NEC Neax 2400 Ipx Office Data Specification

NDA-24298 CHAPTER 2
 Page 17
Issue 1
ASSIGNMENT
5. IPX MAT Commands
The IPX MAT’s operation is very similar to that of the NEAX2400 MS-DOS MAT, so you will find that many
of the key stroke operations have been carried over into IPX MAT. In addition, some standard MS Windows
operations and key strokes are used. Use the following keys, or in some instances the mouse, to select or enter
data.
6. Configuring IPX MAT
This section explains the PBX Alias parameters you may configure using the PBX Administration...

CHAPTER 2 NDA-24298
Page 18
Issue 1
ASSIGNMENT
6.1 Serial/Direct Connection
The following steps explain how to configure the PBX Alias for a serial/direct connection using the
recommended default data.
Note 1:The PBX Alias cannot have spaces in the name.
Note 2:You can use other data when configuring IPX MAT. However, it is recommended that you use the default
data as previously described when configuring a new PBX Alias.
Table 2-3 PBX Administration Default Values
PBX Alias NEAX-IPX
Connection Type...

NDA-24298 CHAPTER 2
 Page 19
Issue 1
ASSIGNMENT
1. From the PBX menu, select Configuration to open the PBX Administration dialog box.
Figure 2-20   PBX Administration
2. Enter a name for the PBX Alias in the PBX Alias box.
Note:You can also define a PBX Alias by selecting the default NEXT-IPX or by modifying any other previously
defined Alias from the list in the PBX Alias box. If you select a PBX Alias from the list, its related
information displays in the additional fields on this dialog box. You can...

CHAPTER 2 NDA-24298
Page 20
Issue 1
ASSIGNMENT
12. Leave the IP Port text box blank.
13. Leave the Inter-App Resource text box blank.
14. Click Add to write the data.
15. Click Close.
Note:The PBX Administration dialog box changes adapting to EX-FCCS Network. Enter the Fusion Group
Number (FUG) which the PBX to be logged-in belongs. “Connection Timeout”, “Response Timeout”, and
“Pacing Timer” text box is not provided. Others are the same as previous one. The PBX dialog box is as
shown below.
6.2 TCP/IP...

NDA-24298 CHAPTER 2
 Page 21
Issue 1
ASSIGNMENT
Note:
If your IPX is to reside on your existing LAN, you will need to obtain an available IP address from your
System Administrator before you configure the PBX Alias.
6.2.1 Modifying or Adding a PBX Alias
Note:
The PBX Alias cannot have spaces in its name.
The following steps explain how to create a PBX Alias in IPX MAT. 
1. From the PBX menu, select Configuration to open the PBX Administration dialog box.
2. Enter a name for the PBX Alias in the PBX Alias...

CHAPTER 2 NDA-24298
Page 22
Issue 1
ASSIGNMENT
6.2.3 Starting the PBX System
Before you can log in to the PBX with your IPX MAT, you must start the PBX system. To start the PBX
system, please see the NEAX2400 IPX Installation Manual.
If you start up the system when the PBX is in DM Clear Restart mode, (the SENSE Switch is set to the
default value “1”), you must verify that the IPX MAT baud rate is set to 4800 to ensure that the system
runs properly.
6.2.4 Logging in to IPX
After you have defined the PBX...

NDA-24298 CHAPTER 2
 Page 23
Issue 1
ASSIGNMENT
6.2.5 Assigning System Data
This section explains how to assign the IP Address and the SubNet Mask using the default IP Address
172.16.253.0 and the default SubNet Mask 00.00.00.00. Both fields must be entered using their
hexadecimal equivalents.
Note:You may find it convenient to use the Calculator in the Windows Accessories to find the hexadecimal
equivalent of the IP Address and the SubNet Mask. To convert from decimal to hexadecimal:
1. Select...

CHAPTER 2 NDA-24298
Page 24
Issue 1
ASSIGNMENT
16. Type 516 in the INDEX text box and press Enter.
17. Type 10 (hexadecimal equivalent of 16) in the DATA text box and press Enter.
18. Type Y in the WRT? text box and press Enter.
19. Type 1 in the SYS text box and press Enter.
20. Type 517 in the INDEX text box and press Enter.
21. Type FD (hexadecimal equivalent of 253) in the DATA text box and press Enter.
22. Type Y in the WRT? text box and press Enter.
23. Type 1 in the SYS text box and press Enter....

NDA-24298 CHAPTER 2
 Page 25
Issue 1
ASSIGNMENT
6.2.6 IPX MAT File Operations
The IPX MAT creates three types of files; Command Log files, Office Data Backup files, and List-up
Command Report data tables. Command Log files and List-up Command Report data tables are the only
files a user needs to view. The Office Data Backup files are used strictly for saving and storing the PBX
Office Data.
6.2.6.1 Office Data Backup
It is always a good idea to routinely backup the data from the IPX memory to its...

CHAPTER 2 NDA-24298
Page 26
Issue 1
ASSIGNMENT
6.2.6.2 MEM_HDD
The following steps explain how to perform the backup and restore of PBX data to the PBX hard drive.
1. Enter MEM_HDD in the Run Command field on the IPX MAT main menu.
2. Press Enter.
3. The Backup and Restore dialog box displays.
4. Select Memory to Hard Disk in the Direction Select list.
5. Select Data Memory in the Data Type Selection list.
6. Select Auto Verify if you want to verify the data. This is an optional step.
7. Click Start....