Motorola Workabout Pro 4 User Guide

Configuration 3 - 69
•Tap Next to display the  Performance Settings  dialog box, and choose one of the performance options.
•Tap  Save.
Launching an Existing Profile
Your configured network profiles are listed in the  Manage Profiles screen.
• To activate a profile in the  Manage Profiles screen, tap and hold the sty lus on the profile you want 
to launch.
• In the drop-down menu, choose  Connect.
Resetting the Radio to Default Factory Settings
Resetting your unit, including  a clean start, will not...

CHAPTER 4 PERIPHERAL DEVICES & ACCESSORIES
PERIPHERAL DEVICES & ACCESSORIES 4
Carrying Accessories
There is a variety of carrying accessories to help the operator  work safely and comfortably with the 
Workabout Pro4.
Carrying AccessoryModel Number
Hand Strap - 7528 Long WA6025
Hand Strap - 7528 Short WA6125
Shoulder Strap for carrying case CV6021
Carry Case -7528 Long Standard WA6080
Carry Case - 7528 Long with unive rsal end-cap - open ended WA6081
Carry Case - 7528 Short Standard  WA6180
Carry Case -...

4 - 2 Workabout Pro4 (Windows Embedded CE 6.0) User Manual
Attaching the Hand Strap
The hand strap can be attached to the back of the Workabout Pro 4 to provide a secure means for operators to 
carry the hand-held.
The hand strap is attached to t he back of unit using two Phillips head screws provided with this accessory.
• Use a Phillips screwdr iver to attach the strap to the two thre aded inserts on the ba ck of the Workabout 
Pro4, near the top of the unit.
• Stretch the hand str ap toward the base...

Peripheral Devices & Accessories 4 - 3
The pistol grip is attached to the four threaded inserts on the back of the Wor kabout Pro4. Fou r Phillips head 
screws are provided with this accessory.
• Position the pistol grip so that it fits snugly over the back  of the unit and the holes in the pistol grip are 
aligned with the threaded inserts  on the back of the Workabout Pro4.
• Tighten the screws to a torque o f 3 lbs-in (3 kgf-cm) to secure the pistol grip in place.
• Insert the stylus in the base of...

4 - 4 Workabout Pro4 (Windows Embedded CE 6.0) User Manual
The trigger back cover kit, model number WA9302, provides a spe cial back cover that incorporates a scanner 
interface board and a  switch. This kit enables a pistol grip to trigger the following e nd cap scanners for the 
Workabout Pro 4:
The pistol grip is available sepa rately from this kit as model number WA6103.
Before You Begin
Installing the Back Plate
If your unit is using AC power, disconnect it.
• Remove the stylus from the end-cap.
•...

Peripheral Devices & Accessories 4 - 5
• Insert the flex cable from the end-cap into J2 on the interface board. The contacts  on the flex cable face 
towards the interface board.
Figure 4-2
1. Latch the connector.
2. Flip the back plate upwards.
3. Insert the flex cable from the Workabout Pro4 main logic boar d into J1 on the interface board. The con-
tacts on the flex cable face t owards the interface board. 
4. Latch the connectors.
5. Cut the Kapton tape square pr ovided in two equal pieces.
6. Remove...

4 - 6 Workabout Pro4 (Windows Embedded CE 6.0) User Manual
8. Fasten the new back plate onto the Workabout Pro4 using the s upplied screws (PN 9009770).
9. Insert the battery, and insta ll the battery compartment cover .
Installing the Flush Mount Pistol Grip
The Flush Mount Pistol Grip, model WA6103, is intended for use  with Workabout Pro4 units (7528 Long and 
7528 Short) which have the Trigger Back Plate installed. Review  the first few paragraphs at the beginning of 
The Trigger Back Plate Kit with...

Peripheral Devices & Accessories 4 - 7
4. Lower the Flush Mount Pistol Grip into place over the back plate, aligning the screw inserts on the 
hand-held with the screw  holes in the pistol grip.
5. Insert and tighten the four screws provided with the pistol g rip.
6. Replace the battery and battery cover.
7. Insert the stylus in the bottom of the pisto l grip handle.
Protective Carrying Case
A carrying case is available for the Workabout Pro4 to shield t he unit from damage. It is equipped with a soft...

4 - 8 Workabout Pro4 (Windows Embedded CE 6.0) User Manual
Figure 4-3Soft Shell Holster
• Insert the belt in the swivel holster pad.
• Attach the pad on either the le ft or right side of the holster case, depending on whether you are left- or 
right-handed.
• Fasten the belt comfortably aro und your waist. Slide the adjustable ring on the belt to tighten the holster 
in place.
• Connect the safety tether cord to  one of the clips on the bottom of the soft shell holster. Connect the other 
end to the hole...