Motorola Astro Radio Software 68 81098e85 O Manual

249 Key IDUse the UP/DOWN arrow keys to select the Key ID for this personality. 
The valid choices are:
If the received message does not specify a Key ID, the radio will use its 
current Key ID. 
XL Delay Following Key IDUse the UP/DOWN arrow keys to select the XL delay time following 
Key ID for this personality.  Values between 0 and 200 ms may be 
selected in 50-ms increments. The value selected for this field 
determines the length of time to wait, following a Key ID opcode 
transmission before the...

250
Personality MDC 
OptionsFrom the MAIN MENU, press F4, F6, F3 and then F7 to access this 
screen. This screen is visible only if the Signalling Type field in the 
Conventional Personality Screen (F4/F6/F3) is set to MDC. 
This screen permits access to additional MDC features and options to 
further customize the radio configuration to specific user needs.
Press Ta b to select the desired field, or press the desired function key 
(F1 - F10). If a field is highlighted, use the UP/DOWN arrow keys to 
select...

251 Call Alert EncodeUse the UP/DOWN arrow keys to enable/disable Call Alert Encode. If 
this feature is enabled, the user will be able to send pages to other 
radios.
Note:  If this feature is enabled and the selection of target radio(s) IDs
via Call List is to be made available to the user, data must be
programmed into the appropriate Call List table.
Selective Call DecodeUse the UP/DOWN arrow keys to enable/disable the MDC Selective 
Call Decode feature for this personality. If this feature is...

252
Conventional 
Personality Phone 
OptionsFrom the MAIN MENU, press F4, F6, F3 and then F8 to access this 
screen.
This screen allows the user to edit the Conventional phone 
configuration for each Conventional personality. Press Ta b to select 
the desired field, or press the desired function key (F1 - F10). If a field 
is highlighted, use the UP/DOWN arrow keys to select the desired 
choice or value.
Field Definitions
PersonalityThis is a view-only field.
Note: Refer to the Motorola Radio Catalog Sheets...

253
More Conventional 
Personality OptionsFrom the MAIN MENU, press F4, F6, F3 and then F9 to access this 
screen.
The CONVENTIONAL PERSONALITY OPTIONS MENU permits access 
to additional features and options to further customize the radio 
configuration to your specific communication needs.
Press Ta b to select the desired field, or press the desired function key 
(F1 - F10). If a field is highlighted, use the UP/DOWN arrow keys to 
select the desired choice or value.
Function Key Descriptions
F3 - PREV...

254
Field Definitions
PersonalityUse the UP/DOWN arrow keys to select the desired Conventional 
Personality. The number may also be entered directly.
Note: Refer to the Motorola Radio Catalog Sheets for the
maximum number of personalities allowed for this model.
Smart PTTUse the UP/DOWN arrow keys to enable/disable the Smart PTT 
function. The radio can inhibit transmission either on detection of a 
carrier or on detection of a non-matching PL code. This feature 
prevents users from listening in on (or...

255 Reverse Burst TOCUse the UP/DOWN arrow keys to enable/disable the Reverse Burst (PL), 
or turn-off code (DPL), to be transmitted after the radio is de-keyed. 
The Reverse Burst or turn-off code is used to signal the receiving radio 
that the transmission is ending and to indicate that audio must be 
muted. By muting before the carrier drops, the noise burst (squelch 
tail) on the receiving end is substantially reduced.
Squelch (Fine Tune)Use the UP/DOWN arrow keys to adjust the Squelch Fine Tuning....

256 Tx DeviationUse the UP/DOWN arrow keys to select the Transmitter Deviation for 
this personality. This is the maximum amount that modulation can 
cause the carrier to deviate from its unmodulated frequency. The 
choices are:
Note:  If 2.5 kHz is selected and the Rx Voice/Signal Type on the
CONVENTIONAL PERSONALITY screen (F4/F6/F3) is set to Non-
ASTRO for the current personality, the Secure/Clear Strapping field
(Voice Secure/Clear Strapping for radios capable of CAI Digital
Operation) on the...

257
ASTRO 
Conventional 
Personality OptionsFrom the MAIN MENU, press F4, F6, F3, F9 and then F6 to access this 
screen. 
Portables only
Mobiles only
This screen is available only if Rx Voice/Signal Type in F4/F6/F3 is set to 
either Mixed Mode or ASTRO. This screen allows you to edit information 
which relates to ASTRO Conventional operation. The settings selected 
on this screen are personality-specific and apply only to the ASTRO 
Personality numerically identified on the screen. For radio models...

258
Function Key Descriptions
F6 - TALKGROUPFunction key F6 (TALKGROUP) can be used to reach the ASTRO Conv 
Talkgroup Options screen. This screen is only available if the radio is 
equipped with CAI Digital operation. 
F7 - OTACS/OTACRThis screen can be accessed only if the OTACR/OTACS software option has 
been purchased for the radio. Brings up a screen which displays options 
settings for the Over-The-Air-Channel-Reassignment (OTACR) and 
Over-The-Air-Channel-Steering (OTACS).
Field Definitions...