OKI C7350DTN User Manual

C7350/7550 User’s Guide: Windows Me/98/95 Operation  •  381
5.Click the New button. C93_Me_PS_Overlay2.bmp  
6.In the Overlay Name list, enter the file name of the overlay. 
Select the pages where you want the overlay to print.
 
NOTE
The Overlay Name must be EXACTLY the same as the file 
name you noted in the previous section. This is the name 
under which the file is stored on the printers’ hard disk 
drive. It is case sensitive.
Downloaded From ManualsPrinter.com Manuals 

C7350/7550 User’s Guide: Windows Me/98/95 Operation  •  382
7.Under Form setting, in the drop-down list, enter or select a 
form name. Click Add.
  C93_Me_PS_Overlay3.bmp  
  
8.Click OK.
9.To continue to add files to the overlay (if required), repeat steps 
5 through 8.
NOTE
The Form Name is a random name of your selection.
Downloaded From ManualsPrinter.com Manuals 

C7350/7550 User’s Guide: Windows Me/98/95 Operation  •  383
10.Under Defined Overlay, highlight the overlay name(s).  
Click Add to add the overlay(s) to the list under Active Overlay.
To select more than one overlay, hold the CTRL key while 
clicking on each name.
 C93_Me_PS_Overlay4.bmp  
11.At the top of the dialog box, use the drop-down list to select 
Use Overlay. Click OK.
12.Click OK to close the Properties dialog box.
Downloaded From ManualsPrinter.com Manuals 

C7350/7550 User’s Guide: Windows Me/98/95 Operation  •  384
Defining Overlays
PCL  
1.Click Start → Settings → Printers.
2.Highlight the printer name.  Click File.  Click Properties..
3.Click the Job Options tab.
4.Click the Overlay... button.
  pcl job options overlay.bmp  
Downloaded From ManualsPrinter.com Manuals 

C7350/7550 User’s Guide: Windows Me/98/95 Operation  •  385
5.To define an overlay, click the Define Overlays button. C73_Me_PCL_Overlay1.bmp  
6.In the Overlay Name list, enter the file name of the overlay 
  
7.In ID Values, enter the ID of the file. Please refer to the 
instructions for the Storage Device Manager utility.
8.Select which pages the overlay is to be printed on from Print 
on Pages or use Custom Pages to select specific page 
numbers in the document. Click Add.
9.Click Close.
10.Under...

C7350/7550 User’s Guide: Windows Me/98/95 Operation  •  386
11.Select Print Using Active Overlays. C73_Me_PCL_Overlay2.bmp 
12.Click OK.
13.Click OK to Close the Properties dialog box.
Downloaded From ManualsPrinter.com Manuals 

C7350/7550 User’s Guide: Windows Me/98/95 Operation  •  387
Printing Posters
PCL Only  
This option allows you to configure and print posters by breaking 
up the document page into multiple pieces.  Each piece prints, 
enlarged, on a separate sheet. Then, the separate sheets are 
combined to produce a poster. It is only available with the PCL 
printer driver.
1.Open the file in your application.  Select File → Print.
2.In the Print dialog box, click the appropriate PCL driver.
3.Click Properties (or...

C7350/7550 User’s Guide: Windows Me/98/95 Operation  •  388
5.Click Options... and enter the configuration details. C93_Me_PCL_Poster2.bmp 
6.Click OK twice.
7.Click OK. Print the document.
Downloaded From ManualsPrinter.com Manuals 

C7350/7550 User’s Guide: Windows NT Printer Drivers  •  389
Windows NT
Printer Drivers
See your printed Software Installation Guide for information on 
installing printer drivers.
You can also go to http://my.okidata.com to view and/or 
download a copy of the Software Installation Guide or for the latest 
information on drivers for your printer.
Which Printer Driver to Use?  
Your printer comes with Windows drivers for PCL and Adobe® 
PostScript® (PS). You can install either of these, or both if you...

C7350/7550 User’s Guide: Windows NT Printer Drivers  •  390
Memory: Enabling
PostScript Only 
Certain options such as additional memory, the duplexer, or 
additional trays may be installed in your printer.
Before using the printer, you must enter the printer driver(s) and 
enable the options. You only need to do this once.
If you have additional memory in your printer, use these 
instructions to update the Windows PostScript driver so that it 
recognizes the additional memory:
1.Click Start → Settings →...