OKI MC860cdtn User Manual

Operation > 111
Using a Job Program:
To use a pre-programmed short cut:
1.Press the  Job Program  button on the control panel to prompt the  Job Programs 
screen.
2. Select the job number you wish to use.
3. At the prompt, select  Yes to execute the program or  No to exit.
Deleting a Job Program:
To delete a Job Program function:
1. Press the  Setup button on the control panel to prompt the  Setup screen.
2. Press the  Job Programs Setting  button.
3. Press the  Delete button.
4. Select the job number...

Operation > 112
Reports and Listings
Press the Reports button on the control panel to display the list of reporting options 
available:
Configuration
1. Press the  Configuration  button.
2. At the prompt, press  Yes to print the report or press  No to cancel the operation and 
return to the Reports screen.
Information
1. Press the  Information  button to display the information report and listing options.
2. Select required report or list:
- File List
-Demo Page
- Error Log
-Scan to Log
-MFP Usage...

Operation > 113
- Journal Report:(i) Fax Transmit
(ii) Fax Receive
(iii) Fax Tx/Rx
(iv) Journal Daily Report
-F-code Box List
-Block Junk Fax
- Store Doc List
3. At the prompt, press  Yes to print the report/list or press  No to cancel the operation 
and return to the list of fax reports.
Scan 
1. Press the  SCAN button.
2. Press the  E-mail Address  button.
3. At the prompt, press  Yes to print the list of e-mail addresses or press  No to cancel 
the operation.
Print
1. Press the  PRINT button to...

Maintenance > 114
Maintenance
Consumable Life Expectancy
As a guide, the life expectancy of these items is:
•Toner Starter cartridge:
The machine is shipped with sufficient cyan, magenta, yellow & black toner for 2,000 
images (ISO/IEC19798), of which 750 images are used to charge the image drum 
(1,250 A4 pages remaining at 5% coverage).
Replacement cartridge:
Replacement cartridges (C, M, Y & K)  have a capacity of approximately 10,000 
images (ISO/IEC19798).
• Image drum:  As the lifetime of the...

Maintenance > 115
Replacing Consumable Items
Toner Cartridge Replacement
The toner used in this machine is a very fine dry powder. It is contained in four cartridges: 
one each for cyan, magenta, yellow and black.
Have a sheet of paper handy so that you have  somewhere to place the used cartridge while 
you install the new one.
Dispose of the old cartridge responsibly, inside the pack that the new one came in.  Follow 
any regulations, recommendations, etc., which  may be in force concerning waste...

Maintenance > 116
2.Press the cover release (a) and open the top cover (b) fully.
3. Note the positions of the four cartridges. It  is essential that they go back in the same 
order.
5. Pull the colored toner release lever (1) on th e cartridge to be replaced fully towards 
the front of the MFP.
WARNING!
If the MFP has been powe red on, the fuser may be hot. This area is 
clearly labelled. Do not touch.
1. Cyan cartridge 3. Yellow cartridge
2. Magenta cartridge 4. Black cartridge
b
a
1 
2 
3 
4 
1...

Maintenance > 117
6.Lift the right-hand end of the cartridge an d then draw the cartridge to the right to 
release the left-hand end as shown, and wi thdraw the toner cartridge out of the MFP.
7. Put the cartridge down gently onto a piec e of paper to prevent toner from marking 
your furniture.
8. Remove the new cartridge from its box but leave its wrapping material in place for 
the moment.
9. Gently shake the new cartridge from end to end several times to loosen and 
distribute the toner evenly inside...

Maintenance > 118
12.Insert the left end of the cartridge into th e top of the image drum unit first, pushing 
it against the spring on the  drum unit, then lower the right end of the cartridge down 
onto the image drum unit.
13. Pressing gently down on the cartridge to en sure that it is firmly seated, push the 
colored lever (1) towards the rear of the MFP.  This will lock the cartridge into place 
and release toner into the image drum unit.
14. Close the top cover and press down firm ly so that the...

Maintenance > 119
Image Drum Replacement
The MFP contains four image drums: cyan, magenta, yellow and black.
1. Pull the lever (a) firmly to release the lo ck and then gently raise the scanner (b).
2. Press the cover release (a) and open the top cover (b) fully.
CAUTION!
Static sensitive devices, handle with care.
WARNING!
If the MFP has been powered on, the  fuser will be hot. This area is 
clearly labelled. Do not touch.
b
a
b
a
Downloaded From ManualsPrinter.com Manuals 

Maintenance > 120
3.Note the positions of the four cartridges. It  is essential that they go back in the same 
order.
5. Holding it by its top centre, lift the image drum, complete with its toner cartridge, up 
and out of the MFP.
6. Put the cartridge down gently onto a piec e of paper to prevent toner from marking 
your furniture and to avoid damaging the green drum surface.
7. With the colored toner release lever (1) to  the right, pull the lever towards you. This 
will release the bond between the...