Namco Final Furlong Operators Manual

Page 32
3. MAJOR COMPONENTS 

Page 33
4. MOVING THE MACHINE
This machine is fitted with castors to make it easier to move. Take care when 
moving the machine on an inclined surface.
The overall height of the machine is 2280mm. Take care of any overhead 
obstructions. (e.g. Light Fittings, Electric Cables etc.)
WARNING •NEVER turn the power to the machine ON until 
installation has been completed.
WARNING • In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a
securely connected...

Page 34
G GG G
G
DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit
Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an
Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger...

Page 35
F FF F
F
K KK K
K
I II I
I
N NN N
N
O OO O
O
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje,
nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i...

Page 36
P PP P
P
l ll l
lS SS S
S
ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS
INTERIORES APENAS
NÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-
1. Exteriores.
2. `Luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de
água perto de ar condicionados ou equipamentos calorificos e locais com temperaturas
excessivamente quentes ou frias.
3. Locais aonde ficaria colocada no caminho de saidas de emergência ou equipamentos
extintores de fogo.
4. Locais estruturalmente...

Page 37 5-1 Fitting the Header Assembly
The Header Assembly has a forward centre of gravity, so it is important
that at least 
two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is very high, and it is
important that a means of reaching the height safely, without stretching, is
available. (e.g. steps, step stools etc.)
1. Place the Header Assembly on top of the main cabinet so that the front
engages under the front retaining brackets.
2. Slide the header...

Page 38
4. Remove two Pozi Pan head screws (M4x12), flat and spring washers, and
remove the connector cover plate.
5. Connect the connector and refit the connector cover plate with the two
Pozi Pan head screws (M4x12), flat and spring washers. 

Page 39 5-2 Fitting the Ride Base Assembly
1. Place the Ride Base Assembly close to the monitor cabinet, ensuring that
the Side Safety Rail is to the outside.
2. Remove 8off security screws (M5x12) and remove both Base Front Cover
Plates.
3. Connect the connector between the Ride Base and the monitor cabinet
and push the Ride Base up to the monitor cabinet, taking care not to trap
the cable or connectors. 

Page 40
4.  Fit 4off Hex head screws (M10x35), flat and spring washers to join the
ride base to the monitor cabinet.
5. Refit the base front cover plates and secure with the 8off security screws (M5x12).
6 . Initialize the game before playing.  (See section 7 page 54)
Note:- 
When the machine is in its final position, lower the twelve level adjust\
ers, (4 on
the monitor cabinet and 4 on each ride base assy), with a spanner so th\
at the
machine is level and all castors are raised from the floor by...

Page 41 5-4 Fitting the Number Decals
1. When fitting the number decals ensure that the players are numbered
from left to right (viewed from the front) and that each horse has a
different number.
2. When linking two machines as a four player game, player one is extreme
left and player four is extreme right. (viewed from the front)