NEC Neax 2400 Imx Installation Manual

NDA-24234 CHAPTER 3
Page 221
Revision 3.0
INSTALLATION PROCEDURE
9. CROSS CONNECTIONS FOR D
term Series E
Note 1:
Provide the necessary cross connections at the MDF using copper wires of 0.5 mm diameter (24 AWG). 2-
core twisted wire is used for speech path, and single-core wire is used for control wire. It is recommended
that wires of different colors be used for trunks, station lines, PFT, etc., so that they can easily be distin-
guished.
Note 2:The maximum distance between the Module Group and Dterm...

CHAPTER 3 NDA-24234
Pag e 22 2
Revision 3.0
INSTALLATION PROCEDURE
Figure 015-14  Cable Connection for  D
term Series E
NAP-200-015
Sheet 23/30
Cable Termination and Cross 
Connections from MDF to Peripheral 
Equipment, C. O. Lines, and Tie Lines
PBX
LT connector Cable
LT connectorELCA0
A15B0
B15MDF
Max 850 m. (2459 feet)1-pair cable(Jack) Modular Block
Modular Cable
Provide the following connections at the MDF.
D        Series Eterm 

NDA-24234 CHAPTER 3
Page 223
Revision 3.0
INSTALLATION PROCEDURE
10. CROSS CONNECTIONS FOR DIGITAL INTERFACES
Perform the cross connections for digital interfaces as shown below:
Note 1:When your system is single IMG configuration, time division switch (TSW) card is equipped with Phase
Lock Oscillator (PLO). Therefore no dedicated PLO card is required to use Digital Interfaces. However,
when the system requires a higher-precision oscillator, use the Oscillator (OSC: PA-CK14) card. The cards
may be...

CHAPTER 3 NDA-24234
Pag e 22 4
Revision 3.0
INSTALLATION PROCEDURE
Figure 015-15  PLO Pin Assignments for Receiving Clock (Single IMG Configuration)
NAP-200-015
Sheet 25/30
Cable Termination and Cross 
Connections from MDF to Peripheral 
Equipment, C. O. Lines, and Tie Lines
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Front View
PIM0
PLO
PLO TSWTSW
Universal Slots Universal Slots
PIN
No.
26
27
28
29
30
31
32
33LEAD
NAME
DCSB0
DIU0B0
DIU1B0
DIU2B0
DIU3B0
SYN0B0
SYN1B0LEAD
NAME...

NDA-24234 CHAPTER 3
Page 225
Revision 3.0
INSTALLATION PROCEDURE
Figure 015-16  PLO Pin Assignments for Receiving Clock (Multiple IMG Configuration)
NAP-200-015
Sheet 26/30
Cable Termination and Cross 
Connections from MDF to Peripheral 
Equipment, C. O. Lines, and Tie Lines
EXCLK0
EXCLK1
TSWMBackplane
PLO input leads appear on the LT connectors labeled EXCLK0 and EXCLK1.
PLO mounting slots
PLO card is mounted in slots 21 and 23 of TSWM
.
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21...

CHAPTER 3 NDA-24234
Pag e 22 6
Revision 3.0
INSTALLATION PROCEDURE
Figure 015-17  Cable Connection Diagram for Accepting Synchronization Clocks 
from an External High-Stability Oscillator (Single IMG Configuration)
NAP-200-015
Sheet 27/30
Cable Termination and Cross 
Connections from MDF to Peripheral 
Equipment, C. O. Lines, and Tie Lines
PLO
MDF PBX
PCM Cable (IP) PCM Cable (IP)
DCSA0
DCSB0
LT Connector Cable
DCSB1
DCSA1 TSW
BASEUmaximum 400 meters (1320 feet)   (24AWG)
External
High-Stability...

NDA-24234 CHAPTER 3
Page 227
Revision 3.0
INSTALLATION PROCEDURE
Figure 015-18  Cable Connection Diagram for Accepting Synchronization Clocks 
from an External High-Stability Oscillator (Multiple IMG Configuration)
NAP-200-015
Sheet 28/30
Cable Termination and Cross 
Connections from MDF to Peripheral 
Equipment, C. O. Lines, and Tie Lines
EXCLK0
EXCLK1
MDF IMG1
PCM Cable (IP) PCM Cable (IP)
DCSA
DCSB Cable
“EXCLK1”
DCSB
DCSA Cable
“EXCLK0”
PLO#1
PLO#0
BASEUmaximum 400 meters (1320 feet)   (24AWG)...

CHAPTER 3 NDA-24234
Pag e 22 8
Revision 3.0
INSTALLATION PROCEDURE
Figure 015-19  Cable Connection Diagram for Distributing Clock from a Digital Interface (Single IMG 
Configuration)
NAP-200-015
Sheet 29/30
Cable Termination and Cross 
Connections from MDF to Peripheral 
Equipment, C. O. Lines, and Tie Lines
PLO
maximum 100
meters (330 feet)
MDF IMG1
PCM
Carrier
Equipment/
DSU
CLK PCM Cable (2P) LT Connector 
TSW
BASEUto other node
RA
RB
TA
TB
POUTA
POUTB
DIU0A0
DIU0B0
DIU1A0
DIU1B0
DIU2A0
DIU2B0
DIU3A0...

NDA-24234 CHAPTER 3
Page 229
Revision 3.0
INSTALLATION PROCEDURE
Figure 015-20  Cable Connection Diagram for Distributing Clock from a Digital Interface 
(Multiple IMG Configuration)
NAP-200-015
Sheet 30/30
Cable Termination and Cross 
Connections from MDF to Peripheral 
Equipment, C. O. Lines, and Tie Lines
EXCLK1
EXCLK0
maximum 100
meters (330 feet)
MDF IMG1
PCM
Carrier
Equipment/
DSU
CLK PCM Cable (2P) LT Connector 
“EXCLK0”
“EXCLK1” PLO#0
PLO#1
BASEU
to other node
RA
RB
TA
TB
POUTA
POUTB
DIU0A
DIU0B...

CHAPTER 3 NDA-24234
Pag e 23 0
Revision 3.0
INSTALLATION PROCEDURE
This NAP explains the installation of the DESK CONSOLE and Cable Connection. Figure 016-1 shows the outer
view of the DESK CONSOLE. Use the PA-CS33 (ATI) card as an interface card between the system and the DESK
CONSOLE. The card can connect a maximum of two DESK CONSOLEs.
Figure 016-1  Outer View of Desk Console
NAP-200-016
Sheet 1/41
Installation of the DESK CONSOLE and 
Cable Connection
START
Cable running While referring to Figure...