Home > Nortel > Communications System > Nortel Modular Ics 6.0 System Coordinator Guide

Nortel Modular Ics 6.0 System Coordinator Guide

Here you can view all the pages of manual Nortel Modular Ics 6.0 System Coordinator Guide. The Nortel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 251

P0992640 03 Modular ICS 6.0 System Coordinator Guide
Glossary
A
access code: Different sequences of 
characters used to gain access to these 
Norstar features: Line pools, Call park, 
external lines, Direct-Dial telephone, 
Auto DN, and DISA DN.
alarm code: A number that appears 
on the alarm telephone display, 
informing you that the  ICS has detected 
a fault in the system.
alarm telephone: A telephone that is 
designated to receive reports of Norstar 
system problems. This function is 
usually...

Page 252

252 / Glossary
Modular ICS 6.0 System Coordinator Guide P0992640 03
Automatic Daylight Savings 
Time: A feature that switches the 
system to standard or daylight savings 
time at pre-programmed times. It is 
turned on or off under 
Daylight time 
in Sys prgrmmng.
Automatic Telephone 
Relocation:  A feature that allows a 
telephone to retain personal and system 
programming when the telephone is 
plugged into a different Norstar modular 
jack. 
Automatic Telephone 
Relocation
 is enabled under Set...

Page 253

Glossary / 253
P0992640 03 Modular ICS 6.0 System Coordinator Guide
specific number of rings. Call Forward 
No Answer
 is assigned under Capabilities in Terminals&Sets 
programming.
Call Forward On Busy: A feature 
that forwards all calls at your telephone 
to another designated telephone if your 
telephone is busy. This feature is 
assigned under 
Capabilities in 
Terminals&Sets programming.
Call Forward Override: An 
automatic system feature that allows 
you to call someone and ask them to 
stop...

Page 254

254 / Glossary
Modular ICS 6.0 System Coordinator Guide P0992640 03
calls. Note: Systems which use a 
centralized voice mail system attached 
to a Meridian 1,  can provide this  service 
to all nodes of the network.
Camp timeout: The length of a delay 
before a camped call is returned to the 
telephone that camped the call. The 
length of delay is set under 
Feature 
settings
 in Sys prgrmmng.
Central answering position
 
(CAP): An M7324 telephone that has 
been designated as a CAP under CAP 
assignment...

Page 255

Glossary / 255
P0992640 03 Modular ICS 6.0 System Coordinator Guide
D
data terminal: A device, such as a 
modem, that can be used to  transfer data 
instead of sound over a telephone 
network. You cannot use Norstar 
programming to set up such devices. 
See the documentation that 
accompanies the device.
date: See Show Time or Time and 
Date.
defaults: The settings for all Norstar 
features when the system is first 
installed. Settings are changed from 
their defaults in programming. In this 
manual,...

Page 256

256 / Glossary
Modular ICS 6.0 System Coordinator Guide P0992640 03
password. Once the password is 
accepted, the caller hears system dial 
tone and can use Remote Access 
features. See Remote Access.
Disconnect Supervision: A setting 
that enables the Norstar system to detect 
if an external caller hangs up. Once an 
external caller hangs up, the Norstar 
system can disconnect its line. 
Disconnect Supervision is enabled 
under Trunk/Line data in Lines 
programming.
display: A liquid crystal display...

Page 257

Glossary / 257
P0992640 03 Modular ICS 6.0 System Coordinator Guide
external paging: A feature you can 
use to make voice announcements over 
an externally-mounted loudspeaker 
connected to the ICS. The external 
speaker is not a Norstar component and 
must be supplied by the customer.
F
feature button: Many Norstar 
features are invoked by pressing the 
Feature (
²) button followed by a 
feature code. The feature button is also 
used to exit a feature.
feature code: A number that is used 
to activate a...

Page 258

258 / Glossary
Modular ICS 6.0 System Coordinator Guide P0992640 03
Host system signaling: (Also 
referred to as end-to-end signaling.) 
System telephones can access a remote 
system or dial a number on an alternate 
carrier by means of host feature 
activation, such as Link, Pause and Run/
Stop.
Hospitality The Hospitality features 
allow business which use hospitality 
telephones, or room-based telephones, 
to control access, alarms, and 
maintenance duties through the 
telephones.
Hotline: This...

Page 259

Glossary / 259
P0992640 03 Modular ICS 6.0 System Coordinator Guide
L
Last Number Redial: ²Þ
A feature that allows you to redial the 
last external number you dialed.
Fixed line: 
A telecommunications line between two 
service points leased from a 
communications carrier for private use, 
usually incurring a monthly service rate. 
Fixed  lines  setting is  used  solely by data 
modules.
Least cost routing: See Routing 
service.
line: The complete path of a voice or 
data connection between one telephone...

Page 260

260 / Glossary
Modular ICS 6.0 System Coordinator Guide P0992640 03
indicators. An M7310 can be equipped 
with a Busy Lamp Field.
M7324 telephone:  A telephone with 
a two-line display, three display buttons, 
and 24 programmable memory buttons 
with indicators. An M7324 telephone 
can be equipped with a CAP m odule.
Malicious Caller ID (MCID)   This 
feature is a European ETSI-based 
network feature that allows  a user to use 
² ¡áà record the caller 
information at the service provider.
memory buttons:...
Start reading Nortel Modular Ics 6.0 System Coordinator Guide

Related Manuals for Nortel Modular Ics 6.0 System Coordinator Guide

All Nortel manuals