NEC Electra 616 General Installation Manual

100 ET-6%()KEYTELEPEKlNESETwI?xINrFPNAL spEAKERP= 
110 Installation 
From a hardware stardpoint, the EZXiE+( ) Key Telephone 
set is installed exactly as the ET-6-I ) Key Telephone set. 
Cable and connector requirements remain the same. No local 
power source need be provided for the ET+%-( 
) speakerphone. 
I.20 Programunir-q 
In order to initiate intercom calls with the ET-BI-( ) 
internal speakerphone, the station must be assigned as a 
hands-free telephone in the system program. See Figure 12O.l.A....

1 MEMORY BLOCK: 9 1 
. . . 
L 
I ET-6H-( ) 
I 
ET-6-( ) 
I 
I ADDRESS : 2-3 1 
STATIONS 1 _ 4 ARE 
ASSIGNED AS ET-GH-(. ) 
STATIONS 5 u 8 ARE 
ASSIGNED AS ET-6-t ) _ 
Figure 120-l A: Hands-free Telephone Assignment. 
-6-  

200 CHAG~INSIANDAPDPIUQUMIING 
210 Programming Operations 
All programming procedures remain standard as in Section 
300 of the Electra-616 Installation Service Manual NE-17314. 
This includes all procedures for going off-line, for selecting 
memory blocks and addresses, for entering data, etc. 
210.1 
Programming Details 
Several parameters have been added to the programrrable 
contents of the system memory, these are: 
--Privacy release which disables privacy on selected 
lines enabling up to four...

220 Default Values / . 
The default values 
--Privacy release: 
feature. for these additional parameters are: 
All a/P%X lines retain the privacy 
--All stations are m-6-( 
) Key Telephone sets (no 
internal speakerphone). 
--Tandem Conference is allowed when station 8 is not 
installed; when station 8 is installed there is no Tar&m 
confererxe allowed unless another station position with 
no station installed is chosen and programned. 
230 Progrananing Details 
230.1 Memory 
Block 8 
1) System Reset....

Reset occurs at this time with the progrming station returning 
to ton-line mode. 
230.2 Memory Block 9 
1) Privacy Release Assignment (See Figure 340-27). Any 
ccambination of cO/PBX lines can be selected to lose the privacy 
feature. This enables up to four 
stations to 
join a 
conversation with an outside party on the chosen CD/PBX line 
without privacy. Parties attempting to enter after a fourth 
party has entered will receive error tone. 
The default value is 
that all CD/PBX lines retain the...

unsupervised two CD/PE3X line conference with exit and re-entry 
available to the station which originated the copfereme. 
Address 4, buttons 4 - 8 are used to designate the 
station position reserved for tandem 
conference. The 
corresponding SW-S K!TU must be installed. If the selected 
.station is later installed it will take precedence and the 
tandem conference feature will becune inoperative. The default 
value is that the position of station 8 is reserved for tandem 
conferences. 
-e-  

I ALLOW 1 MEMORY BLOCK: 9 1 
ADDRESS 
CO/PBX lines 1 thru 3 will 
allow privacy release. 
Figure 340-27: Privacy Release EnaQie Assignment 
1 MEMORY BLOCK: 9 ] 
1 ADDRESSES : 2-3 / 
Stations 1 thru 4 are assigned as Hands-Free Te!. 
Stations 5 thru 8 are assigned as Standard Tel. 
1~00 I STATION NUMBERS 
2 1 2 3 4 5 617 81 
i 
3 9 10 11 12 13 14 115 16 
Figure 340-28: Hands-Free Telephone Assignment  

/ 
/ f 
1 
1 MEMORY BLOCK: 9 j 
ADDRESS - :4 1 
Station 16 is assigned 
Tandem Conference Line 
q 6 
c 
STA 
1 
2 
3 
4 
5 
6 
7 
8 
9 
10 
11 
12 
13 
14 
15 
16 
cl 
El 
t3 
I3 El 
Kl 
I3 
I3 
Kl 
Figure 340-29 . - bandem Conference Line Assignment 
K.,,. 
_ 
1n -  

300 MlMJPxxEWT4ING 
Menu programming is a new method of programming the 
Electra-616. Menu programming supplements the standard system 
programming and can be performed partially from the programming 
station (Station 1) and partially from each individual station. 
Not all parameters can be changed via the menu prograrmning mode. 
Parameters which can be programmed from station 1 using 
the menu mcde are: 
--Feature Assignment - one of 48 possible selections is 
chosen to fit the system requirements (See...

310 Menu ProgramninJ From Keyset 1 
1) Feature Assignment (1 &&rough 48) 
* m: This programing utilizes the Feature ’ 
Assigrrment Menu table and all access codes 
are determined from Table 3OC-1A_ 
--choose access code (l-48) from Table 300-lA 
--place programing overlay (when available) on 
station keyset 1 
--depress /m key (or MENJ PEW CUT a on 
overlay) 
--depress [oN/oFrl key (or EXIT a on overlay) 
--depress -1 key (or a on overlay) 
--on keypad dial access code (1~ 48) 
--depress F key (er 
MENU...