NEC Neax 2000 Ivs2 Business/Hotel/Data Features And Specifications

ATTENDANT CAMP-ON
NEAX2000 IVS2
   Business/Hotel/Data Features and SpecificationsPage 18 NDA-24271, Issue 1.0
ATTENDANT CAMP-ON
General Description
This feature permits the Attendant to hold an incoming call in a special mode when the desired station for the
transfer is busy. The Attendant sends a Camp-On tone to the busy station. When that station becomes idle, it is
automatically alerted and connected to the waiting party.
Station Application
Attendant Consoles.
Operating Procedure
To activate a...

ATTENDANT CAMP-ON
NEAX2000 IVS2
Business/Hotel/Data Features and Specifications  
NDA-24271, Issue 1.0  Page 19
3. Dial the Call Hold feature access code. The original call is placed on Call Hold and the station user is auto-
matically connected to the Camp-On call.
From a Multiline Terminal
1. Receive a Camp-On tone.
2. Hang up and receive incoming ring.
3. Lift the handset and converse.
OR
1. Receive a Camp-On tone.
2. Press the Answer key. The call in progress is placed on Call Hold and the Camp-On...

ATTENDANT CONSOLESN610 ATTCON
NEAX2000 IVS2
   Business/Hotel/Data Features and SpecificationsPage 20 NDA-24271, Issue 1.0
ATTENDANT CONSOLE
SN610 ATTCON
General Description
The Attendant Console (SN610 ATTCON) operates on a switched-loop basis with a maximum of 6 Attendant
loops terminating at each console on the associated interface card. The Attendant uses these loops for answering,
originating, holding, extending, and re-entering calls. When Attendant loop release is used, the number of loops
is...

ATTENDANT CONSOLEAttendant Called/Calling Name Display
NEAX2000 IVS2
Business/Hotel/Data Features and Specifications  
NDA-24271, Issue 1.0  Page 21
Service Conditions
1. Each Firmware Processor (FP) can support up to 8 Attendant Consoles (SN610 ATTCON/SN716
DESKCON). A maximum of 8 Attendant Consoles (SN610 ATTCON/SN716 DESKCON) can be support-
ed per system.
2. Each SN716 DESKCON uses a 3-pair cable. This cable cannot be longer than 4000 feet (1200 meters).
3. The SN716 DESKCON is equipped with an...

ATTENDANT CONSOLEAttendant Called/Calling Number
NEAX2000 IVS2
   Business/Hotel/Data Features and SpecificationsPage 22 NDA-24271, Issue 1.0
3. The trunk name display is provided on a trunk route basis. The maximum amount of characters in the trunk
name display is four. The maximum number of trunk names assignable is 63. Only the MAT or CAT can
be used to record or change a trunk name.
4. There are two ways to change a name that is currently programmed: Overwriting with a new name or erasing
it by...

ATTENDANT CONSOLEAttendant Call Selection
NEAX2000 IVS2
Business/Hotel/Data Features and Specifications  
NDA-24271, Issue 1.0  Page 23
Attendant Call Selection
General Description
This feature allows assignment of keys on the Attendant Console to particular types of trunk routes (such as
WATS or FX) and particular types of service calls (such as Attendant recalls, intercept calls, etc.). LEDs indicate
the type of incoming call and pressing the associated key allows the Attendant to answer the calls in...

ATTENDANT CONSOLEAttendant Console Lockout – Password
NEAX2000 IVS2
   Business/Hotel/Data Features and SpecificationsPage 24 NDA-24271, Issue 1.0
Operating Procedure
To set Attendant Console Lockout
1. Press an idle LOOP key. The associated green LED lights.
2. Dial the feature access code or press the MODE key. The associated red LED lights. The LCD displays
ACTIVE during normal mode and the green LED of the ACTIVE key lights.
3. Press the LKOUT key. The associated red LED lights. The LCD display...

ATTENDANT CONSOLEAttendant Do Not Disturb Setup And Cancel
NEAX2000 IVS2
Business/Hotel/Data Features and Specifications  
NDA-24271, Issue 1.0  Page 25
Attendant Do Not Disturb Setup And Cancel
General Description
The Attendant has the ability to enter and remove individual stations from Do Not Disturb (DND). Additionally,
the Attendant can set one preassigned group of stations into, or out of, Do Not Disturb.
Operating Procedure
To set an individual station in DND
1. Dial the station number without...

ATTENDANT CONSOLEAttendant Interposition Calling/Transfer
NEAX2000 IVS2
   Business/Hotel/Data Features and SpecificationsPage 26 NDA-24271, Issue 1.0
Attendant Interposition Calling/Transfer
General Description
This feature allows any Attendant to directly converse with another Attendant and also allows Attendants to
transfer calls from their console to another Attendants console in systems where Multiple Console Operation
has been provided.
Operating Procedure
To call from console A to console B
1....

ATTENDANT CONSOLEAttendant Listed Directory Number
NEAX2000 IVS2
Business/Hotel/Data Features and Specifications  
NDA-24271, Issue 1.0  Page 27
Operating Procedure
To set the SN610 ATTCON into the Lamp Check Mode
1. Press the NIGHT key to set the Attendant Console in Night Mode.
2. Disconnect the line cord modular plug from jack in the bottom of the Attendant Console.
3. Reconnect the modular plug while pressing “0” on the dial of the Attendant Console.
4. The following message is displayed on the LCD...