Oce ColorWave 300 User Manual

Extended copy jobs
Introduction to copy jobs
A basic copy job only takes two steps. Feed the original face up and press the start button.
Every other type of copy job is called an extended copy job.
An
 extended copy job takes some additional steps, where you select a specific copy template
and, if 
necessary, change the predefined copy job settings on the user panel. The copy
templates are 
defined in the Océ Express WebTools (see ‘Define the copy job preferences
and copy templates’  on page 127 ). When...

Do an extended copy job
1.Feed the original face up and centered on the original feeding table.
Note:
You do not need to center the original precisely. The exact position of the original is au-
tomatically detected by the scanner. The 
'Copy' tab is automatically activated on the user panel.
2.
Open the 'Copy' tab 
with the confirmation button above the scroll wheel.
3. Select your 
copy template.
Chapter 5
 - Use the Océ ColorWave 300 multifunction printer182Do an extended copy job...

If you want to change the pre-defined settings of the selected copy template, use the
confirmation button to open the copy template and display an overview of the pre-defined
settings groups. 4.
Scroll 
to the settings group you want to change. 5.
■
Open the settings group you want to change with the confirmation button and scroll
to 
the setting you want to change.
■ Open this setting, scroll through the settings values 
and select the correct value with
the
 confirmation 
button.
■ Change the other...

Available settings for copy jobs
Introduction
The Océ ColorWave 300 provides a lot of settings to manage all your different copy jobs.
These
 settings are used for extended copy jobs. The following table gives an overview and
a very 
short description of the available settings. You can find a detailed description of
each
 
setting in the Océ Express WebTools.
Settings
 group: 'Print mode' #
Function
Settings values
Setting
Define the type of original.
'Color'
'Grayscale'...

Function
Settings values
Setting
Reduce the background noise of the im-
age. 'On'
'Off'
'Auto'
'Backgnd
comp'
The width of the original is automatically
detected by the scanner.'Auto'
'Width detect'
'A0'
'A1'
'A2'
'A3'
'A4'
'A5'
'E+

 (36")'
'B1

 
(707 mm)'
'B2
 
(19.69 in)'
Scales
 the image to fit the selected media
size.
Note:
Depend on the media series you
defined in 
the Océ...

Function
Settings values
Setting
210 to 914 mm
The width of the original is a custom size. 'Custom'
Settings group: 'Media' #
Function
Settings values
Setting
Define the media feed 
to copy or print
on.
 When you 
select 'Auto' the printer
automatically
 selects the media roll. 'Auto'
'Roll 1' (description of
media type and media
size

 
loaded on roll 1)
'Roll
 
2' (description of
media type and media
size

 
loaded on roll 2)
'Roll
 selection'...

Function
Settings values
Setting
Scales the image to a custom percentage.10 - 1000 '%'
'Custom'
Settings group: 'Delivery' #
Function
Settings values
Setting
The 
location to deposit the sheet.
Note:
Not all media types can be deliv-
ered 
to the 'Top Delivery Tray'.'Lower tray'
'Top

 Delivery Tray'
'Output'
Settings

 group: 'Sheet size' #
Function
Settings values
Setting
'Determines the cut 
size of the print.
'Standard':
 the...

Function
Settings values
Setting
Adds a blank strip at the beginning of the
output.0 to 400 mm
'Top'
Adds 
a blank strip at the bottom of the
output. 0 to 400 mm
'Bottom'
Settings group: 'Positioning' #
Function
Settings values
Setting
'Aligns 
the image on the media.''Top left'
'Top'
'Top
 right'
'Left'
'Center'
'Right'
'Bottom

 left'
'Bottom'
'Bottom

 right'
'Alignment'
'Shifts
 the...

Function
Settings values
Setting
'Shifts the image in the vertical direction
(after alignment to one of positions given
in 'Alignment').'- 1219
 mm to + 1219
mm
'Shift vertical'
Settings group: 'Erase margins' #
Function
Settings values
Setting
'Erase 
a strip from the beginning of the
original.' 0 to 400 mm
'Top'
'Erase 
a strip from the bottom of the
original.' 0 to 400 mm
'Bottom'
'Erase 
a strip from the left side of the...

Function
Settings values
Setting
'Erase a strip from the right side of the
original.' 0 to 400 mm
'Right'
Settings group: 'Erase area' #
Function
Settings values
Setting
'The horizontal offset where the erase area
starts.'0
 to 914 mm
'Hor offset'
'The 
vertical offset where the erase area
starts.' 0 to 6000 mm
'Vert offset'
'The 
width of the area to erase.'0 to 914 mm
'Width'
'The 
length of the area to erase.'0 to 6000...