NEC Neax 2400 Imx Installation Manual

NDA-24234 CHAPTER 3
Page 261
Revision 3.0
INSTALLATION PROCEDURE
12. SELECTION OF CONFIGURATION ITEM
Using a numeric key, press the desired number in Configuration Menu. A menu for assigning configuration
data appears. Assign configuration data referring to “Assignment of Configuration Data” on the next page.
Figure 016-21  Selecting a Configuration Item
NAP-200-016
Sheet 31/41
Installation of the DESK CONSOLE and 
Cable Connection
Alarm
LDN TIE Busy ATND NANS Recall
EMG BV TRKSL Call Park SC SVCPAGE...

CHAPTER 3 NDA-24234
Pag e 26 2
Revision 3.0
INSTALLATION PROCEDURE
13. ASSIGNMENT OF CONFIGURATION DATA
This section explains how to assign each configuration data. When assigning configuration data, the following shad-
ed keys are used.
Figure 016-22  Assigning Configuration Data
NAP-200-016
Sheet 32/41
Installation of the DESK CONSOLE and 
Cable Connection
Alarm
LDN TIE Busy ATND NANS Recall
EMG BV TRKSL Call Park SC SVCPAGE
StartREC
[SRC key]
Night
Position BusyMute
DEST
SRC 3 DEF2 
ABC 1 L 6
L 5
L 4...

NDA-24234 CHAPTER 3
Page 263
Revision 3.0
INSTALLATION PROCEDURE
14. HEADSET/HANDSET
This item specifies an optional device connected to the HAND H/S0 connector.
Note:With regard to the H/S1 connector, only the Headset is connected. Accordingly, data assignment for H/S1
connector is not required.
(d) Press the desired number. An asterisk shows the selected number.
1. Headset is connected to the HAND H/S0 connector
2. Handset is connected to the HAND H/S0 connector
SRC: Return to Configuration Menu...

CHAPTER 3 NDA-24234
Pag e 26 4
Revision 3.0
INSTALLATION PROCEDURE
15. HEADSET TYPE
This item specifies the type of Headset connected to the H/S1 connector.
(d) Press the desired number. An asterisk shows the selected number.
1. The type of Headset is “SUPRA”
2. The type of Headset is “COROLLE”
SRC: Return to Configuration Menu
Note:Default setting is “1: SUPRA”.
(b) Press the SRC key. The display returns to Configuration Menu.
(c) When configuration data assignment is finished, proceed to UPDATING...

NDA-24234 CHAPTER 3
Page 265
Revision 3.0
INSTALLATION PROCEDURE
16. MUTE
This item specifies On/Off setting of the mute function for the HAND H/S0 or H/S1 connector. While the
mute function is set to On, if the Mute key is pressed, the voice at the DESK CONSOLE side is not sent to
the other party.
(a) Press the desired number. An asterisk shows the selected number.
1. Both H/S0 and H/S1 are set to On
2. Only H/S0 is set to On
3. Only H/S1 is set to Off
SRC: Return to Configuration Menu
Note:Default...

CHAPTER 3 NDA-24234
Pag e 26 6
Revision 3.0
INSTALLATION PROCEDURE
17. REC CONTROL
This item specifies the operation mode of a recording device. The following two types of modes are available:
Manual mode
Manual mode is available when the REC circuit card is mounted in the system. When the REC key is
pressed, the system starts recording and the REC lamp lights. When the REC key is pressed again, the re-
cording stops and the REC lamp goes off.
Automatic mode
In Automatic mode, a dedicated recording...

NDA-24234 CHAPTER 3
Page 267
Revision 3.0
INSTALLATION PROCEDURE
18. SUP CONNECTION
This item specifies whether the supervisory console is connected or not.
(a) Press the desired number. An asterisk shows the selected number.
1. Supervisory Console is connected
2. Supervisory Console is not connected
SRC: Return to Configuration Menu
Note:Default setting is “1: NONE”.
(b) Press the SRC key. The display returns to Configuration Menu.
Note:Do not change this data.
(c) When configuration data assignment is...

CHAPTER 3 NDA-24234
Pag e 26 8
Revision 3.0
INSTALLATION PROCEDURE
19. REC VOLUME ADJUSTMENT
This item specifies the recording level of the received voice from the other party. Note that the voice level at the
operator side cannot be adjusted.
(a) Press the desired number. An asterisk shows the selected number.
1. +2dB Up
2. 0dB (Standard level)
3. -4dB Down
4. -8dB Down
SRC: Return to Configuration Menu
Note:Default setting is “2: 0dB”.
(b) Press the SRC key. The display returns to Configuration Menu....

NDA-24234 CHAPTER 3
Page 269
Revision 3.0
INSTALLATION PROCEDURE
20. BLF
This item specifies On/Off setting of the BLF function. When using BLF function, system data assignment is
also required.
(a) Press the desired number. An asterisk shows the selected number.
1. BLF Available
2. BLF Not available
SRC: Return to Configuration Menu
Note:Default setting is “2: DISABLE”.
(b) Press the SRC key. The display returns to Configuration Menu.
(c) When configuration data assignment is finished, proceed to...

CHAPTER 3 NDA-24234
Pag e 27 0
Revision 3.0
INSTALLATION PROCEDURE
21. HOLD/START/RELEASE/SWAP
This item specifies the locations of HOLD, START and RELEASE key.
(a) Press the desired number. An asterisk shows the selected number.
1. Original setting
2. Swapped setting
Note:The locations of each key changes as shown below.
SRC: Return to Configuration Menu
Note:Default setting is “1: ORIGINAL”.
(b) Press the SRC key. The display returns to Configuration Menu.
(c) When configuration data assignment is...