Nitsuko Portrait 308/824 Program Record Form Manual

							Program 13  - Extension Options (3)(Display  shows:  STN ASSIGNMENT3)
Extension
Port #(A.)
Confirm.
Tone(B.) Do Not
Disturb(C.) Alarm
Audible(D.) Voice
Announce
Device Port(E.)      
Terminal
Connection
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Options
(A.) Confirmation Tone
0=enabled, 1=disabled
(B.) Do Not Disturb
0=disabled, 1=incoming CO
calls blocked, 2=CO and
ICM calls blocked, 3=CO
and ICM calls blocked or
CO calls blocked and ICM
calls allowed
(C.) Alarm Audible
0=disabled, 1=enabled
(D.) Voice Announce Device Port
0=disabled, 1=enabled
(E.) Terminal Connection
0=not connected,
1=connected
Program Record Form Entry
1.  Enter the desired option
     number in for each feature.
System Program Entry
1.  Enter 13 (program
     number).
2.  Press *.
3.  Enter extension port
     number.
4.  Press *.
5.  Enter data from
     columns A-E.
6.  Press *.
7.  The next extension
     port displays. Repeat
     steps 5-6 OR
     Press * to advance
     to another extension
     port OR
     Press # to exit
     program.
- 13 - 
						

							Program 14 - Flexible Station Numbering(Display  shows:  FLEX.STA.#ING)
Extension
Port #(A.)
Extension
Number
Assigned to
Port(B.) Number
Plan
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Options
(A.) Extension Number Port Assignment
10-79 = 2-digit number plan extensions,
110-799 = 3-digit number plan extensions
(B.) Number Plan
002 = 2-digit number plan assignment,
003 = 3-digit number plan assignment
Program Record Form Entry
1.  Enter the extension numbers to
     be assigned to each port, and
     assign the number plan.
System Program Entry
To change port assignments:
1.  Enter 14 (program number).
2.  Press * *.
3.  Enter the data from column B.
4.  Press *.
5.  Press # to exit program.
1.  Enter 14 (program number).
2.  Press *.
3.  Enter data from column A.
4.  Press *.
5.  Enter the next extension port number
     to be assigned by repeating steps 5-6 OR
     Press * to skip the displayed port OR
     Press # to exit program.
To change the system numbering plan:
- 14 - 
						

							Program 15  - System Options (1)(Display  shows:  SYS ASSIGNMENT1)
(A.) Flexible
Line
Appearance(B.) Night
Transfer(C.)
Automatic
Line Access(D.)
Exclusive
Hold(E.) Single
Step Access
Program Record Form Entry
1.  Enter desired option number in each
     features column.
System Program Entry
1.  Enter 15 (program number).
2.  Press *.
3.  Enter the data from columns A-E.
4.  Press *.
5.  Press # to exit the program.
Program 16  - System Options (2)(Display  shows:  SYS ASSIGNMENT2)
(A.) Ringing
Line
Preference(B.)
Recalling
Line
Preference(C.) Allow
SLT to
Access Line
on Hold(D.)
Add-On
Conference
Setup Mode(E.)
Multi-Line
Conference
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 16 (program number).
2.  Press *.
3.  Enter the data from columns A-E.
4.  Press *.
5.  Press # to exit the program.
Options
(A.) Flexible Line Appearance
0=disabled, 1=enabled
(B.) Night Transfer
0=all tenants, 1=each tenant
(C.) Automatic Line Access
0=disabled, 1=press SPK key and
queuing group number, 2=dial 0 from
on-hook condition, 3=press SPK key
and queuing group number and dial 0
from on-hook condition
(D.) Exclusive Hold
0=disabled, 1=enabled
(E.) Single Step Access
0=disabled, 1=enabled
Options
(A.) Ringing Line Preference
0=disabled, 1=all incoming calls to Group
1 and ringing incoming calls to Group 2,
2=incoming ringing calls to Group 1 and
Group 2
(B.) Recalling Line Preference
0=disabled, 1=enabled
(C.) Allow SLT to Access Line on Hold
0=no access for line on hold, 1=can
access line on hold
(D.) Add-On Conference Setup Mode
0=increase one by one, 1=increase 5
parties at once
(E.) Multi=Line Conference
0=disabled, 1=enabled
- 15 - 
						

							Program 17  - System Options (3)(Display  shows:  SYS ASSIGNMENT3)
(A.) Dial
Pulse
Sender
Speed(B.)
Make/Break
Ratio(C.) DTMF
Duration(D.) Storage
Quantity of
Speed Dial(E.)
Existence of
Attendant
for DISA
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 17 (program number).
2.  Press *.
3.  Enter the data from columns A-E.
4.  Press *.
5.  Press # to exit the program.
Program 18  - System Options (4)(Display  shows:  SYS ASSIGNMENT4)
(A.) Three
Minute
Warning
Tone(B.) Not
Used(C.) Speed
Dialing
Restriction(D.)
Handset
Receiver
Volume(E.) Time
Indication
0
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 18 (program number).
2.  Press *.
3.  Enter the data from columns A-E.
4.  Press *.
5.  Press # to exit the program.
Options
(A.) Dial Pulse Sender Speed
0=10 PPS, 1=20 PPS
(B.) Make/Break Ratio
0=33%, 1=39%
(C.) DTMF Duration
0=high speed (80 ms On - 80 ms Off),
1=mid speed (100 ms On - 100 ms Off),
2=low speed (150 ms On - 150 ms Off)
(D.) Storage Quantity of Speed Dial
0=100 (numbers range from 00-99), 1=200
(numbers range from 000-199)
(E.)  Existence of Attendant for DISA
0=none, 1=day mode, 2=night mode,
3=day and night mode
Options
(A.) Three Minute Warning Tone
0=disabled, 1=enabled
(B.) Not Used
Must be set to 0
(C.) Speed Dialing Restriction
0=not restricted, 1=restricted
(D.) Handset Receiver Volume
0=reset after conversation, 1=keep
current volume
(E.) Time Indication
0=12 hour mode, 1=24 hour mode
- 16 - 
						

							Program 19  - System Options (5)(Display  shows:  SYS ASSIGNMENT5)
(A.) All Call
to External
Zone   (B.)  
Intercom
Signaling(C.)
Microphone
On/Off(D.) Room
Monitor(E.) Not
Used
0
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 19 (program number).
2.  Press *.
3.  Enter the data from columns A-E.
4.  Press *.
5.  Press # to exit the program.
Program 20  - System Options (6)(Display  shows:  SYS ASSIGNMENT6)
(A.) Door
Chime Tone
Duration(B.) Paging
Splash Tone(C.) Door
Alert Tone(D.)
Automatic
Line Access
Code for
SLT(E.)
Existence of
Door Box
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 20 (program number).
2.  Press *.
3.  Enter the data from columns A-E.
4.  Press *.
5.  Press # to exit the program.
Options
(A.) All Call to External Zone
0=disabled, 1=speaker 1,
2=speaker 2, 3=speaker 1 and 2
(Option 2 and 3 not used in
Portrait 308)
(B.) Intercom Signaling
0=voice call, 1=forced ring signal
(C.) Microphone On/Off
0=on, 1=off
(D.) Room Monitor
0=disabled, 1=enabled
(E.) Not Used
Must be set to 0
Options
(A.) Door Chime Tone Duration
0=2 times, 1=30 seconds
(B.) Paging Splash Tone
0=disabled, 1=enabled
(C.) Door Alert Tone
0=disabled, 1=enabled
(D.) Automatic Line Access Code
for SLT
0=off-hook and dial 0, 1=off-
hook and dial 9
(E.) Door Box
0=none, 1=Door Box 1 enabled,
2=Door Box 2 enabled, 3=Door
Box 1 and 2 enabled
- 17 - 
						

							Program 21  - Exclusive Hold Timers(Display  shows:  EXC.HOLD TIMERS)
(1.) Recall
Start Time(2.) Recall
Signal
Duration
Time
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 21 (program number).
2.  Press *.
3.  Enter the option number to be programmed (1 or 2).
4.  Press *.
5.  Enter the value for the option being programmed.
6.  Press *.
7.  If the first option number entered was 1, you can enter the value for option number 2 OR
     Press # to exit the program.
Program 22  - System Hold Timers(Display  shows:  SYS.HOLD TIMERS)
(1.) Recall
Timer(2.)
Duration
Timer
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 22 (program number).
2.  Press *.
3.  Enter the option number to be programmed (1 or 2).
4.  Press *.
5.  Enter the value for the option being programmed.
6.  Press *.
7.  If the first option number entered was 1, you can enter the value for option number 2 OR
     Press # to exit the program.
Options
(1.) Recall Start Time
000=not assigned, 001-225 =
10-2550 seconds
(2.) Recall Signal Duration Time
000=not assigned, 001-225 =
1-255 seconds
Options
(1.) Recall Timer
000=not assigned, 001-225 =
10-2550 seconds
(2.) Duration Timer
000=not assigned, 001-225 =
1-255 seconds
- 18 - 
						

							Program 23 - Unscreened Transfer Recall(Display  shows:  UNANN.XFER TIMER)
Unscreened
Transfer
Recall
Timer
Program Record Form Entry
1.  Enter desired value for the timer.
System Program Entry
1.  Enter 23 (program number).
2.  Press *.
3.  Enter the value for the timer.
4.  Press *.
5.  Press # to exit the program.
Program 24  - Screened Transfer Recall(Display  shows:  ANND XFER TIMER)
Screened
Transfer
Timer
Program Record Form Entry
1.  Enter desired value for the timer.
System Program Entry
1.  Enter 24 (program number).
2.  Press *.
3.  Enter the value for the timer.
4.  Press *.
5.  Press # to exit the program.
Options
Unscreened Transfer Recall Timer
000=disabled, 001 - 255 = 10-2550
seconds
Options
Screened Transfer Recall Timer
000=disabled, 001 - 255 =
10-2550 seconds
- 19 - 
						

							Program 25 - Call Duration Timer(Display  shows:  CALL DUR. START)
 Call
Duration
Timer
Program Record Form Entry
1.  Enter desired value for the timer.
System Program Entry
1.  Enter 25 (program number).
2.  Press *.
3.  Enter the value for the timer.
4.  Press *.
5.  Press # to exit the program.
Program 26 - Flash Timer(Display  shows:  FLASH TIMER)
(1.) CO Line
Flash Timer(2.) PBX/
Centrex
Line Flas h
Timer
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 26 (program number).
2.  Press *.
3.  Enter the option number to be programmed.
4.  Press *.
5.  Enter the value for the option being programmed.
6.  Press *.
7.  If the first option number entered was 1, you can enter the value for option number 2 OR
     Press # to exit the program.
Options
Call Duration Timer
000=disabled, 001 - 180 = 1-180 seconds
Options
(1.) CO Line Flash Timer
000 = not assigned, 001 - 250 =
10 - 2500 ms
(2.) PBX/Centrex Line Flash Timer
000 = not assigned, 001 - 250 =
10 - 2500 ms
- 20 - 
						

							Program 27 - SMDR Timer(Display  shows:  SMDR TIMERS)
(1.) Call
Duration
Timer(2.) Call
Start Timer
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 27 (program number).
2.  Press *.
3.  Enter the value for the Call Duration Timer.
4.  Press *.
5.  Enter the value for the Call Start Timer.
6.  Press *.
7.  Press # to exit the program.
Program 28 - Call Forward Transfer Timer(Display  shows:  DELAY RING TIMER)
Call
Forward
Transfer
Timer
Program Record Form Entry
1.  Enter desired value for the timer.
System Program Entry
1.  Enter 28 (program number).
2.  Press *.
3.  Enter the value for the timer.
4.  Press *.
5.  Press # to exit the program.
Options
(1.)  Call Duration Timer
00 = starts immediately,
01 - 60 = 1 - 60 seconds
(2.) Call Start Timer
00=starts immediately,
01 - 60 = 1 - 60 seconds
Options
Delay Ring Transfer Timer
000=disabled, 001 - 255 = 1-255 seconds
- 21 - 
						

							Program 29 - Attendant Reverting(Display  shows:  ATT.REVERT TIMER)
Attendant 
Revert 
Timer
Program Record Form Entry
1.  Enter desired value for the timer.
System Program Entry
1.  Enter 29 (program number).
2.  Press *.
3.  Enter the value for the timer.
4.  Press *.
5.  Press # to exit the program.
Program 30 - Voice Message Timer(Display  shows:  ANN.TIMERS)
(1.)
Automatic 
Answering
Timer(2.) Dial
Tone Sent
Timer
Program Record Form Entry
1.  Enter desired option number in each features column.
System Program Entry
1.  Enter 30 (program number).
2.  Press *.
3.  Enter the option number (1 or 2) for the timer to be programmed.
4.  Press *.
5.  Enter the value for the timer being programmed.
6.  Press *.
7.  If the first option number entered was 1, you can enter the value for option number 2 OR
     Press # to exit the program.
Options
Attendant Revert Timer
000=disabled, 001 - 255 = 1-255 seconds
Options
(1.) Automatic Answering Timer
000=disabled, 001 - 255 = 1 - 255
seconds
(2.) Dial Tone Sent Timer
000=disabled, 001 - 255 = 1 - 255
seconds
- 22 -