Nitsuko Portrait 308/824 Program Record Form Manual

							Program 3 - Line Options (2)(Display shows:  LINE ASSIGNMENT2)
Line #(A.) DISA
Line(B.) DISA
Access
Mode(C.)
Common
Line U s e(D.) Non-
Restricted
Line(E.) Caller
ID
01
02
03
04
05
06
07
08
Program Record Form EntryOptions
1.  Enter desired option number in each(A.) DISA Line
     features column.0=disabled, 1=enabled
System Program Entry(B.) DISA Line Access Mode
1.  Enter 03 (program number).0=no access, 1=day mode, 2=night mode,
2.  Press *.3=day and night mode
3.  Enter line number.
4.  Press *.(C.) Common Line Use
5.  Enter data from columns A-E.0=cannot use as a common line,
6.  Press *.1=can use as a common line
7.  Next line number displays.  Repeat steps 5-6 OR
     Press * to advance to another line OR(D.) Non-Restricted Line
     Press # to exit program.0=restricted, 1=non-restricted
(E.) Caller ID
0=disabled, 1=enabled
- 3 - 
						

							Program 4 - Extension Options (1)(Display shows:  STN ASSIGNMENT1)
Extension
Port #(A.)
Executive
Override(B.) CO
Off-Hook
Signaling(C.)
Intercom
Off-Hook
Signaling(D.)
Intercom
Signal Call(E.) Headset
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Options
(A.) Executive Override
0=not allowed, 1=allowed
with tone, 2=allowed
without tone
(B.) CO Off-Hook Signaling
0=disabled, 1=enabled
(C.) Intercom Off-Hook Signaling
0=disabled, 1=manually
sent when busy, 2=automatically sent
when busy
(D.) Intercom Signaling
0=voice call, 1=forced ringing
(E.) Headset
0=disabled, 1=enabled
Program Record Form Entry
1.  Enter desired option number
     in each features column.
System Program Entry
1.  Enter 04 (program
     number).
2.  Press *.
3.  Enter extension port
     number.
4.  Press *.
5.  Enter data from
     columns A-E.
6.  Press *.
7.  Next extension port
     displays. Repeat steps
     5-6 OR
     Press * to advance to
     another extension
     port OR
     Press # to exit program.
- 4 - 
						

							Program 5 - Unsupervised Conference Port(Display shows:  UNSUP.CONF.PORT)
Circuit
NumberExtension
Port #
01
02
03
04
Program Record Form Entry
1.  Enter desired extension port for each Unsupervised
     Conference circuit.
1.  Enter 05 (program number).
2.  Press *.
3.  Enter extension port number to be assigned to the
     first Unsupervised Conference circuit.
4.  Press *.
5.  Enter the extension port to be assigned to the next
     circuit number OR
     Press * to advance to another circuit number OR
     Press # to exit program.
System Program Entry
- 5 - 
						

							Program 6 - Outgoing Line Access(Display shows:  OUTGOING CO ACC.)
Extension
Port #(A.) Line
Group #1(B.) Line
Group #2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Options
(A.) Outgoing Line Group #1
00=no group assigned, 01-30=groups 1-30
(B.) Outgoing Line Group #2
00=no group assigned, 01-30=groups 1-30
Program Record Form Entry
1.  Enter the outgoing line group numbers
     (1 and 2) to be assigned to each
     extension.
System Program Entry
1.  Enter 06 (program number).
2.  Press *.
3.  Enter extension port number.
4.  Press *.
5.  Enter data from column A.
6.  Press *.
7.  Enter data from column B.
8.  Press *.
9.  Next extension port displays.
     Repeat steps 5-8 OR
     Press ** to advance to another
     extension port OR
     Press # to exit program.
- 6 - 
						

							Program 7 - Incoming Line Access/Audible(Display shows:  INC.LINE ACC/AUD)
Extension
Port #(A.) Line
Group #1(B.) Ring
Type for
Line Group
#1(C.) Line
Group #2(D.) Ring
Type for
Line Group
#2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Options
(A.) Incoming Line Group #1
Enter first line group number [00=no
group assigned, 01-30=groups 1-30]
(B.) Ring Type for Line Group #1
0=no ringing, 1=day ringing, 2=night ringing,
3=day and night ringing
(C.) Incoming Line Group #2
Enter second line group number
[00=no group assigned, 01-30=groups
1-30]
(D.) Ring Type for Line Group #2
0=no ringing, 1=day ringing, 2=night ringing,
3=day and night ringing
Program Record Form Entry
1.  For each extension, enter the
     incoming line group numbers
     (1 and 2) and the ring types to
     be assigned to them.
System Program Entry
1.  Enter 07 (program number).
2.  Press *.
3.  Enter extension port number.
4.  Press *.
5.  Enter data from columns A-B.
6.  Press *.
7.  Enter data from columns C-D.
8.  Press *.
9.  Next extension port displays.
     Repeat steps 5-8 OR
     Press ** to advance to another
     extension port OR
     Press # to exit program.
- 7 - 
						

							Program 8 - Extension Options (2)(Display  shows:  STN ASSIGNMENT2)
Extension
Port #(A.)
Instrument
Type(B.) SLT
Dial Plan(C.) Internal
Page Zone(D.) Tenant
Group(E.) Park
Group
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Program Record Form Entry
1.  Enter the desired
     option number in each
     features column.
System Program Entry
1.  Enter 08 (program
     number).
2.  Press *.
3.  Enter extension port
     number to be
     programmed.
4.  Press *.
5.  Enter data from
     columns A-E.
6.  Press *.
7.  The next extension
     port displays.
     Repeat steps 5-6 OR
     Press * to advance to
     another extension port
     OR
     Press # to exit
     program.
Options
(A.) Instrument Type
0=KTS, 1=DISA, 2=SLT
(DP), 3=SLT (DTMF)
(B.) SLT Dial Plan Set
0=Dial Plan 1, 1=Dial Plan 2
(C.) Internal Page Zone
0=disabled, 1=Page Zone 1,
2=Page Zone 2, 3=Page
Zone 3, 4=Page Zone 4
(D.) Tenant Group
0=disabled, 1=Tenant
Group 1, 2=Tenant Group 2,
3=Tenant Group 3,
4=Tenant Group 4
(E.) Park Group
0=disabled, 1=Park Group
1, 2=Park Group 2, 3=Park
Group 3, 4=Park Group 4
- 8 - 
						

							Program 9 - Executive Call Forward(Display  shows:  EXEC. CALL FWD)
Executive 
Call
Forward
Pair(A.)
Executive
Extension
Port #(B.)
Secretary
Extension
Port #
1
2
3
4
5
6
7
8
Program Record Form Entry
1.  Enter the extensions for the executive and secretary pairs.
System Program Entry
1.  Enter 09 (program number).
2.  Press *.
3.  Enter the data from column A.
4.  Press *.
5.  Enter data from column B.
6.  Press *.
7.  Next Call Forwarding Pair number displays.  Repeat steps 3-6 OR
     Press * to advance to another Call Forwarding Pair OR
     Press # to exit program.
Options
(A.) Executive Extension Port #
00=none, 10-system maximum= extension
port number
(B.) Secretary Extension Port #
00=none, 10-system maximum= extension
port number
- 9 - 
						

							Program 10 - Dual Handsfree Hotline(Display  shows:  DUAL HF HOTLINE)
Dual HF
Hotline Pair(A.)
Secretary
Extension
Port #(B.) 
Executive 
#1   
Extension
Port # (C.)
Executive 
#2  
Extension
Port #
1
2
3
4
Program Record Form Entry
1.  Enter the extensions for the executive and secretary pairs.
System Program Entry
1.  Enter 10 (program number).
2.  Press *.
3.  Enter the data from column A.
4.  Press *.
5.  Enter data from column B.
6.  Press *.
7.  Enter data from column C.
8.  Press *.
9.  Enter next Dual Handsfree Hotline pair by repeating steps 3-8 OR
     Press # to exit program.
Options
(A.) Secretary Extension Port #
00=none, 10-system maximum=
extension port number
(B.) Executive #1 Extension Port #
00=none, 10-system maximum=
extension port number
(C.) Executive #2 Extension Port #
00=none, 10-system maximum=
extension port number
- 10 - 
						

							Program 11 - Hunt Groups(Display  shows:  HUNT GROUPS)
Ext. # in
Hunt GroupHunt Group
0Hunt Group
1Hunt Group
2Hunt Group
3Hunt Group
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Program Record Form Entry
1.  Enter the extensions to be assigned to each Hunt Group.
System Program Entry
1.  Enter 11 (program number).
2.  Press *.
3.  Enter the Hunt Group number (0-4) to be programmed.
4.  Press *.
5.  Enter the first extension port for that particular Hunt Group.
6.  Press *.
7.  Continue entering extension ports for the Hunt Group as in steps 5-6.
8.  When all extensions are entered, continue pressing * through the 16th extension to continue with the next
     group or press # to exit the program.
9.  Enter next Hunt Group by repeating steps 3-8 OR
     Press # to exit program.
- 11 - 
						

							Program 12 - Door Chime Box(Display  shows:  DOOR CHIME BOX)
Door Box   
#1(A.)
Extension #(B.) Ring
TypeDoor Box  
#2(A.)
Extension #(B.) Ring
Type
11
22
33
44
55
66
77
88
99
10 10
Program Record Form Entry
1.  Enter the required extensions for each Door Box
     and assign the ring type each extension
     should receive.
System Program Entry
1.  Enter 12 (program number).
2.  Press *.
3.  Enter the Door Box number (1 or 2) to be programmed.
4.  Press *.
5.  Enter the first extension port to be assigned and its ring type.
6.  Press *.
7.  Continue entering extension ports and ringing assignments
     through the tenth extension port.
     If no other extensions need to be entered, press * through the
     tenth extension or press # to exit the program.
8.  To enter the next Door Box number repeat steps 3-7 OR
     Press # to exit program.Options
(A.) Extension Port #
00=none, 10-system
maximum=extension port number
(B.) Ring Type
0=no ringing, 1=day ringing,
2=night ringing, 3=day and night ringing
- 12 -