NEC Neax2000 Ivs Small Platform System Manual

ND-46551 (E) CHAPTER 3
Page 119
Revision 2.0
NAP-200-007
Sheet 4/11
Installation of SN716 DESKCON
(c) MDF Cross Connection via PN-PW00 Power Option (see Figure 007-4)
Figure 007-4  MDF Cross Connection via PN-PW00 Power Option
26 Bx 1 Ax
LTC0 (J)
1Ax26Bx
(P)
LEN0000
1 Grd 26 -48V
2 Grd 27 -48V
(P)
MDF
LEN0000
Ax
Bx
Ax
Bx
PN-8DLCPIM0
1
26
1
2
3
4
5
6
MODULAR
TERMINALPW00
Grd
-48V
Grd
-48V
SN716 DESKCON 

CHAPTER 3 ND-46551 (E)
Pag e 1 20
Revision 2.0
NAP-200-007
Sheet 5/11
Installation of SN716 DESKCON
(1) Handset Installation
Screw the handset support onto the bottom of the console.
Figure 007-5  Mounting of Handset Support to SN716 DESKCON 

ND-46551 (E) CHAPTER 3
Page 121
Revision 2.0
NAP-200-007
Sheet 6/11
Installation of SN716 DESKCON
(2) Headset Installation
Plug the headset into the modular jack (H/S 0 or H/S 1) located at the bottom of the console.
Figure 007-6  Headset Installation for SN716 DESKCON
HAND
H/S 0
H/S 1 

CHAPTER 3 ND-46551 (E)
Pag e 1 22
Revision 2.0
NAP-200-007
Sheet 7/11
Installation of SN716 DESKCON
(3) Line Cord Connection
Plug the line cord into the modular jack (LINE) located at the bottom of the console. For the MDF cross
connection for the SN716 DESKCON, refer to Figure 007-7.
Figure 007-7  Cable Connection to SN716 DESKCON
PBX
DLC 1P MDF
MODULAR
TERMINAL
SN716 DESKCON3P 3P
PW00
2P
LINE CORD
PAGE REC LINE 

ND-46551 (E) CHAPTER 3
Page 123
Revision 2.0
NAP-200-007
Sheet 8/11
Installation of SN716 DESKCON
(4) AC-DC ADAPTER Connection
When using an AC-DC ADAPTER for power supply, plug the AC-DC ADAPTER into the “12V~24VDC”
terminal located at the rear of the console.
Figure 007-8  AC-DC ADAPTER Connection to SN716 DESKCON
AC-DC ADAPTER
RS-232 12V~24VDC 

CHAPTER 3 ND-46551 (E)
Pag e 1 24
Revision 2.0
NAP-200-007
Sheet 9/11
Installation of SN716 DESKCON
(5) Using PW00 Card
When using the PW00 card for power supply, provide the PW00 card according to the following procedure.
(a) Mount the PW00 card into the LT01-LT10 slot or AP5 slot.
Figure 007-9  Mounting PW00 Card into PIM
BUILT-IN BATTERY
Note: The PW00 card occupies the adjoining left side (smaller number) slot because of its two-story
structure.
PIM
P
W
R...

ND-46551 (E) CHAPTER 3
Page 125
Revision 2.0
NAP-200-007
Sheet 10/11
Installation of SN716 DESKCON
(b) Connect the PW00 card and SN716 DESKCON by installation cable as shown in Figure 007-10 and
Figure 007-11.
Figure 007-10  PW00 Card Connection to SN716 DESKCON
PW86
PW00
CONN Connector
PWR0C
PIMPWR1
TO DESKCON 

CHAPTER 3 ND-46551 (E)
Pag e 1 26
Revision 2.0
NAP-200-007
Sheet 11/11
Installation of SN716 DESKCON
(6) 6.MDF Cross Connection
(a) When using PN-8DLC
Figure 007-11  MDF Cross Connection for SN716 DESKCON
33T7338
R7832
T6327
R6727
T12726
T026
2
1
MDF
R01
R12
LEN0000     (No. 0)
PIM0
P
PN-8DLC
LT00LTC0
J
LEN0001     (No. 1)
LEN0006     (No. 6)
LEN0007     (No. 7)
•
••
••
••
•
1R026T0
2R127T1
7R632T6
8R733T7
(P)
26 T0 1 R0
27 T1 2 R1
32 T6 7 R6
33 T7 8 R7LEN0000
LEN0001
LEN0006
LEN0007
LTC0 (J)
•
••
••
••...

ND-46551 (E) CHAPTER 3
Page 127
Revision 2.0
NAP-200-008
Sheet 1/13
Switch Setting of Circuit Card
1. CIRCUIT CARDS SWITCH SETTING
Table 008-1 shows the control circuit cards and Table 008-2 shows the line/trunk circuit cards to be explained in this
NAP. As for the other circuit cards, refer to the Circuit Card Manual.
*MB=Make BusyTable 008-1 Control Circuit Cards
NAME
(FUNCTIONAL 
NAME)EXISTENCE OF 
LAMPS
X: PROVIDED
—: NOT PROVIDEDEXISTENCE OF 
SWITCHES
X: PROVIDED
—: NOT PROVIDEDEXTRACTION/INSER-...

CHAPTER 3 ND-46551 (E)
Pag e 1 28
Revision 2.0
NAP-200-008
Sheet 2/13
Switch Setting of Circuit Card
2. PN-CP03 (MP)
(1) Locations of Lamps, Switches, and Connectors
Figure 008-1  PN-CP03 (MP) Card
(2) Lamp Indications
Table 008-3  PN-CP03 (MP) Card Lamp Indications
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 120 IPM while the circuit card is operating normally.
CLKIN Green Lights while receiving clock signals to the PLO oscillator.
SW3
RUN
SW1
SW2
CLK
JP0
RS1
JACK
VR
RS0
JP1