NEC Plasmasync 50xm5 Users Manual

							En-10
VIDEOVIDEO 1VIDEO 2VIDEO 3AUDIO 1DVD1 / HD1
R(MONO)LY Cb / Pb Cr / Pr
RGB2 / DVD2 / HD2
RGB 1
R/
VD G/ B/
HD
DV I
  (
Digital  RGB)
AUDIO 2R(MONO)L
AUDIO 3R(MONO)L
Cr/Pr Y Cb/Pb
RGB 3
B D C
E
F
G
H
I
J
KExternal Control
IN OUTREMOTE
A
Rear View/ Terminal Board
50/61 inch
AAC IN
Connect the included power cord here.
BEXT SPEAKER L and R
Connect speakers (optional) here. Maintain the correct
polarity. Connect the 
 (positive) speaker wire to the
 EXT SPEAKER terminal and the  (negative)
speaker wire to the 
 EXT SPEAKER terminal on
both LEFT and RIGHT channels.
Please refer to your speaker’s owner’s manual.
CVIDEO1, 2, 3 (BNC, RCA, S-Video)
Connect VCR’s, DVD’s or Video Cameras, etc. here.
VIDEO1 can be used for Input or Output.
DAUDIO1, AUDIO2, AUDIO3
These are audio input terminals.
The input is selectable. Set which video image
corresponds to the audio input from the audio menu
screen.
EDVD1 / HD1
Connect DVD’s, High Definition or Laser Discs, etc.
here.
FRGB2/ DVD2/ HD2
RGB2: You can connect an analog RGB signal
and the syncronization signal.
DVD2/ HD2: Yo u  can connect DVDs, High
Definition sources, Laser Discs, etc.
here.
This input can be set for use with an
RGB or component source.
GRGB1 (mini D-Sub 15pin)
Connect an analog RGB signal from a computer, etc.
here. This input can be used for Input or Output.HRGB3 
(DVI 24pin)
Connect a digital signal (TMDS) from a source with a
DVI output.
This input can be set for use with an RGB/PC3.
IEXTERNAL CONTROL
This terminal is used when operating and controlling
the monitor externally with a control system (by RS-
232C).
JREMOTE IN (DC +5V)
Connect the remote cable* to the remote control’s
remote jack to obtain wired remote control.
KREMOTE OUT (C-MOS DC +5V)
Connect the remote cable* to the REMOTE IN jack of
the other display monitor to obtain wired remote
control.
* The 1/8 Stereo Mini cable must be purchased separately.
PLASMA DISPLAY
VIDEO
IN
VIDEO
OUT
REMOTE
OUT
TV Tuner
REMOTE
IN
TV Tuner
Remote Control
Carrier fHz: 38kHz
Connection Example: Connecting a TV tuner
 
						

							En-11
q POWER ON/STANDBY
Switches the power on/standby.
(This does not operate when the POWER/STANDBY
indicator of the plasma is off.)
w RGB/PC
Press this button to select RGB/PC as the source.
RGB/PC can also be selected using the INPUT
SELECT button on the monitor.
eDVD / HD
Press this button to select DVD/HD as the source.
DVD/HD can also be selected using the INPUT
SELECT button on the monitor.
rVIDEO
Press this button to select VIDEO as the source.
VIDEO can also be selected using the INPUT SELECT
button on the monitor.
tMENU/ENTER
Press this button to access the OSM controls.
Press this button during the display of the main menu
to go to the sub menu.
yCURSOR (
 /  / 

 / )
Use these buttons to select items or settings and to
adjust settings or switch the display patterns.uEXIT
Press this button to exit the OSM controls in the main
menu. Press this button during the display of the sub
menu to return to the previous menu.
iPOINTER
Press this button to display the pointer.
oZOOM (+ /–)
Enlarges or reduces the image.
!0VOLUME (+ /–)
Adjusts the audio volume.
!1MUTE
Mutes the audio.
!2WIDE
Automatically detects the signal and sets the aspect ratio.
Wide button is not active for all signals.
!3DISPLAY
Displays the source settings on the screen.
!4OFF TIMER
Activates the off timer for the unit.
!5SIDE BY SIDE
Press this button to show a couple of pictures in the
side-by-side mode.
!6PICTURE IN PICTURE
Press this button to show a couple of pictures in the
picture-in-picture mode.
!7SINGLE
Cancels the split screen mode.
!8SELECT/FREEZE
Press this button to select the active picture in a split
screen mode.
When the PIC FREEZE function is operating, this button
can be used to display still images on the sub screen.
!9AUTO ADJUST
Press this button to adjust Fine Picture, Picture ADJ,
Position, and Contrast automatically. Press this button
in video mode and the Auto Adjust switches to ZOOM
mode automatically when a letter box image is
displayed.
@0ID SELECT
Set the ID number in the remote control. The remote
control can then be used only for a display with the
same ID number. When several displays are used
together they can be controlled individually.
@1CLEAR/SEAMLESS SW
Clears the number set by the ID SELECT button.
When the SEAMLESS SW function is operating, this
button can be used to switch the input source quickly.
@2Remote control signal transmitter
Transmits the remote control signals.
@3Remote Jack
Insert the plug of the remote cable (The 1/8 Stereo
Mini cable) here when using the supplied remote
control in the wired condition.
Remote Control
→ VIDEO1 → VIDEO2 → VIDEO3
 
						

							En-12
Basic Operations
POWER
To turn the unit ON and OFF:
1. Plug the power cord into an active AC power outlet.
2. Press the Power button (on the unit).
The monitor’s POWER/STANDBY indicator turns red
and the standby mode is set.
3. Press the POWER ON button (on the remote control) to
turn on the unit.
The monitor’s POWER/STANDBY indicator will light
up (green) when the unit is on.
4.
Press the POWER STANDBY button (on the remote control)
or the Power button (on the unit) to turn off the unit.
The monitor’s POWER/STANDBY indicator turns red
and the standby mode is set (only when turning off the
unit with the remote control).
VOLUME
To adjust the sound volume:
1. Press and hold the VOLUME  button (on the remote
control or the unit) to increase to the desired level.
2. Press and hold the VOLUME 
 button (on the remote
control or the unit) to decrease to the desired level.
MUTE
To mute the audio:
Press the MUTE button on the remote control to mute the
audio; press again to restore.
DISPLAY
To check the settings:
1. The screen changes each time the DISPLAY button is
pressed.
2. If the button is not pressed for approximately three seconds,
the menu turns off.
DIGITAL ZOOM
Digital zoom specifies the picture position and enlarges
the picture.
1. (Be sure ZOOM NAV is off.)
Press the POINTER button to display the pointer. ( 
 )
To change the size of the picture:
Press the ZOOM+ button and enlarge the picture.
The pointer will change to resemble a magnifying glass.
( 
  )
A press of the ZOOM- button will reduce the picture
and return it to its original size.
To change the picture position:
Select the position with the 


  buttons.
2. Press the POINTER button to delete the pointer.
AUTO ADJUST
To adjust the size or quality of the picture
automatically:
Press the AUTO ADJUST button.
Information
 AUTO ADJUST ON setting
When RGB (still picture) input is selected:
Fine Picture, Picture ADJ, Position, and Contrast will
be adjusted automatically.
When RGB (motion picture), VIDEO, or Y/Pb/Pr
(component) input is selected:
The screen size switches to ZOOM mode automatically
when a letter box image is displayed.
OFF TIMER
To set the off timer:
The off timer can be set to turn the power off after 30, 60,
90 or 120 minutes.
1. Press the OFF TIMER button to start the timer at 30
minutes.
2. Press the OFF TIMER button to the desired time.
3. The timer starts when the menu turns off.
→ 30 → 60 → 90 → 120 → 0
OFF TIMER   30
To check the remaining time:
1. Once the off timer has been set, press the OFF TIMER
button once.
2. The remaining time is displayed, then turns off after a few
seconds.
3. When five minutes remain the remaining time appears
until it reaches zero.
OFF TIMER   28
To cancel the off timer:
1. Press the OFF TIMER button twice in a row.
2. The off timer is canceled.
OFF TIMER     0
Note:
After the power is turned off with the off timer ...
A slight current is still supplied to the monitor. When you
are leaving the room or do not plan to use the system for a
long period of time, turn off the power to the monitor.
 
						

							En-13
Wide Screen Operation (manual)
With this function, you can select one of six screen sizes.
When viewing videos or digital video discs
1. Press the WIDE button on the remote control.
2.Within 3 seconds ...
Press the WIDE button again.
The screen size switches as follows:
→ NORMAL → FULL → STADIUM → ZOOM → 2.35:1 → 14:9
When a 720P or 1080I signal is input:
FULL ↔  2.35:1
When displaying enhanced split screen:
NORMAL ↔  FULL
NORMAL size screen (4:3)
The normal size screen is displayed.
* The picture has the same size as video pictures with a 4 : 3
aspect ratio.
FULL size screen
The image is expanded in the horizontal direction.
* Images compressed in the horizontal direction (“squeezed
images”) are expanded in the horizontal direction and
displayed on the entire screen with correct linearity.
(Normal images are expanded in the horizontal direction.)
STADIUM size screen
The picture is expanded in the horizontal and vertical
directions at different ratios.
* Use this for watching normal video programs (4:3) with a
wide screen.
ZOOM size screen
The picture is expanded in the horizontal and vertical
direction, maintaining the original proportions.
* Use this for theater size (wide) movies, etc.2.35:1 size screen
The squeezed film image is expanded to fulfill the entire
screen at a ratio of 2.35:1. Black bands do not appear at
the top and bottom but information is lost on the left and
right margins.
• This feature is available when the input signal is video,
component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB
(525P or 625P signal from a scan converter).
* If black bands appear on the top and bottom in the full size
screen, select the 2.35:1 size screen to fill the screen and
avoid image retention.
14:9 size screen
The image is displayed at a 14:9 aspect ratio.
* This feature is available when the input signal is video,
component (480I, 480P, 576I, 576P) or RGB (525P or 625P
signal from a scan converter).
Note:
Do not allow 4:3 content to be displayed for extended
periods of time without using gray bars. This can cause
image retention.
Information is lost on both sides.Original image


WIDE Operations
 
						

							En-14
FULL size screen
The image is expanded in the horizontal and vertical
direction.
ZOOM size screen
When wide signals are input.
TRUE
The image is true resolution.
FULL
Information
 Supported resolution
See page En-40 for details on the display output of the
various VESA signal standards supported by the
monitor.
 “PICTURE SIZE” setting
When the setting of “PICTURE SIZE” is OFF, the size
of RGB-input pictures will be TRUE in place of
NORMAL.
 When 852 (848) dot  480 line wide VGA*
signals with a vertical frequency of 60 Hz and
horizontal frequency of 31.7 (31.0) kHz are in-
put
Select an appropriate setting for RGB SELECT mode
referring to the“Table of Signals Supported” on page
En-40.
*“VGA”, “SVGA” and “SXGA” are registered
trademarks of IBM, Inc. of the United States.
Note:
Do not allow 4:3 content to be displayed for extended
periods of time without using gray bars. This can cause
image retention.
Wide Screen Operation with
Computer Signals
Switch to the wide screen mode to expand the 4 : 3 image
to fill the entire screen.
1. Press the WIDE button on the remote control.
2.Within 3 seconds ...
Press the WIDE button again.
The screen size switches as follows:
→ NORMAL → FULL → ZOOM
When displaying enhanced split screen:
NORMAL ↔  FULL
NORMAL size screen (4:3 or SXGA 5:4)
The picture has the same size as the normal computer image.
FULL size screen
The image is expanded in the horizontal direction.
ZOOM size screen
When wide signals are input.
FULL size screen
When “PICTURE SIZE” is set to “OFF”
* This cannot be set in some models. “TRUE” size will not
be displayed in such cases.
The screen size switches as follows:
→ TRUE → FULL → ZOOM
TRUE size screen (VGA, SVGA 4:3)
The image is true resolution.
 
						

							En-15
Showing a couple of pictures on the
screen at the same time
* There may be some RGB-input signals that may not be
displayed as not all signals are supported.
1. Press the button to select a screen mode from among single
mode, side-by-side, and picture-in-picture.
Note:
Picture A and B on the above screen are not always of the
same height.
Operations in the Side-by-side mode
To change the picture size, press the cursor   or 
button.
To swap the picture on the right and the left, press the
cursor 
 button.
VIDEO1RGB/PC1
AB
VIDEO1RGB/PC1
BA
To  make the desired picture active, press the SELECT/
FREEZE button.
VIDEO1RGB/PC1
AB
VIDEO1RGB/PC1
AB
SELECT/FREEZE
button
Information
Split screen operations may not function depending on
the combination of input signals. In the table below,
“	” means Yes, “” means No.
 Split screen operations may not function
depending on the frequency of the RGB
signals.
 
button
VIDEO1RGB/PC2
AB
VIDEO1RGB/PC2
AB
VIDEO1RGB/PC2
BA
VIDEO1RGB/PC2
AB
VIDEO1RGB/PC2
AB
VIDEO1RGB/PC2
BA
Side-by-Side2-R
Side-by-Side1 Side-by-Side2-L
Side-by-Side4-R
Side-by-Side3 Side-by-Side4-L
button
button
button
button
button
button
button
button
buttonbuttonbuttonbuttonbuttonbutton
SPLIT SCREEN Operations
VIDEO1
Sub 
screenMain screen
RGB/PC1
A
VIDEO1button
VIDEO1RGB/PC1
AB
SIDE BY SIDE
buttonPICTURE IN PICTURE
buttonSINGLE
button
PICTURE IN
PICTURE
button
SINGLE
button
SIDE BY SIDE
button
VIDEO1VIDEO2VIDEO3HD/DVD1HD/DVD2RGB/PC1RGB/PC2
RGB/PC3
VIDEO1				
	
VIDEO2				
	
VIDEO3				
	
HD/DVD1						
	
HD/DVD2					
	
RGB/PC1						
	
RGB/PC2					
	
Pictures
displayed on
the left/sub
screen
(Select2)
Pictures displayed on the right/main screen (Select1)RGB/PC3							

 
						

							En-16
Operations in the Picture-in-picture mode
To move the position of the sub screen, press the cursor 
or  button.
To change the size of the sub screen, press the 
 button.
VIDEO1RGB/PC1
AB
VIDEO1RGB/PC1
AB
VIDEO1RGB/PC1
AB
VIDEO1RGB/PC1
AB
 button
 button
 button
 button
To make the desired picture active, press the SELECT/
FREEZE button.
Selecting the input signals to be displayed
1. Press the SELECT/FREEZE button to make the desired
picture active.
2. Press the RGB/PC, VIDEO, or DVD/HD button.
Each press of the button changes the selection of the input
signal.
The INPUT SELECT button on the monitor can also be
used to change the selection.
Zooming in on a specific input
1. Press the SELECT/FREEZE button to make the desired
picture active.
2. Use the POINTER button and the ZOOM
/ button to
enlage the picture.
For details, see “DIGITAL ZOOM” on page En-12.
Adjusting the OSM controls
1. Press the SELECT/FREEZE button to make the desired
picture active.
2. Press the MENU/ENTER button to display the MAIN
MENU.
3. Adjust the setting to your preference.
For details, see “OSM (On Screen Menu) Controls” on
page En-17.
Note:
During enhanced split screen, some functions of OSM
controls are not available.
SELECT/
FREEZE
button
VIDEO1RGB/PC2
AB
VIDEO1RGB/PC2
AB
RGB/PC2A
B
VIDEO1A
B
VIDEO1RGB/PC2
Bottom Left Bottom Right
button
button
 button button
Top Right
button
button
 button button
Top Left
VIDEO1RGB/PC1
AB
VIDEO1RGB/PC1
AB
 
						

							En-17
Menu Operations
The OSM window is displayed with respect to the
screen as shown on the diagram.
* Depending on the screen’s mode, the OSM may be
displayed differently.
In the explanation, the OSM section is shown close up.
SEL.
MAIN MENU 1 / 2
PICTURE
AUDIO
IMAGE ADJUST
OPTION 1
ADVANCED OSM
      NEXT PAGE:   OFF
EXIT
MENU/ENTEROKEXIT
The following describes how to use the menus and the
selected items.
1. Press the MENU/ENTER button on the remote control to
display the MAIN MENU.
SEL.
MAIN MENU 1 / 2
PICTURE
AUDIO
IMAGE ADJUST
OPTION 1
ADVANCED OSM
      NEXT PAGE:   OFF
EXIT
MENU/ENTEROKEXIT
SEL.
MAIN MENU 2 / 2
      PREVIOUS PAGE
LANGUAGE
COLOR SYSTEM
SOURCE INFORMATION
EXIT
MENU/ENTEROKEXIT
2. Press the cursor buttons 
   on the remote control to
highlight the menu you wish to enter.
3. Press the MENU/ENTER button on the remote control to
select a sub menu or item.
SEL. ADJ. RETURN
PICTURE 1 / 2
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
TINT
PICTURE MODE
NR
      NEXT PAGE
:   NORMAL
:   OFF
: 52
: 32
: 16
: 32
: 32
G R
EXIT
4. Adjust the level or change the setting of the selected item
by using the cursor buttons 

   on the remote control.
5. The adjustments or settings are then stored in memory.
The change is stored until another change is made.
6. Repeat steps 2 – 5 to adjust an additional item, or press
the EXIT button on the remote control to return to the
main menu.
* When adjusting using the bar at the bottom of the screen,
press the 

 or  button within 5 seconds. If not, the
current setting is stored and the previous screen appears.
Note: The main menu disappears by pressing the EXIT
button.
Information
 Advanced menu mode
When “ADVANCED OSM” is set to “ON” in the main
menu (1/2), full menu items will be shown.
SEL.
MAIN MENU 1 / 2
PICTURE
AUDIO
IMAGE ADJUST
OPTION 1
OPTION 2
OPTION 3
OPTION 4
ADVANCED OSM
      NEXT PAGE:   ON
EXIT
MENU/ENTEROKEXIT
*The actual screen may be different from the ones
in this manual.
OSM (On Screen Menu) Controls
 
						

							En-18
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
PICTURE CONTRAST←→  0←52→72 YES En-20
BRIGHTNESS←→  0←32→64 YES En-20
SHARPNESS←→  0←16→32 YES En-20
COLOR←→  0←32→64 YES En-20
TINT R←→G     0←32→64 YES En-20
PICTURE MODE BRIGHT/NORMAL/THEAT.1/THEAT.2/DEFAULT YES En-20
NR OFF/NR-1/NR-2/NR-3 YES En-20
COLOR TEMP. LOW/MID LOW/MID/HIGH YES En-20
WHITE BALANCE GAIN RED←→  0←40→70 YES En-21
GAIN GREEN←→  0←40→70 YES En-21
GAIN BLUE←→  0←40→70 YES En-21
BIAS RED←→  0←40→70 YES En-21
BIAS GREEN←→  0←40→70 YES En-21
BIAS BLUE←→  0←40→70 YES En-21
RESET OFF←→ON YES En-21
GAMMA 1←→2←…
→4 YES En-21
LOW TONE *
3AUTO←→1←…
→3 YES En-21
COLOR TUNE RED Y←→M0←32→64 YES En-21
GREEN C←→Y0←32→64 YES En-21
BLUE M←→C0←32→64 YES En-21
YELLOW G←→R0←32→64 YES En-21
MAGENTA R←→B0←32→64 YES En-21
CYAN B←→G0←32→64 YES En-21
RESET OFF←→ON YES En-21
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
AUDIO BASS←→  0←13→26 YES En-22
TREBLE←→  0←13→26 YES En-22
BALANCE L←→R -22←0→+22 YES En-22
AUDIO INPUT1 VIDEO 1-3 / HD/DVD 1-2 / RGB 1-3 YES En-22
AUDIO INPUT2 VIDEO 1-3 / HD/DVD 1-2 / RGB 1-3 YES En-22
AUDIO INPUT3 VIDEO 1-3 / HD/DVD 1-2 / RGB 1-3 YES En-22
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
IMAGE ADJUST ASPECT MODE NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9/TRUE*3— En-22
V-POSITION←→-64←0→+64 YES En-22
H-POSITION←→-128←0→+127 YES En-22
V-HEIGHT←→0←→64 YES En-22
H-WIDTH←→0←→64 YES En-22
AUTO PICTURE OFF←→ON*
2NO En-22
FINE PICTURE*1←→*20←→64 YES En-22
PICTURE ADJ.*1←→*20←→128 YES En-22
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
OPTION1 OSM DISPLAY OSM OFF←→ON YES En-23
OSM ADJ. 1←…
→6 YES En-23
OSM ANGLE H←→V YES En-23
OSM ORBITER OFF←→ON YES En-23
OSM CONTRAST LOW←→NORMAL YES En-23
BNC INPUT RGB←→COMP. YES En-23
D-SUB INPUT RGB— En-23
RGB SELECT AUTOYES En-23
HD SELECT 1080B/1035I/1080A NO En-24
INPUT SKIP OFF←→ONYES En-24
ALL RESET OFF←→ON— En-24
           :Shaded areas indicate the default value.
←→
: Press the 
 or  button to adjust.
           :Menu items in a ruled box are available when the ADVANCED OSM is set to ON.
Menu Tree
 
						

							En-19
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
 OPTION2 PWR. MGT. OFF←→ONYES En-25
CINEMA MODE OFF←→ONYES En-25
LONG LIFE PLE AUTO/LOCK 1/LOCK 2/LOCK 3 YES En-25
ORBITER AUTO 1 YES En-26
AUTO 2 YES En-26
MANUAL H-DOT/V-LINE/TIME YES En-26
OFF YES En-26
INVERSE OFF YES En-26
ON WORKING TIME/WAITING TIME YES En-26
WHITE YES En-26
SCREEN WIPER OFF YES En-27
ON WORKING TIME/WAITING TIME/SPEED YES En-27
SOFT FOCUS OFF/1/2/3/4 YES En-27
GRAY LEVEL 0←…
→3←…
→15 YES En-27
S1/S2 AUTO←→OFFYES En-28
PICTURE SIZE*
3OFF←→ONYES En-28
DVI SET UP PLUG/PLAY PC←→STB/DVD NO En-28
BLACK LEVEL LOW←→HIGH NO En-28
CLOSECAPTION OFF←→CC1~4←→TEXT1~4 YES En-28
CAPTION CONT. LOW←→NORMAL YES En-28
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
 OPTION3 TIMER PRESENT TIMEDAYLIGHT SAVING TIMEOFF←→ON NO En-29
DAY/HOUR/MINUTES NO En-29
PROGRAM OFF YES En-29
ON DATE/ON/OFF(HOUR, MINUTES)/INPUT/FUNCTION YES En-29
MULTI REPEAT OFF YES En-30
ON MULTI MODE/WORK TIME/INPUT MODE YES En-30
PWR. ON MODE INPUT LAST /MULTI/ VIDEO 1-3 / HD/DVD 1-2 / RGB 1-3 YES En-30
VOLUME LAST←→0←…
→44 YES En-30
CONTROL  LOCK OFF←→ONYES En-30
IR REMOTE OFF←→ONYES En-31
LOOP OUT OFF←→ONYES En-31
REMOTE ID ALL←→1←…
→4 NO En-31
ID NUMBER ALL←→1←…
→256 YES En-31
VIDEO WALL DIVIDER OFF/1/4/9/16/25 YES En-32
POSITION
No.1←…
→No.4/No.7←…
→No.15/No.16←…
→No.31/No.32←…
→No.56—En-32
DISP. MODE SPLIT←→BLANK YES En-32
AUTO ID OFF←→ON YES En-32
IMAGE ADJUST ASPECT MODE NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9/TRUE*
3—En-33
V-POSITION/H-POSITION/V-HEIGHT/H-WIDTH/AUTO PICTURE/
FINE PICTURE*
1/PICTURE ADJ.*1
P. ON DELAY OFF/ON/MODE1/MODE2 YES En-33
PLE LINK OFF←→ON YES En-33
REPEAT TIMER OFF YES En-34
ON DIVIDER/SOURCE/WORK TIME YES En-34
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
 OPTION4 SUB. PICTURE SUB. P DETECT OFF←→AUTO YES En-34
DISPLAY FADE←→NORMAL YES En-34
SUB. P RATE 20%←…
→100% YES En-34
ZOOM NAV OFF←→S BY S←→BTM LFT←→BTM RGT←→TOP RGT←→TOP LFT YES En-34
PIC FREEZE OFF←→S BY S1←→S BY S2←→BTM LFT←→BTM RGT←→TOP RGT←→TOP LFT YES En-35
SEAMLESS SW OFFYES En-35
ON SELECT1/SELECT2 YES En-35
TEXT INSERT OFF/TOP/MID HIGH/MID LOW/BOTTOM YES En-36
INPUT/PIC. RATE/DISPLAY YES En-36
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCE
ADVANCED OSM OFF←→ONYES En-36
LANGUAGE ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/
У/PORTUGUÊS NO En-36
COLOR SYSTEM AUTO/3.58NTSC/4.43 NTSC/PAL/PAL 60/PAL-N/PAL-M/SECAM NO En-37
SOURCE INFORMATION——En-37
*1 Only when AUTO PICTURE is OFF
*2 RGB/PC only
*3“PICTURE SIZE”, “TRUE” and “LOW TONE” are only for 50 and 61 inch types.
Information
 Restoring the factory default settings
Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.