NEC Neax2000 Ivs Small Platform System Manual

ND-46551 (E) CHAPTER 3
Page 149
Revision 2.0
NAP-200-010
Sheet 7/7
System Initialization and 
System Data Entr y
DESCRIPTION DATA
Assign the type of signaling (DTMF) for Outgoing 
and Bothway Trunk Routes..YY = 01
(1) Trunk Route No. (00 - 63)
(2) 7
Specify the DTMF Sender characteristics to match 
the distant office..YY = 24 (DTMF Inter Digital Pause)
(1) Trunk Route No. (00 - 63)
.YY = 26 (DTMF Sender Signal Width)
(1) Trunk Route No. (00 - 63)
(2) 0/1 : 64ms/128ms
.YY = 46 (DTMF Sender Release...

CHAPTER 3 ND-46551 (E)
Pag e 1 50
Revision 2.0
NAP-200-011
Sheet 1/1
Operation Test
1. OPERATION TEST
Confirm the entered system data and hardware, including cable connection, by completing the following operational
tests.
• Basic Connection Test at MDF
- Station Line Test (Operator Call from all stations)
- Central Office Trunk Test (Incoming, Outgoing)
- Tie Line Trunk Test (Incoming, Outgoing)
• Service Feature Test
- Call Transfer
- Step Call
- Executive Right of Way
- Call Hold
- Call Back
- Call...

ND-46551 (E) CHAPTER 3
Page 151
Revision 2.0
NAP-200-012
Sheet 1/1
Cleaning and Visual Check
1. CLEANING
Clean the following places:
• Inside of the main equipment, especially the bottom of the base.
• On the Top Cover.
• Around the Main Equipment and the MDF.
• Keyboard on the Attendant Console.
2. VISUAL CHECK
(1) Check to see if all circuit cards are in their positions correctly.
(2) Check that the cable connections in the PIM are correctly and completely connected, and the routing of the
cables has...

CHAPTER 3 ND-46551 (E)
Pag e 1 52
Revision 2.0
NAP-200-013
Sheet 1/1
Mounting of the Front Cover
1. MOUNTING OF THE FRONT COVER
Mount the Front Cover onto PIM and attach them with screw provided.
Figure 013-1  Mounting of the Front Cover
PIM
FRONT
FRONT COVER 

ND -4 6551 ( E)  CHAPTER 4
CHAPTER 4  OFFICE  D ATA P ROGRAM MING 

CHAPTER 4 ND-46551 (E)
Pag e 1 54
Revision 2.0
1.2.2 Station Data
In this table, the following data are required.
• Station Number: Station numbers (up to four digits), specified in the Numbering Plan Table, are assigned.
For the Multiline Terminal station, specify the Primary Extension Number.
• Type of Telephone
The type of station telephone set is specified as shown below.
TYPE OF TEL  DESCRIPTION 
DP ................................... Dial Pulse Telephone set
PB ......................................

ND-46551 (E) CHAPTER 4
Page 155
Revision 2.0
• NUMBER OF LINE
Specify the number of trunks to be provided with each route (IC-Incoming, OG-Outgoing, BW-Bothway).
• DP/PB
Specify the type of address signal from/to distant office, as shown below.
TYPE OF TEL DESCRIPTION 
DP ................................... Dial Pulse 
PB ................................... DTMF Signal
• KIND OF SIGNAL
Specify the kind of signaling system such as Ring Down, Loop, E & M etc. at the line.
1.2.4 Station Hunting Group Data...

CHAPTER 4  ND -4 6551 ( E)
1.2 .6   Speed C allin g-S yste m  D ata
L EV EL 3
L EV EL 2
Sta ti on  No.
LEV EL 7/T ru nk No.
P ri m ary  E xte n si on Nu mber
L EV EL 3
L EV EL 2
Not  t o  b e
L EV EL 7
Sta ti on  No.Pri m ary  E xte n si on Nu mber 

ND-46551 (E) CHAPTER 4
Page 157
Revision 2.0
PN-AUC
PN-2DLC• The station number must be assigned to the 1st 
LEN (LEVEL 0) and/or 2nd LEN (LEVEL 1) of 
each LT slot.
• For the PN-2DLC, specify the Primary Extension 
Numbers of Multiline Terminal as shown below.
PN-4COT
PN-4DIT• The trunk number must be assigned to the 1st LEN 
(LEVEL 0) through 4th LEN (LEVEL 3) of each 
LT  s l o t .
PN-AUC
PN-2ODT• The trunk number must be assigned to the 1st LEN 
(LEVEL 0) and/or 2nd LEN (LEVEL 1) of each LT 
slot....

CHAPTER 4 ND-46551 (E)
Pag e 1 58
Revision 2.0
PN-2DAT • The card number must be assigned to the 1st LEN 
(LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT 
slot.
PN-8RST • The card number must be assigned to the 1st LEN 
(LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT 
slot.
Note :When using the internal DTMF Receiver on
the MP card, assign the Card No. E200 to the
LEN No. 0124.
PN-DK00 • The card number must be assigned to the 1st LEN 
(LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT 
slot.
• The card numbers...