Namco Gunmen Wars Service Manual

							Page 41
6. ADJUSTMENTS
6-1 Turning  on  the  Power
After the machine has been installed, turn ON the power. The power
switch is located on the rear of the monitor cabinet.

 

 


Adjustment or maintenance on this machine should be carried out by
qualified personnel only.
  
Einstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.
  
Justeringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
  
Los ajustes y el mantenimiento de esta máquina deben ser realizados
sólo por personal cualificado.
  
L’installation, le service, le réglage, ou la maintenance doivent être
effectués uniquement par les personnes qualifiées.
  
Μετατρπές ή επιδιρθώσεις στα µηανήµατα πρέπει να γίννται
µν  απ  ευσιδτηµένα  άτµα.
  
Regolazioni e manutenzione su questa macchina devono essere fatti
solo da personale specializzato.
  
Justering eller vedlikehold på denne maskinen skall bare utføres av
kvalifiserte personell.
  
Aanpassingen of onderhoud aan deze machine dient alleen
uitgevoerd te worden door bekwaam personeel.
	 		 	
	Afinações ou manutenção nesta maquina, deverão ser efectuadas
sómente por pessoal qualificado.

 

 


Justeringar och underhåll på denna maskin skall endast utföras av
kvalificerad personal.
  
Tätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden
omaava henkilökunta.   
						

							

\fOIN  \fOUNTERTEST SER VI\fE
ENTER
UP
SELE\fT DOWN 2  Amp  Q/B 
(\foin  Fuse)
PLAYER 1UP
SELE\fT DOWN
PLAYER 2
SERVI\fE
ENTER
TEST
6-2 Adjustment  Switches
The Adjus\bmen\b swi\bches are loca\bed insid\He \bhe coin door. 
1. Service  Swi\bch. Press \bhis swi\bch \bo ob\bain game credi\bs wi\bhou\b incremen\bing \bhe play 
me\ber.
2. Tes\b  Swi\bch Slide \bhe \bes\b swi\bch ON \bo en\ber \bes\b mode.
Tes\b mode allows \bes\bing \Hand \bhe changing of game se\H\b\bings. (Refer \bo
sec\bion  6-3  " T es\b  Mode"  page  43 )
3. Selec\b  Up/Down  Swi\bch This swi\bch is used \bo selec\b \bhe \bes\b required when in \bhe Tes\b Mode.
4. En\ber  Swi\bch This swi\bch is used \bo en\ber a selec\bed \bes\b and \bo change se\b\bings wi\bhin
a \bes\b. 
						

							
 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
be displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of
the selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
to return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to
return to normal game mode.
The Test Switch must always be in the “OFF” position for normal game mode.
MENU
COIN  OPTIONS...................................................Used to set the price of play.
GAME  OPTIONS..............................................Used to set the game options.
I/O TEST................................................Used for testing switches, lamps
and camera.
MONITOR  TEST................................................Used for setting the monitor.
SOUND  TEST................................................Used for setting the volume.
ADS  DATA................................................Used to view bookkeeping.
OTHERS................................................Used for testing the PCB.
The internal battery’s dead..............................Only displayed when the battery is
faulty (Refer to your Distributor).
SELECT  SW  :  CHOOSE ENTER SW : ENTER 
						

							
 6-3-1 Coin  Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost
and related settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then
press the Enter button.
3. Use the Select Up/Down switch to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu
screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech.
Ensure that the Game Cost is set to 1 Coin 1 Credit.
COIN  OPTIONS 
GAME  COST  (1P)1  COIN  (S)  1  CREDIT.........................(a)
DISCOUNT  CONTINUED1  COIN(S)    1  CREDIT.........................(b)
FREE  PLAYOFF............................ ( c )
EXIT
UP/DOWN  :  SELECT ENTER  SW  :  ENTER
m e t Ino i t p i r c s e D
t l u a f e D
t s o C e m a G ) a (9~ 1 e l b a t t e s - - - - s t i d e r c f o r e b m u n r o f d e r i u q e r s n i o C
t i d e r C 1 n i o C 1
t n u o c s i D ) b (
e u n i t n o C          e m a g e u n i t n o c r o f y a l p f o e c i r p d e c u d e r s w o l l A
) w o l f h s a c h t i w d e s u t o N ( . F F O r o 8 ~ 1 e l b a t t e s - - - -F F O
y a l P e e r F ) c ()o N ( f f O / ) s e Y ( n O - - - - t i d e r c r o f d e r i u q e r s n i o c o N
F F O 
						

							
 6-3-2 Game  Options
1. Select “GAME OPTIONS” on the menu screen to set the game
variables, the following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then
press the Enter button.
3. Use the  to Select Up/Down switch to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu
screen.
GAME  OPTIONS  [1/2]
[DEFAULT  IN  GREEN]
PCB  ID. 0............................... (a)
LINK ON 2............................... (b)
UP/DOWN:SELECTENTER  SW:ENTER
m e t Ino i t p i r c s e D
g n i t t e Stl u a f e D
D I B C Pe h t n o 0 h t i w 1 , 0 o t t e s : p u t e s t a e s o w t , t i n u e n O
. s r o t i n o m e h t t a g n i k o o l B C P e m a g t f e l
3 , 2 , 1 , 0 o t t e s : p u t e s t a e s r u o f , s t i n u o w T0h t i w
. s r o t i n o m e h t t a g n i k o o l B C P e m a g t f e l e h t n o3 o t 00
K C E H C K N I L: ) d e k n i l s B C P f o r e b m u n = n ( n N O
. y l t c e r r o c g n i k r o w e r a                     s n o i t a c i n u m m o C
. a t a d n o i t a c i n u m m o c g n i m o c n i o n s i e r e h T : F F O
. d e s i n g o c e r t o n s i a t a d n o i t a c i n u m m o C : G N
G N r o F F O f i y l t c e r r o c d e y a l p e b t o n n a c e m a g e h T
. e c n a t s i s s a r o f r o t u b i r t s i d r u o y t c a t n o C . d e y a l p s i d s i 
						

							

6-3-3 I/O Test
1. Selec\b “I/O TEST” on \bhe menu screen \bo \bes\b \bhe gun,swi\bches and camera. The following screen is displayed.
2. Use \bhe Selec\b Up/Down swi\bch \bo choose \bhe required i\bem \bhen press \bhe En\ber bu\b\bon \bo en\ber \bhe \bes\b.
3. Selec\b “EXIT” and press \bhe En\H\ber bu\b\bon \bo re\burn \bo \H\bhe menu screen. 
(a) Shows \bhe condi\bion of \bhe DIP Swi\bches on \bhe P\fB. In normal opera\bion all swi\bches are OFF. (If a swi\bch is ON, i\b will be displayed in red.)
(b)  Shows how many players a\Hre linked and condi\bio\Hn of link. 
(c ) \fhecks  func\bion  of  I/O  P\fB.  ( see \bSection \b6-3-3-1 \bp\fge \b47 )
(d ) Ini\bialize  game  po\ben\biome\bers.  ( see \bSection \b7 \bp\fge \b56 )
(e) Selec\bing \bhis i\bem allows \bhe gun aim \bo be checked. (See \b6-3-3-3 \bp\fge \b48 )
(f ) This  i\bem  allows  \bhe  gun  accuracy  \bo  be  se\b  ( see \b6-3-3-4 \bp\fge \b49 )
(g ) This  i\bem  allows  \bhe  \bes\bing  of  \bhe  swi\bches.  ( See \b6-3-3-5 \bp\fge \b50 )
(h) This i\bem allows \bhe \bes\bing and se\b\bing of \bhe camera. (See \b6-3-3-4 \bp\fge \b49 )
I/O TEST
DIP 4 12345678\b [ON:RED] .............................................. (a)
LINK ON\b\b2 .............................................. (b)
I/O  P\fB  \fHE\fK ............................................ ( c )
HOW TO  [I/F]  INITIALIZE ............................................ (d)
GUN  TEST ............................................ (e)
GUN  INITIALIZE ............................................ (f)
SWIT\fH TEST ............................................ (g)
\fAMERA  \fHE\fK ............................................ (h)
EXIT
SELE\fT  SW  :  \fHOOSE ENTER  SW  :  ENTER 
						

							Page 47
6-3-3-1 I/O\b PCB\b C\feck
1. Select\b‘I/\f\bPCB\bCHECK’\P\bfrom\bthe\bI/\f\bTest\bScreen.\bThe\bfollowing screen\bis\bdisplayed:-
Note: T\bis sc\feen is fo\f info\fmation only. No adjustments a\fe available.
6-3-3-2 How\bto\b[I/F\bInitialize] Select\b‘How\bto\b[I/F\bInitialize]’\bfrom\bthe\bI/\f\bTest\bmenu.\bThe\bfollowing 
screen\b is\b displayed. 
Note:  Initialization  cannot  be  executed  f\fom  t\bis  sc\feen.  ( see  7  page  56 )
I/\f\bTEST
DIP\b4 12345678  [ON=RED]
LINK ON 2
H\fW\bT\f\b[I\b/\bF\bINITIALIZE] 
I/F\bINITIALIZE\b:\b(1)\b\fR\b(2)
(1)\b H\fLDING\b SERVICE\b SW\b AND\bTURN\b \fN\bTEST\b SW 
(2)\b SELECT\b [GUN\b INITIALIZE]\b \fN\b I/\f\bTEST ENTER\bSW\b:\bENTER
I/\f\bTEST
DIP\b4 12345678  [ON=RED]
LINK ON 2
I/\f\b PCB\b CHECK
Master\b JV TX 3536 
NAMC\f\bLTD.\b;\bGM; VER\b\b0.766;\b\bJPN 
I/\f\b PCB\b C\fNNECT\b \fK 
NAMC\f\b LTD.\b ;ASCA-3;\bVER2.04
JPN,\b MULTIPURP\fSE\b +\b R\fTARY\b ENC\fDER
ENTER\b SW\b :\b ENTER 
						

							
I/O TEST
DIP 4 12345678\b [ON=RED]
LINK ON\b2
GUN  TEST
GUN  TRIGGER OFF 
SOLENOID OFF
GUN  LED OFF
GUN YAWING  RIGHT 0000
GUN YAWING  LEFT 0000
SLIDE  FORWARD 0000
SLIDE  BA\fK 0000
SLIDE  RIGHT 0000
SLIDE LEFT 0000
EXIT
ENTER SW : ENTER
6-3-3-3 Gun Test
1. Selec\b ‘GUN TEST’ from \bhe I/O Tes\b Screen. The following screen isdisplayed:-
2. Selec\b EXIT and press \bhe En\b\Her bu\b\bon \bo re\burn \bo \bhe I/O TEST screen.
Upon selec\bing \bhe GUN TEST screen, \bhe blue LED on \bhe gun will flash on and off regularly.
Note\b\fbout\bthe\bblue\bLED: The GUN LED on \bhe display will change al\berna\bely be\bween ON and 
OFF as \bhe blue LED flashes on \Hand off.
If \bhe gun \brigger is opera\bed during \bhis \bes\b, \bhe GUN TRIGGER,
SOLENOID and GUN LED  displays will change \bo green, \bhe blue LED
will flash dimly and \bhe solenoid will opera\be.

Twis\bing \bhe gun lef\b and righ\b will cause \bhe numbers displayed 
agains\b GUN YAWING RIGHT and GUN YAWING LEFT \bo change 
(\fbout\b-1350\b~\b1350) . OK will be displayed jus\b before \bhe gun is
\bwis\bed fully lef\b or righ\b.

Sliding \bhe gun lef\b, righ\b, \Hforward or backward wil\Hl cause \bhe 
numbers  displayed  agains\b  SLIDE  FORWARD,  SLIDE  BA\fK,  SLIDE 
RIGHT and SLIDE LEFT \bo change  (\fbout\b-900\b~\b1500\bforw\frd,\b-
1500\b~900\bb\fckw\frd\b\fnd\b-1200\b~\b1200\bleft\b\fnd\bright) . OK will be
displayed jus\b before \bhe limi\b of \bravel.
Note: If\bOK\bis\bnot\bdispl\fyed\b\fs\b\fbove\biniti\flize\bthe\bgun. (see \bsection \b6-3-3-4 \bp\fge \b49 ). 
						

							
 6-3-3-4 Gun  Initialize
1. Select ‘GUN TEST’ from the I/O Test Screen. The following screen is
displayed:-
2. As the gun is twisted left or right, the sight marked by “X” moves
accordingly. When the sight reaches a maximum value (i.e. when it
moves to the extreme left or right of the screen), the “X” will change
colour.
3. Ensure that the gun is completely central of all travel and then press
the service button to reset all values.
4. Select EXIT and press the Enter button to return to the I/O TEST
screen.
GUN  INITIALIZE
AIM  AT  CENTER  OF THE  CROSS
AND  PUSH  SERVICE  BUTTON
GUN YAWING
SLIDE FORWARD
0000
LEFTRIGHT
0000 0000
BACK
0000
TRIGGER :  ADJUST  SLIDE  AND  SIGHT
ENTER SW : ENTER
Median point
Median point 
						

							
	 6-3-3-5 Switch Test
1. Select “Switch Test” on the I/O menu screen to test the switches.
The following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT
and return to the I/O menu screen
(a) Not  Used
(b,c,d) Display will change from OFF to ON each time a switch is
operated.
(e) Display will change to UP or DOWN as the select is operated.
I/O TEST
DIP 4123456787 [ON/RED]
SWITCH TEST
COIN0 ............................................(a)
SERVICEOFF ............................................(b)
TESTON ............................................(c)
SELECTOFF ............................................(d)
ENTEROFF ............................................(e)
UP SELECT + ENTER : EXIT