NEC Electra 616 General Installation Manual

_. _____~. __. __._ __.._ _--___ .-.---..--- -----.- ---.-----... -.--“I-- --.” --.... ___ --------.h 
USER DIALS 
A DIGIT ON 
A COlPBX LINE 
ALLOW USER 
FREE DIALING 
ALLOW PBX 
ACCESS CODE 
l+ DIAL AREA DIRECT DIAL AREA 
0 
0 
l-9 
. 
1 
DIGIT TOLL 
Fig. 340-26 Electra-616 Toll Denial Algorithm 
Page 300 -34  

pm SECTllON 400 STATION OPERATION PROCEDURE 
410 Key Telephone Operation 
410.1 CO/P5X (Outside Calls) 
1. Originating 
Using Manual Dialing 
- 
depress idle (unlit) m 
- 
- 
- 
a 
- 
- 
-  - 
lift handset or depress 3 q 
- receive dial tone 
- 
dial desired number 
- 
when party answers, use handset .to talk 
Using Last CO/PBX Number Redial 
Use of station or system Speed Dialing can automat- 
ically seize an acceptable COjPBX line eliminating 
the need to depress II CO/PBX 
line. For 4 pnrticubu...

Removing a CO/PBX Line from Hold 
- 
depress fluttering or intermittent winking Ic6 
- lift handset 
4. Hold Recall 
An audible recall signal, a fluttering COIPBX LED 
and a display are provided to idle keysets that have 
longer than the programmable time. 
- 
display shows IT] 
X corresponds to CO line recalling 
- 
depress fluttering m 
- lift handset 
Note: Display will indicate the held lines of the station 
sequentially, for 0.8 set each. 
5. Abandoning a Call 
Abandoning a Call 
- 
at the end of...

a 
--. 
410.3 Conferencing 
r 
Note: When 
the conference circuit is busy, g will light 
cl 
on all keysets. No additional conferences can be 
made at this time. 
The 
allowable conference configurations are: 
2 stations 1 CO/PSX line 
1 stations 2 CO/PBX lines 
3 stations No CO/PBX lines 
1. Originating 
Three Party Conference 
(1 station 2 CO/PBX lines or 2 stations 1 CO/PBX 
line) 
with CO or ICM call in progress 
depress m, El flashes 
originate CO or ICM call and wait for called 
party to answer...

, _..^_,.. _ - _ _.-_.. /. ___---- .._._I..-... I- ._” . . .- _..^..., -- .-.- I ..-_ _ . ___I -._-....._._.___ . ,_j___..__._,,_. - . ..” . . 
- on keypad dial - 
use handset to talk ! 
II 
for Internal Zone 1 X digit dialed on keypad 
121 for Internal Zone 2 
To a Busy Door Phone 
i for Internal Zone 3 
141 for All Internal Zones - lift handset or depress s 
I 
- 
depress door phone key 
- 
display shows 1-1 
- 
X digit dialed on keypad display shows r] 
- 
on keypad dial m or 121 
2. External Paging...

4 
- dial telephone number 
- each digit is displayed as dialed [T] 
- 
depress I] Key 
- 
display goes Off 
Note: Each Key Telephone has 16 SPD buffers, 16 digits 
each, available for its own use. 
2. 
To Program System Speed Dial 
(Attendant Keyset Only) 
- 
depress -1 Key 
- 
record tone is heard over speaker 
- 
display shows [m 
- dial desired buffer number m] 
- record tone stops 
- dial telephone number 
- each digit is displayed as dialed 171 
- depress 1 SPD PfiOG ] Key 
- display goes off 
Note...

410.11 Security Alarm . 
Display shows [Tj or (nlzl 
1. To Cancel Alarm 
With Key Telephone Idle 
- depress m 
- display shows [F] 
- on keypad dial 171, 181 
- display shows [T] 
- depress B 
- 
alarm stops, display will remain until circuit is reset. 
After reset, display goes out. 
-_ Page 400-6  

._ 
.- 
. . 
I J 
.  

This addendum supplements the Electra-616 Installation Service -Manual 
ND-17314. This addendum should be used whenever a CRJ-SA KTU is 
installed in an B-6-( 
) KSU and when an EIXH-( ) Key Telephone Set with 
built-in speakerphone is installed in an Electra-616 system. Because all 
ES-6-3 KSUs initially contain a CFU-SA KTU it is recorrmended that all 
installation and maintenance personnel become familiar with this addendum. 
i . 
:  

/ 
-. 
This addendum is divided into four sections: 
100 E;T-6H-( ) Key Telephone Set with Internal Speakerphone 
200 CharqesinStardard ProgramingwithCIlU-SA 
300 
Menu Prqraming 
400 
How to Operate New Features 
Access Code List 
Alphanumeric Display Character List 
-2-