Oce ColorWave 300 User Manual

How to enable and use the 'Top Delivery Tray'
Enable the 'Top Delivery Tray':
After
 the installation of the 'Top Delivery Tray'you must enable the 'Top Delivery Tray'
in 
the Océ Express WebTools.
Select
 'Preferences'/ 'System settings'/ 'Printer properties'/ 'Top Delivery Tray' 
and set
it
 to 
'Present'.
Use 
the 'Top Delivery Tray'in the Océ Express WebTools:
■ For
 a Print Job: 
Select 'Preferences'/ 'System...

The printing system consumables
#
Description
Consumable part
Consumable
Roll that carries the
media. A roll has a 2"
core.
roll
media
For

 detailed informa-
tion:
  ‘Preferred Océ me-
dia names’  on page 345
The 
core of the media
roll
 is the cardboard in-
ner part 
of the roll.
core
Optional
 
adapter to
load a media roll with a
3" core.
adapter

 
for 3" core
Knife to cut the media.
media cutter
printhead
Océ

 
ColorWave 300
supplies Container
 that contains
a bag 
with ink.
ink tank...

Chapter 3
Quick 
start
Downloaded From ManualsPrinter.com Manuals 

Connect the mains supply cableCaution:
Make sure the power switch is in 'off' position.
1.
Plug 
in the mains supply cable at the power connection at the back of the printer. 2. Plug 
the other side of the mains supply cable into the wall socket.
Chapter 3
 - Quick start44Connect the mains supply cable
Downloaded From ManualsPrinter.com Manuals              

Switch on the printing system
1.Switch on the power switch at the rear side of the printing system. 2.
Use 
the on / off button at the front side of the printer to switch on the printing system. Chapter 3
 - Quick start 45Switch on the printing system
Downloaded From ManualsPrinter.com Manuals                            

Replace / Install the media
Introduction
The standard configuration of the Océ ColorWave 300 contains two rolls of media .
Appendix
 A contains a list of the supported media types 
and media sizes.
This
 
section describes how to remove and load a roll of media .
When
 to do Change a roll when 
a job needs a media type or size that is not on one of the rolls.
Change
 the media type that 
is defined on the system when the defined media type and
the
 available media type do not 
correspond.
How to remove a...

2.
Use both hands to remove the roll. [24]
 Remove the roll
3. Both far ends of the roll contain roll holders with handles. Lift the handles to release the
roll holders. [25]
 Release the roll holders
Chapter 3
 - Quick start 47Replace / Install the media
Downloaded From ManualsPrinter.com Manuals     

4.
Remove the roll holders. [26] Remove the roll holders
How to load a new media roll 1.Insert

 the roll holder in 
both ends of the new media roll.
2. Press the handles down to 
fasten the roll holders.
Chapter 3
 - Quick start48Replace / Install the media
Downloaded From ManualsPrinter.com Manuals   

3.
Put the saddles into position at the ends of the track. [27]
 Saddles
4. Use 
both hands to place both roll holders in the green saddles on the printer.
5. Use
 
both hands to slide the medium under the paper guide. Place the media on the
printer
 as 
shown in the figure below. The 
medium loads into the printer from the top of the media roll.
Make sure 
the medium makes contact with the paper guide.
Chapter 3
 - Quick start 49Replace / Install the media
Downloaded From ManualsPrinter.com Manuals     

6.
The printer automatically draws the medium into the correct position.
7. The
 
user panel displays the message 'New media detected on roll 1' or 'New media de-
tected
 on roll 2'. 
Follow the steps in the wizard to define the correct media type. The
media
 size 
is detected automatically.
Note:
The printer automatically detects the width of the media. Chapter 3
 - Quick start50Replace / Install the media
Downloaded From ManualsPrinter.com Manuals