queries the E-E output and V-V output.
[STX] QOP [ETX] [STX] data [ETX] Queries the VTR’s operation mode.
[STX] QOD:d1d2 [ETX] [STX] OASdata [ETX] Queries the operation modes.
[STX] QOS [ETX] [STX] OPSdata [ETX] Queries the operation modes.
[STX] QRA [ETX] [STX] RAm [ETX] Queries the ACK (Acknowledge) code...")
45 RS-232C OQuery control commands Sends data of computer Return data from VTRDescription of command [STX] QLH:m [ETX] [STX] LHRdata [ETX] Queries the hours meter. [STX] QOT [ETX] [STX] OTEm [ETX] Queries the E-E output and V-V output. [STX] QOP [ETX] [STX] data [ETX] Queries the VTR’s operation mode. [STX] QOD:d1d2 [ETX] [STX] OASdata [ETX] Queries the operation modes. [STX] QOS [ETX] [STX] OPSdata [ETX] Queries the operation modes. [STX] QRA [ETX] [STX] RAm [ETX] Queries the ACK (Acknowledge) code...
Page 46
![Page 46
46
RS-232C
OSearches control commands
Sends data of computer Return data from VTRDescription of command
[STX] SCP:data [ETX] [STX] SCP [ETX] Searches the counter value and play.
OTimer control commands
Sends data of computer Return data from VTRDescription of command
[STX] TST:data [ETX] [STX] TST [ETX] Sets the standby off timer.
[STX] SCS:data [ETX] [STX] SCS [ETX]Searches the counter value and sets to still picture (same
as SRS).
[STX] SMI:data [ETX] [STX] SMI [ETX] Sets the memory search data.
[STX]...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-45.png "Page 46
46
RS-232C
OSearches control commands
Sends data of computer Return data from VTRDescription of command
[STX] SCP:data [ETX] [STX] SCP [ETX] Searches the counter value and play.
OTimer control commands
Sends data of computer Return data from VTRDescription of command
[STX] TST:data [ETX] [STX] TST [ETX] Sets the standby off timer.
[STX] SCS:data [ETX] [STX] SCS [ETX]Searches the counter value and sets to still picture (same
as SRS).
[STX] SMI:data [ETX] [STX] SMI [ETX] Sets the memory search data.
[STX]...")
46 RS-232C OSearches control commands Sends data of computer Return data from VTRDescription of command [STX] SCP:data [ETX] [STX] SCP [ETX] Searches the counter value and play. OTimer control commands Sends data of computer Return data from VTRDescription of command [STX] TST:data [ETX] [STX] TST [ETX] Sets the standby off timer. [STX] SCS:data [ETX] [STX] SCS [ETX]Searches the counter value and sets to still picture (same as SRS). [STX] SMI:data [ETX] [STX] SMI [ETX] Sets the memory search data. [STX]...
Page 47
![Page 47
47
RS-232C
$Audio control commands
Sends data of computer Return data from VTRDescription of command
[STX] AOC:m [ETX]
Parameters
m = 1: CH1
2: CH2
3: CH3
4: CH4
5: CH1 & CH2
6: CH3 & CH4
7: CH1+3 & CH2+4[STX] AOC [ETX] Sets the audio signal output channel/s. Playback output is
possible for CH3 and CH4 when audio signals for 4
channels have been recorded on a DV format tape.
This command is ignored while a search control command
is being processed.
$Counter control commands
Sends data of computer...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-46.png "Page 47
47
RS-232C
$Audio control commands
Sends data of computer Return data from VTRDescription of command
[STX] AOC:m [ETX]
Parameters
m = 1: CH1
2: CH2
3: CH3
4: CH4
5: CH1 & CH2
6: CH3 & CH4
7: CH1+3 & CH2+4[STX] AOC [ETX] Sets the audio signal output channel/s. Playback output is
possible for CH3 and CH4 when audio signals for 4
channels have been recorded on a DV format tape.
This command is ignored while a search control command
is being processed.
$Counter control commands
Sends data of computer...")
47 RS-232C $Audio control commands Sends data of computer Return data from VTRDescription of command [STX] AOC:m [ETX] Parameters m = 1: CH1 2: CH2 3: CH3 4: CH4 5: CH1 & CH2 6: CH3 & CH4 7: CH1+3 & CH2+4[STX] AOC [ETX] Sets the audio signal output channel/s. Playback output is possible for CH3 and CH4 when audio signals for 4 channels have been recorded on a DV format tape. This command is ignored while a search control command is being processed. $Counter control commands Sends data of computer...
Page 48
![Page 48
48
RS-232C
$Counter control commands
Sends data of computer Return data from VTRDescription of command
[STX] CRN:m [ETX]
Parameters
m = 0: TC & UB
1: TC
2: UB[STX] CRN [ETX] Sets the signal to be regenerated when the TCG (time code
generator) is set to the regeneration mode.
This command is ignored while a search control command
is being processed.
[STX] CTM:m [ETX]
Parameters
m = 0: REC RUN mode
1: FREE RUN mode
2: Regeneration mode
3: External VITC mode[STX] CTM [ETX] Sets the mode used by the TCG....](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-47.png "Page 48
48
RS-232C
$Counter control commands
Sends data of computer Return data from VTRDescription of command
[STX] CRN:m [ETX]
Parameters
m = 0: TC & UB
1: TC
2: UB[STX] CRN [ETX] Sets the signal to be regenerated when the TCG (time code
generator) is set to the regeneration mode.
This command is ignored while a search control command
is being processed.
[STX] CTM:m [ETX]
Parameters
m = 0: REC RUN mode
1: FREE RUN mode
2: Regeneration mode
3: External VITC mode[STX] CTM [ETX] Sets the mode used by the TCG....")
48 RS-232C $Counter control commands Sends data of computer Return data from VTRDescription of command [STX] CRN:m [ETX] Parameters m = 0: TC & UB 1: TC 2: UB[STX] CRN [ETX] Sets the signal to be regenerated when the TCG (time code generator) is set to the regeneration mode. This command is ignored while a search control command is being processed. [STX] CTM:m [ETX] Parameters m = 0: REC RUN mode 1: FREE RUN mode 2: Regeneration mode 3: External VITC mode[STX] CTM [ETX] Sets the mode used by the TCG....
Page 49
![Page 49
49
[STX] CTP [ETX] [STX] CTP [ETX] Uses the TCG in the preset mode.
The TCG starts counting up in the REC RUN mode upon
completion of the settings.
This command is ignored while a search control command
is being processed, during recording and in the INSERT
mode.
[STX] CTR [ETX] [STX] CTR [ETX] Uses the TCG in the regeneration mode.
This command is ignored while a search control command
is being processed, during recording and in the INSERT
mode.
RS-232C
$Counter control commands
Sends data of computer...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-48.png "Page 49
49
[STX] CTP [ETX] [STX] CTP [ETX] Uses the TCG in the preset mode.
The TCG starts counting up in the REC RUN mode upon
completion of the settings.
This command is ignored while a search control command
is being processed, during recording and in the INSERT
mode.
[STX] CTR [ETX] [STX] CTR [ETX] Uses the TCG in the regeneration mode.
This command is ignored while a search control command
is being processed, during recording and in the INSERT
mode.
RS-232C
$Counter control commands
Sends data of computer...")
49 [STX] CTP [ETX] [STX] CTP [ETX] Uses the TCG in the preset mode. The TCG starts counting up in the REC RUN mode upon completion of the settings. This command is ignored while a search control command is being processed, during recording and in the INSERT mode. [STX] CTR [ETX] [STX] CTR [ETX] Uses the TCG in the regeneration mode. This command is ignored while a search control command is being processed, during recording and in the INSERT mode. RS-232C $Counter control commands Sends data of computer...
Page 50
![Page 50
50
RS-232C
$Edit control commands
Sends data of computer Return data from VTRDescription of command
[STX] EAB:m [ETX]
Parameters
m = N: AUTO BACK ON
F: AUTO BACK OFF[STX] EAB [ETX] Sets whether auto back recording is to be performed to
ensure frame to frame continuity.
This command is ignored while a search control command
is being processed and during auto back.
[STX] EAD:m [ETX]
Parameters
m = 0: CH1 & CH2
1: CH1
2: CH2
No parameter: CH1 & CH2[STX] EAD [ETX] Sets the VTR to the AUDIO INSERT PAUSE...](http://img.usermanuals.tech/thumb/58/67898/w300_aj-d250_en_om_d-49.png "Page 50
50
RS-232C
$Edit control commands
Sends data of computer Return data from VTRDescription of command
[STX] EAB:m [ETX]
Parameters
m = N: AUTO BACK ON
F: AUTO BACK OFF[STX] EAB [ETX] Sets whether auto back recording is to be performed to
ensure frame to frame continuity.
This command is ignored while a search control command
is being processed and during auto back.
[STX] EAD:m [ETX]
Parameters
m = 0: CH1 & CH2
1: CH1
2: CH2
No parameter: CH1 & CH2[STX] EAD [ETX] Sets the VTR to the AUDIO INSERT PAUSE...")
50 RS-232C $Edit control commands Sends data of computer Return data from VTRDescription of command [STX] EAB:m [ETX] Parameters m = N: AUTO BACK ON F: AUTO BACK OFF[STX] EAB [ETX] Sets whether auto back recording is to be performed to ensure frame to frame continuity. This command is ignored while a search control command is being processed and during auto back. [STX] EAD:m [ETX] Parameters m = 0: CH1 & CH2 1: CH1 2: CH2 No parameter: CH1 & CH2[STX] EAD [ETX] Sets the VTR to the AUDIO INSERT PAUSE...