NEC Neax 2000 Ivs Ccis Features And Specifications

							NEAX2000 IVS CCIS Features and Specifications
Page 60NDA-24159, Issue 2
Individual Attendant Access - CCIS
General Description
This feature permits a station user to call a specific Attendant Console, in the CCIS network, using an individual
Attendant Identification Number.
Operating Procedure
1. The station user dials an individual Attendant Identification Number.
2. The Attendant at the directed Attendant Console receives an Incoming Call Identification indication and can
answer using the normal operating procedures.
Service Conditions
1. An Attendant Identification Number must be assigned to each Attendant Console.
2. This feature is available when the Attendant Console is attached to the main NEAX2400 IMS, in the CCIS
network. 
						

							NEAX2000 IVS CCIS Features and Specifications
NDA-24159, Issue 2
Page 61
LDN Night Connection - CCIS
General Description
This feature routes Listed Directory Number (LDN) calls to a preselected station, in the CCIS network, when
the Night mode has been entered.
Operating Procedure
No manual operation is required.
Service Conditions
1. The maximum number of LDNs is eight.
2. The destination party is assigned to Day/Night mode.
Examples:
A. There is an Attendant Console in the same office.
DAY Incoming to Attendant Console in the same office.
NIGHT Incoming to station or TAS line in the other office.
B. There is an Attendant Console in the other office.
DAY Incoming to Attendant Console in the other office.
NIGHT Incoming to station or TAS line in the same office.
3. When the NEAX2000 IVS system is in the Night mode, a DID incoming call with an LDN from another
switching office through CCIS can be routed to a preselected TAS line or station in the NEAX2000 IVS sys-
tem. 
						

							NEAX2000 IVS CCIS Features and Specifications
Page 62NDA-24159, Issue 2
Link Alarm Display - CCIS
General Description
This feature provides an indication on external equipment when the CCIS link is connected/disconnected, when
the system is initialized, or when the CCH is in make-busy.
Operating Procedure
No manual operation is required.
Service Conditions
1. An external equipment is to be provided by the customer and to be connected with a PN-DK00 card.
2. The indication is as follows:
3. When the CCH (PN-SC00) is in make-busy, an external indication is provided about one minute later.Status Indication
Link disconnected ON
Link connected
OFF
System Initialized
ON
CCH make busy
ON 
						

							NEAX2000 IVS CCIS Features and Specifications
NDA-24159, Issue 2
Page 63
Message Waiting Lamp Setting - Attendant - 
CCIS
General Description
This feature allows an Attendant, in the NEAX2400 IMS system, to set or cancel a Message Waiting lamp in-
dication, through the CCIS network, on a station in a NEAX2000 IVS system.
Operating Procedure
To set a Message Waiting indication from the NEAX2400 IMS ATTCON:
1. Press an idle LOOP key; receive dial tone.
2. Dial the Message Waiting feature access code (maximum of three digits); receive feature dial tone.
3. Dial the station number; receive special set tone.
4.Message Waiting indication is set.
5. Press the RELEASE key to return to an idle condition.
To cancel a Message Waiting indication:
1. Press an idle LOOP key; receive dial tone.
2. Dial the Message Waiting cancellation code (maximum of three digits); receive feature dial tone.
3. Dial the station number; receive special set tone.
4.Message Waiting indication is canceled.
5. Press the CANCEL key to return to an idle condition.
Service Conditions
1. The Message Waiting lamp on a Single-Line Telephone or a Multiline Terminal is lit when this feature is
activated.
2. If an Attendant attempts to set Message Waiting to a station which already has Message Waiting set, the At-
tendant will receive service set tone.
3.Message Waiting indications are retained when the system is initialized.
4. An Attendant Console or station in the NEAX2000 IVS system does not have the facility to set or cancel a
Message Waiting lamp on a station at another switching office, through CCIS. 
						

							NEAX2000 IVS CCIS Features and Specifications
Page 64NDA-24159, Issue 2
Message Waiting Lamp Setting - Attendant - CCIS
5. A 4LCD card is required to provide Single Line Telephones with the Message Waiting function. Single Line
Telephones must be equipped with Message Waiting lamps for 70VDC.
MWL ON/OFFATT  STA
STA
MWL
NEAX2000 IVS NEAX2400 IMS
CONTROL 
						

							NEAX2000 IVS CCIS Features and Specifications
NDA-24159, Issue 2
Page 65
Message Waiting Lamp Setting - Station - CCIS
General Description
This feature allows a station user, in the NEAX2400 IMS system, to set or cancel a Message Waiting lamp in-
dication, through the CCIS network, to a station in the NEAX2000 IVS system with this feature.
Operating Procedure
To set a Message Waiting indication:
1. Lift the handset; receive dial tone.
2. Dial the Message Waiting feature access code (maximum of three digits); receive feature dial tone.
3. Dial the desired station number; receive service set tone.
4.Message Waiting indication is set at the station.
To cancel Message Waiting indication:
1. Lift the handset; receive dial tone.
2. Dial the Message Waiting cancellation code (maximum of three digits); receive feature dial tone.
3. Dial the desired station number; receive service set tone.
4.Message Waiting indication at station is canceled.
Service Conditions
1. If a station attempts to set Message Waiting to a station which already has Message Waiting set, the station
will receive service set tone.
2. This service can be allowed or denied by Class Of Service.
3.Message Waiting indications are retained when the system is initialized.
4.Message Waiting for one station can be controlled from the Attendant Console and any other station at the
same time.
5.Message Waiting cannot be activated on a Multiline Terminal virtual line.
6. An Attendant Console or station in the NEAX2000 IVS system does not have the facility to set or cancel a
Message Waiting Lamp on a station at another switching office, through CCIS. 
						

							NEAX2000 IVS CCIS Features and Specifications
Page 66NDA-24159, Issue 2
Message Waiting Lamp Setting - Station - CCIS
7. If the recipient of the Message Waiting is a NEAX2000 Multiline Terminal without a Message Waiting key
assigned, the LCD will indicate MSGX. When scrolling through Message Waiting indications, the station
number which set the Message Waiting will not be indicated.
8. A 4LCD card is required to provide Single Line Telephones with the Message Waiting function. Single Line
Telephones must be equipped with Message Waiting lamps for 70VDC.
MWL ON/OFFATT  STA
STA
MWL
NEAX2000 IVSNEAX2400 IMS
CONTROL 
						

							NEAX2000 IVS CCIS Features and Specifications
NDA-24159, Issue 2
Page 67
Miscellaneous Trunk Access - CCIS
General Description
This feature provides access to all types of external and customer-provided equipment/facilities, such as Tie Line
and exchange network, along with Dictation, Paging Access - CCIS and Code Calling through the CCIS net-
work.
Operating Procedure
No manual operation is required.
Service Conditions
1. Access to these trunk routes is allowed or denied via Class Of Service - Individual.
2. An interface circuit must be provided for each required trunk.
3.Miscellaneous Trunk Access - CCIS is programmed in system data via the Maintenance Administration Ter-
minal (MAT) or the Customer Administration Terminal (CAT). 
						

							NEAX2000 IVS CCIS Features and Specifications
Page 68NDA-24159, Issue 2
Miscellaneous Trunk Restriction - CCIS
General Description
This feature denies certain stations and dial-repeating tie trunks access to specific trunk groups, such as Tie Line,
exchange network, Dictation or Paging Access - CCIS through the CCIS network.
Operating Procedure
No manual operation is required.
Service Conditions
1. Restricted call attempts will receive reorder tone.
2. Station line access to a given miscellaneous trunk group is controlled by assigning a Route Restriction Class
(RSC) to each line. There can be a maximum of eight different RSCs (1-8) per system, each of which can be
programmed to restrict an assigned station from none, one, or more than one miscellaneous trunk group
(maximum of 64 trunk groups).
3. This feature can be assigned to stations or dial-repeating tie trunks in Class Of Service - Individual restric-
tions.
4. If a station user’s Class Of Service - Individual allows outgoing route completion via the Attendant, the sta-
tion user can dial the Attendant access code for completion of miscellaneous trunk calls.
5. The Call Transfer - All Calls feature will operate as follows:
• If the restricted station line is the second party, this station cannot add a trunk from which this station is
restricted.
• If the restricted station line is not the second party, the second party cannot connect the restricted station
line to a trunk from which the station is normally restricted.
• If a restricted station user calls another station, the called station cannot use the Call Transfer feature to
connect the calling station to a trunk group to which the restricted station is denied dial access. If a transfer
is attempted, the second party station will receive an immediate transfer recall.
6.Night Service: Restrictions can be changed for a given station when the system is in the Night mode of op-
eration.
7.Tie Line Access: If the station user accesses a tie trunk to a distant PBX, access to outside exchanges can only
be controlled by the distant PBX.
8.Miscellaneous Trunk Restriction - CCIS is programmed in system data via the Maintenance Administration
Terminal (MAT) or the Customer Administration Terminal (CAT). 
						

							NEAX2000 IVS CCIS Features and Specifications
NDA-24159, Issue 2
Page 69
Multiple Call Forwarding - All Calls - CCIS
General Description
This feature allows the last hop of a Multiple Call Forwarding - All Calls sequence to be forwarded over a CCIS
network to a station in another office.
Operating Procedure
To set Call Forwarding - All Calls from a Single-Line Telephone:
1. Lift the handset; receive dial tone.
2. Dial the Call Forwarding - All Calls feature access code; receive feature dial tone.
3. Dial the outgoing trunk access code; receive a single burst of service set tone.
(This operation is required for a network using Open Numbering Plan.)
4. Dial the desired target station number and receive service set tone.
5. Wait approximately five seconds; receive service set tone.
To cancel Call Forwarding - All Calls from a Single-Line Telephone:
1. Lift the handset; receive dial tone.
2. Dial the Call Forwarding - All Calls cancellation code; receive service set tone.
To set Call Forwarding - All Calls from the Attendant Console:
1. Press an idle LOOP key.
2. Dial the Call Forwarding - All Calls feature access code; receive feature dial tone.
3. Dial the originating station number.
4. Dial the outgoing trunk access code; receive a single burst of service set tone.
(This operation is required for a network using Open Numbering Plan.)
5. Dial the desired target station number and receive service set tone.
6. Press the RELEASE key.
To cancel Call Forwarding - All Calls from the Attendant Console:
1. Press an idle LOOP key.
2. Dial the Call Forwarding - All Calls cancellation code; receive feature dial tone.
3. Dial the originating station number; receive service set tone.
To set Call Forwarding - All Calls from a Multiline Terminal:
1. Lift the handset or press the SPKR key; receive dial tone.
2.
Press the 
Call Forwarding - All Calls feature access key; receive feature dial tone.