NEC Electra 616 General Installation Manual

4. hklte: 77~1 lines cnn be omitted from fhe scm. Station Class Assignment (See Fig. 31-O-20) 
This program area is used in assigning restfictions to 
Each station is assigned an address where selection can 
be made on which lines to scan Addresses 19 - 34 cor- 
spond to a station and buttons 1 - 6 of each address 
represents the lines. The default value is that all stations 
scan from lines 2 to 1. 
340.5 
Memory Block 4 
1. CO/PSX Line Assignment (See Fig. 340-I 7) 
This program area assigns lines as...

7. Speed Dial Toil Override Assignment (See Fig. 340-23) 
This area of the program is used to permit or deny Toll 
Restricted Stations using the System Speed Dial access 
numbers 40 - 59 to override toll restriction. This choice 
only applies to system speed dial memory access 
numbers 40 - 59 and all toll restricted stations on a 
system wide basis. Address 16 button 8 is used to allow 
or disallow system speed dial buffers 40 - 59 toll over- 
ride. The default value is that System Speed Dial will...

_ - ..--.------. .--. -_ i’ 
Tabse 340.1 Memory Block and Address Content 
MEMORY BLOCK 1 
Address 1 Recall Button Timing Assiwment 
2 Pause Timing Assignment 
3 Paging Timeout Assignment 
4 Hold Recall Timing Assignment 
5 System Refresh Basis 
MEMORY BLOCK 2 
Address I - 12 Day Mode CO/PBX Ringing Assignment 
13- 24 
Night Mode CO/PBX Ringing Assignment 
15 Door Phone Assignment 
16- 19 Door Phone Chime Assignment 
20- 21 Off-Hook Ringing Assignment 
MEMORY BLOCK 3 
Address 1 - 4 Internal 
Paging Zone...

F 
MEMORY BLOCK : 1 
ADDRESS 
: 7 
EXAMPLE: 
I 
Recall Timing is set at 0.6 seconds. 
Fig. 340-I Real! Button Assignment 
I MEMORY BLOCK : 4 
I ADGRESS 
EXAMPLE: 
I-JZJ 
3.5 
Pause Timing is set at 3.5 seconds. 
. 
Fig. WI-2 Pause Timing Assignment 
Page 300-17  

30 
60 
I MEMORY BLOCK : 1 
1 ADDRESS : 3 
EXAMPLE: 
I 
Paging Time out Is se1 at 60 seconds. 
1: 
Fig. 340-3 Paging Time Out Assignment 
I MEMORY BLOCK : 7 
! 
I ADDRESS : 4 
EXAMPLE: 
rJ-q 
60 
Hold Recall Timing is se: at 60 seconds. 
Fig. 3404 Ho!d Recall Timing  

, ‘1 
I 
MEMORY BLOCK : f 
---.-____ 
-___ 
ADDRESS 
:5 I 
EXAMPLE: ,j15j 
System is Programmed for 
Idle Condition: 
Fig. 340-5 System Refresh Basis 
I MEMORY BLOCK : 2 
i- 
ADDRESSES 
: 7 - 12 
In the Day Mode, CO/PBX-3 wil! ring at 
Stations 1 thru 7. 
Psge 300-19  

In the Might Mode CQ,&‘BX 1 - 6 will ring 
at Station 1 thru 5. 
Fig. 340-T Night Mode COiPBX Ringing Assignment 
MEMORYBLOCK : 2 
ADDRESS : 75 
EXAMPLE: 
Door Phone 1 and 2 are enabled. 
Fig. 340-8 
Door Phone Assignment 
-_- Page 300 -20  

I MEMORYBLCCK : 2 
I 
AEERESSES : lS- 19 
EXAMPLE: 
Door Phone 1 will chime at Stations 2,4, 6, and 8. 
STATeON NUMBERS 
NO OFF-HOOK 
RINGING 
OFF-HOOK 
El 
RINGING 
I 16 I 1 I 21 31 41 51 6/ 7j 8 
/ 17 
I 9 / 10 j 11 1 12 / 13 / 14 / 15 / 76 I I I I I I I 
I I 
18 
1 
2 
I / ! I8 
19 
9 16 
Fig. 340-9 Ooor Phone Chime Assignment 
I MEMORY BLOCK : 2 I 
ADDRESSES : 20-21 
EXAMPLE: 
pm ga E /zI III 
Stations 1 thru 4 will ring off-hook. 
Page 300 -2 I  

, .‘_ 
EXAMPLE: 
I 
STA. 5: ZONE A 
STA. 6: ZONE B 
STA. 7: ZONE C 
STA. 8: NO ZONE 
ADD. STATiON NW.‘?BERS 
3 9 10 11 j 72 
- 
4 13 / 
j 14 15  ! 
/ l6 
Fig. 343-l 1 Internal Paging Zone Assignment 
Page 300 -22  

, 
/ 
i 
MEMORY BLOCK : 3 
/ 
STA. 
1 
2 
3. 
4 
5 
6 
7 
8 
9 
10 
11 
12 
13 
14 
15 
16 ADDRESS 
: 5 
IIIlmm141 
lzHzzml[81 EXAMPLE: 
q 
,Stations 7 and 10 are assigned as Attendant 
Stations 
_ ‘^----_._,_^i.~ 1 
_,_.t 
I 
1 2 3 141.6 6 7 I8 
ADD. 
/ ATT. 
STi+TlQPd / ATT.STATION , / 
5 
Fig. 340-l 2 Attendant Station Assignment 
Page 300 -23