NEC Visualink 128/384 Engineering Guide

NDA-24233 Issue 2Page 3-15
VisuaLink 128/384 Engineering Guide Console Command List
SMTC Sets Audio or Audio/Video Mute Setting 2-13
RMTC Checking Audio or Audio/VideoOutput Mute Setting 2-14
Description: Sets whether the audio or audio and video outgoing is muted or unmuted 
at the start of communication when the VisuaLink automatically answers 
or manual answered calls.
Command Format: SMTC p1 
p1:   A: Audio is set to be Muted (Default)
AV: Video/Audio is set to be Muted
Response: Normal Response:...

Page 3-16NDA-24233 Issue 2
Console Command List VisuaLink 128/384 Engineering Guide
3.3  LINE Setting Command
SNET Setting Network Type (P x 64/56) 3-1
Note:
The command can only be issued when the VisuaLink is not in a call.
RNET Checking Network Type Setting (P x 64/56) 3-2
Description: Sets a network type (P x 64/56).  Some networks use 8 kbps out of the 64 
kbps for network control information, so the network available for users 
may be limited to P x 56 kbps.  When connecting to the network, check...

NDA-24233 Issue 2Page 3-17
VisuaLink 128/384 Engineering Guide Console Command List
NNSS Setting Transmission Line Type 3-3
Note:
High Speed digital basic leased lines are currently only available in Japan.
NNSI Checking Transmission Line Type Setting 3-4
Description: Sets the line interface:  High speed digital basic leased line (128k I 
Interface) or National ISDN-1 Basic Rate Interface
 
Command Format: NNSS  p1 
p1: D2B :  *High speed digital basic leased line 
(128k I Interface)
I2B :  National...

Page 3-18NDA-24233 Issue 2
Console Command List VisuaLink 128/384 Engineering Guide
SLSP Setting Transmission Line Speed 3-5
RLSP Checking Transmission Line Speed Setting 3-6
Note:
The response will always be a 64 kbps increment.  It is recommended that the RNET command be used 
combined with RLSP. Description: Sets transmission speed.
Command Format: SLSP  p1 
p1: B : 56/64 kbps
2B : 2x56/2x64 kbps
3B : 168/192 kbps
4B : 224/256 kbps
5B : 280/320 kbps
6B : 336/384 kbps
Response: Normal Response:  OK...

NDA-24233 Issue 2Page 3-19
VisuaLink 128/384 Engineering Guide Console Command List
3.4  DATA Command
SDM2 Setting LSD Speed 4-1
Description:Setting Low Speed Data (LSD) port speed• Allows for H.281 far-end camera control
• PC-to-PC data transmission
Command Format:SDM2 p1
 
p1: OFF : OFF
1.2 : 1.2 kbps
4.8 : 4.8 kbps
6.4 : 6.4 kbps
9.6 : 9.6 kbps
14.4 : 14.4 kbps
Response:Normal Response: OK
Error Response:ERR01
ERR05
ERR07
ERR21
ERR87 

Page 3-20NDA-24233 Issue 2
Console Command List VisuaLink 128/384 Engineering Guide
RDM2 Checking LSD Speed Setting 4-2
SDM3 Setting MLP Speed 4-3
Description: Reporting the current LSD speed by SDM2 command
Command Format:RDM2
 
Response:Normal Response: p1 OK
p1: OFF : OFF
1.2 : 1.2 kbps
4.8 : 4.8kbps
6.4 : 6.4 kbps
9.6 : 9.6 kbps
14.4 : 14.4 kbps
Error Response:ERR01
ERR05
ERR07
ERR21
ERR87
Description: Sets the Multi Layer Protocol (MLP) data port speed
• Allows for NEC far-end camera and system...

NDA-24233 Issue 2Page 3-21
VisuaLink 128/384 Engineering Guide Console Command List
RDM3 Checking MLP Speed Setting 4-4
Description: Checks the current MLP speed setting.
Command Format: RDM3
Response: Normal Response:  p1 OK
p1: OFF : OFF
4.0 : 4.0 kbps
6.4 : 6.4 kbps
14.4 :  14.4 kbps
24.0 :  24.0 kbps
Error Response:  ERR01
ERR07
ERR87 

Page 3-22NDA-24233 Issue 2
Console Command List VisuaLink 128/384 Engineering Guide
3.5  ISDN Registering/Setting Command
NDSS Registering My Number 5-1
Description: Registers a local dial number.  In a communication, a local dial number is 
reported to the remote site at a call origination.  The local number to report 
at this time is registered.  The number of digit that can be registered is 20 
digits for dial number and 8 digits for a sub address at a maximum.
Command Format: NDSS  [p1] p2 p3
p1: L11...

NDA-24233 Issue 2Page 3-23
VisuaLink 128/384 Engineering Guide Console Command List
NDSR Checking My Number Registration 5-2
Description: Checks the current local dial number setting.  In a communication, a local 
dial number is reported to the remote site at a call origination.  This is used 
to check a local dial number set by a NDSS command.
Command Format: NDSR [p1]
p1: L11 : line 1 dial No. 1
L12 : line 1 dial No. 2
L21 : line 2 dial No. 1
L22 : line 2 dial No. 2
L31 : line 3 dial No. 1
L32 : line 3...

Page 3-24NDA-24233 Issue 2
Console Command List VisuaLink 128/384 Engineering Guide
MDST Registering Speed Dial 5-3
Description: VisuaLink can register a maximum of 130 speed dial numbers.  A dial 
number that can be registered shall be 20-digit at a maximum with a sub 
address of a maximum of 8 digits, and a line speed must be set.
Command Format: MDST p1 p2 [p3] [p4] [p5]
p1: #xxx :  speed dial number (xxx: speed dial number 1-130)
p2: 0-9 :  dial Number (within 20 digits)
       :  sub address (within...