Home > Multi-Tech Systems > Communications System > Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide

Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide

Here you can view all the pages of manual Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide. The Multi-Tech Systems manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 161

161
Chapter 6: Technical Configuration
for Analog MultiVOIPs
(MVP210/410/810) 

Page 162

MultiVOIP User Guide Technical Configuration (Analog)
162
Configuring the Analog MultiVOIP
There are two ways in which the MultiVOIP must be configured before
operation:  technical configuration and phonebook configuration.
Technical Configuration.  First, the MultiVOIP must be configured to
operate with technical parameter settings that will match the
equipment with which it interfaces.  There are eight types of technical
parameters that must be set.
These technical parameters pertain to
(1) its...

Page 163

MultiVOIP User Guide Technical Configuration (Analog)
163
Local/Remote Configuration.  The MultiVOIP must be configured
locally at first (to establish an IP address for the MultiVOIP unit).  But
changes to this initial configuration can be done either locally or
remotely.
Local configuration is done through a connection between the
“Command” port of the MultiVOIP and the COM port of the computer;
the MultiVOIP configuration program is used.
Remote configuration is done through a connection between the...

Page 164

MultiVOIP User Guide Technical Configuration (Analog)
164
WARNING: Do not attempt to interface the MultiVOIP unit with
two control programs simultaneously (that is, by
accessing the MultiVOIP configuration program via
the Command Port and either the
MultiVoipManager program or the web browser
interface via the Ethernet Port).  The results of using
two programs to control a single VOIP
simultaneously would be unpredictable. 

Page 165

MultiVOIP User Guide Technical Configuration (Analog)
165
Local Configuration
This manual describes local configuration only.  For information on
remote configuration and management, see the MultiVoipManager
documentation.
Pre-Requisites
To complete the configuration of the
MultiVOIP unit, you must know several
things about the overall system.
Before configuring your MultiVOIP Gateway unit, you must know the
values for several IP and telephone parameters that describe the IP
network system and telephony...

Page 166

MultiVOIP User Guide Technical Configuration (Analog)
166
Analog Telephony Interface Parameters
(for MVP210/410/810)
The following parameters must be known about the PBX or telco
central office equipment to which the analog MultiVOIP will connect: :
➼
Analog Phone Parameters
Ask phone company or
telecom manager.
Needed for:
MVP810
MVP410
MVP210
Analog Telephony Interface Parameters:
Record for this VOIP Site

•  Which interface type (or “signaling”) is used?
                  
E&M_____    FXS/FXO_____
•...

Page 167

MultiVOIP User Guide Technical Configuration (Analog)
167
SMTP Parameters (for email call log reporting)
required  if log reports of
VOIP call traffic
 are to be sent by email
Optional
SMTP Parameters
Preparation Task:
Ask Mail Server
administrator to set up
email account (with
password) for the
MultiVOIP unit itself.
Be sure to give a unique
identifier to each
individual MultiVOIP
unit. .   
Get the IP address of the
mail server computer, as
well.To:  I . T. D e p a r t m e n t
 re : e mai l acc ount...

Page 168

MultiVOIP User Guide Technical Configuration (Analog)
168
Local Configuration Procedure (Summary)
After the MultiVOIP configuration software has been installed in the
‘Command’ PC (which is connected to the MultiVOIP unit), several
steps must be taken to configure the MultiVOIP to function in its
specific setting.  Although the summary below includes all of these
steps, some are optional.  
1. Check Power and Cabling.
2. Start MultiVOIP Configuration Program.
3. Confirm Connection.
4. Solve Common...

Page 169

MultiVOIP User Guide Technical Configuration (Analog)
169
Local Configuration Procedure (Detailed)
You can begin the configuration process as a continuation of the
MultiVOIP software installation.  You can establish your configuration
or modify it at any time by launching the MultiVOIP program from the
Windows Start menu.  
1. Check Power and Cabling.  Be sure the MultiVOIP is turned on and
connected to the computer via the MultiVOIP’s Command Port (DB9
connector at computer’s COM port; RJ45 connector at...

Page 170

MultiVOIP User Guide Technical Configuration (Analog)
170
3. Confirm Connection.  If the MultiVOIP is set for an available COM
port and is correctly cabled to the PC, the MultiVOIP main screen will
appear.  (If the main screen appears grayed out and seems inaccessible,
go to step 4.) 
Start reading Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide

Related Manuals for Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide

All Multi-Tech Systems manuals