NEC Neax 2400 Imx Installation Manual

NDA-24234 CHAPTER 3
Page 91
Revision 3.0
INSTALLATION PROCEDURE
5. INSTALLATION OF CPR
This Section explains the procedure to install the CPR into the LPM. Perform the following ([1] through [5]) for
both CPR0 and CPR1.
1. Using the Phillips Screwdriver, remove the 4 + 8 screws. Then, detach the front panel and top cover from
the CPR. (Refer to Figure 009-4.)
Figure 009-4  Removal of Front Panel and Top Cover from CPR
NAP-200-009
Sheet 7/11
Setting of Switch Positions and 
Mounting of Circuit Cards
AT T...

CHAPTER 3 NDA-24234
Page 92
Revision 3.0
INSTALLATION PROCEDURE
2. Depending on the system configuration, insert the ISAGT (PZ-GT13/16) and LANI
(PZ-PC19) cards into the following slots of the CPR (refer to Figure 009-5):
ISAGT (PZ-GT13/16)
→Slot #6 (ISA) (Fixed)
LANI 
→Slot #0 (PCI) (For Fusion Link)
LANI 
→Slot #1 (PCI) (When connecting MAT via 10-BASE T and PCI buses)
LANI 
→Slot #3 (PCI) (When LANI for Fusion Link is in dual configuration: avail-
able for Release 3 or later software)
Figure 009-5...

NDA-24234 CHAPTER 3
Page 93
Revision 3.0
INSTALLATION PROCEDURE
3. Attach the top cover and front panel again by fastening the removed screws. (Refer
to Figure 009-6.)
Figure 009-6  Reattachment of CPR Top Cover and Front Panel
NAP-200-009
Sheet 9/11
Setting of Switch Positions and 
Mounting of Circuit Cards
AT T E N T I O NContents
Static Sensitive
Handling
Precautions Required
Top Cover
CPRFront Panel
After mounting the ISAGT/LANI cards, reattach the top cover by tightening the 8 screws.
Then, also...

CHAPTER 3 NDA-24234
Page 94
Revision 3.0
INSTALLATION PROCEDURE
4. After turning “ON” the MBR key on the DSP of the CPR, insert the CPR into the
LPM. Then, fasten the four screws. (Refer to Figure 009-7.)
Figure 009-7  Accommodation of New CPR into LPM
NAP-200-009
Sheet 10/11
Setting of Switch Positions and 
Mounting of Circuit Cards
AT T E N T I O NContents
Static Sensitive
Handling
Precautions Required
CPR LPM
As shown in the figure below, insert the CPR into the LPM. Then, fasten the four screws.  

NDA-24234 CHAPTER 3
Page 95
Revision 3.0
INSTALLATION PROCEDURE
5. Finally, insert the HFD into the CPR. Then, fasten the two screws. (Refer to Figure
009-8.)
Figure 009-8  Insertion of New HFD into CPR
NAP-200-009
Sheet 11/11
Setting of Switch Positions and 
Mounting of Circuit Cards
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
LPM
HFD (PZ-IO27/28)
By using the two screws, fasten the HFD onto the CPR. 

CHAPTER 3 NDA-24234
Pag e 96
Revision 3.0
INSTALLATION PROCEDURE
This NAP explains how to run the following internal cables between Modules.
NAP-200-010
Sheet 1/71
Internal Cable Connections
START
Confirm connector locations Referring to Figures 010-1 through 010-4, 
confirm the locations of the connectors into 
which the internal cables are inserted.
Connection of FANU cables Referring to the figures listed in Figures 010-4 
through 010-9, connect FANU cables.
Connection of Internal Power Cables...

NDA-24234 CHAPTER 3
Page 97
Revision 3.0
INSTALLATION PROCEDURE
 
Since Cable connections vary depending on the system configuration which includes how many Port Interface Mod-
ules (PIMs) are accommodated in the system or whether redundancy is taken into account as to the CPU. Before
starting cable connections, find your system in “Quick Reference Table.” When you find your system in the table,
open the related pages, on which necessary information is provided, and then set about the cable connections....

CHAPTER 3 NDA-24234
Pag e 98
Revision 3.0
INSTALLATION PROCEDURE
NAP-200-010
Sheet 3/71
Internal Cable Connections 
Table 010-1  Quick Reference Table (2/6)
SYSTEM TYPE KIND OF CABLE FRAME NAME FIGURE TABLE
Power CableIMG0010-13 010-6
IMG1010-16 010-9
Internal CableIMG0010-30 010-19
IMG1010-33 010-22
Inter-Frame Bus Cable IMG0-IMG1011-1 011-1
011-2 011-2
Inter-Frame
Alarm Bus CableIMG0-IMG1011-11 011-11
Power CableIMG0010-13 010-6
IMG1010-17 010-10
Internal CableIMG0010-30 010-19
IMG1010-34 010-23...

NDA-24234 CHAPTER 3
Page 99
Revision 3.0
INSTALLATION PROCEDURE
NAP-200-010
Sheet 4/71
Internal Cable Connections 
Table 010-1  Quick Reference Table (3/6)
SYSTEM TYPE KIND OF CABLE FRAME NAME FIGURE TABLE
Power CableIMG0010-13 010-6
IMG1010-17 010-10
IMG2010-19 010-12
Internal CableIMG0010-30 010-19
IMG1010-34 010-23
IMG2010-35-
Inter-Frame Bus CableIMG0-IMG1011-1 011-1
011-2 011-2
IMG1-IMG2011-4 011-4
Inter-Frame
Alarm Bus CableIMG0-IMG1011-11 011-11
IMG0-IMG2011-12 011-12
Power CableIMG0010-13 010-6...

CHAPTER 3 NDA-24234
Pag e 10 0
Revision 3.0
INSTALLATION PROCEDURE
 
NAP-200-010
Sheet 5/71
Internal Cable Connections 
Table 010-1  Quick Reference Table (4/6)
SYSTEM TYPE KIND OF CABLE FRAME NAME FIGURE TABLE
Power CableIMG0010-13 010-6
IMG1010-17 010-10
IMG2010-21 010-14
Internal CableIMG0010-30 010-19
IMG1010-34 010-23
IMG2010-37-
Inter-Frame Bus CableIMG0-IMG1011-1 011-1
011-2 011-2
IMG1-IMG2011-6 011-6
Inter-Frame
Alarm Bus CableIMG0-IMG1011-11 011-11
IMG0-IMG2011-12 011-12
Power CableIMG0010-13...